Motorola LH4-B800E, HE-8000 I instruction manual Checking the Sewing Pattern

Page 62

6. CHECKING THE SEWING PATTERN

6. CHECKING THE SEWING PATTERN

You can check the sewing pattern which has been programmed, and also the needle zigzagging and feed operation. Checking can be carried out using test feed mode, or by turning the machine pulley by hand in manual mode. These two modes can also be combined in order to carry out checking.

6-1. Test feed mode (for checking the sewing pattern without turning the machine pulley by hand)

(3)

 

A

 

(14)

(7)

C

(8)

(15)

(16)

 

(13)(17)

2134Q

2135Q

1. Press the SELECT key (13) to change the mode to automatic mode. Use the program No. keys (7) and

(8) to select the number for the program to be checked, and then press the ENTER key (17). (The program number will stop flashing.)

2.Press the SELECT key (13) to change the mode to test feed mode.

("H***" and the number of stitches in the selected program will appear in the parameter display LED (14).)

3.Depress the treadle from the neutral position [A] to the 2nd step [C]. (The work clamp will drop.)

4.Return the treadle to the neutral position [A], and then depress it once more to the 2nd step [C]. The needle zigzag and feed mechanisms will each advance by one step while the treadle is being depressed. In addition, the needle zigzag and feed mechanisms will also advance by one step if you press the parameter UP key (15).

The needle zigzag and feed mechanisms will also retreat by one step if you press the parameter DOWN key (16).

(If the knife has been set to operate, the buzzer will sound and "C-On" will appear.)

5."Ho" will appear in the parameter display LED (14), and the machine will stop at the final stitch position.

6.Return the treadle to the neutral position [A], and then depress it to the 2nd step [C]. The sewing machine will move to the home position, and the work clamp will rise.

7.Press the SELECT key (13) to change the mode to automatic mode.

• If you press the SELECT key (13) during the checking operation, the mode will change to manual mode. If you press the SELECT key (13) once more, the mode will change back to test feed mode.

• If you would like to stop checking before the operation has completed, press the RESET key (3). The sewing machine will move to the home position, and the work clamp will move to the neutral position.

HE-8000

55

Page 61 Page 63
Image 62
Page 61 Page 63
Contents LH4-B800E HE-8000 Safety Instructions Environmental requirements Sewing Moving parts may cause injury Contents Changing Functions Using Safety devices Name of Each PartHE-8000 SpecificationsSubclass Standard sewing pattern list Leg parts Optional PartsSpecial needle plate Standing operation pedalAuxiliary table Tape guardRuler Replacement parts set for 70 mm buttonhole length ProgrammerInstallation Power tableVertical positioning Installing the motor Installing the flange nutInstalling the control box Installing the power switch Installing the bed baseInstalling the machine head Installing the head restInstalling the operation panel Connecting the machine head harness Connecting the cordsConnecting the ground wire Connecting the motor harness Connect the connectors of the feed motor harnessConnecting the power cord Connecting the standing pedal harness option Table leg installation treadle support plates Installing the transformerFloor installation Installation underneath the work table Connecting the cordsInstalling the V-belt Adjusting the finger protector Installing the belt cover plateAdjusting the belt retainer Adjusting the treadle return pressure Installing the treadleAdjusting the treadle pressure Adjusting the treadle strokeInstalling the spool stand Installing the eye guard Lubrication Lubricating the bed baseLubricating the rotary hook Rotary hook lubrication adjustmentLubricating the arm Installing the belt cover Operation Part names and functionsProgram mode indicator Test feed mode indicatorManual mode indicator Select keyHome position return preparation Before starting home position returnOperating the treadle Three pedals Operating the standing pedal optionTwo pedals + kick pedal Parameter table Program setting methodProgram initialization condition Setting items Setting range Unit Default Zigzag width 3.0 mm Setting items Setting range Unit Default Front tack pitch except radial 05 1.00 mm Setting items Setting range Unit No. of stitches in X direction for saw-shaped rear Start backtack width 3.0 mm Saw-shaped underlays Saw-shaped underlay bar tack X stitch no Stitches Rear bar tack tension release timing Stitches Changing program details Bar tacking stitches being cut by the knife 13 17 2118Q 2123Q Rectangle Rear tack vector shape programsTriangle Saw-shapeSaw-shape underlay Underlay programsUnderlays sewn together Rectangle underlayCutter operation Center knife standard Rear knifeCycle program Changing the production counter Changing the lower thread counter setting value Program memo contents Using the program memosAdding patterns created using the BAS-PC/300 Adding patterns to a P-ROM→ 1 → 2 → 3 →….. → 90→ P1 → P2 → …… → P9 → 1 → 2 → …… Checking the Sewing Pattern 2136Q Installing the needle Correct USEThreading the upper thread Threading the thread at the sewing start positionAdjusting the bobbin winding amount Winding the lower threadWhip stitch plain stitch Threading the bobbin caseStitch patterns Purl stitch seal stitchThread tension Reference thread tension Thread take-up spring tensionThread take-up spring height Sewing SewingIf the emergency stop switch is pressed during sewing To finish sewing in this conditionIf the thread breaks during sewing Emergency stopThread breakage before sewing is finished To continue sewing from around the location of the breakageWhen resuming sewing in test feed mode or manual mode Lower thread counterMaintenance CleaningDraining the oil Cleaning the control box air inlet portCleaning the eye guard Cleaning the length feed plate Checking the needleStandard Adjustments Needle bar heightNeedle and hook timing adjustment Adjusting the clearance between needle and hook pointAdjusting the work clamp pressure Adjusting the knife installationAdjusting the upper thread trimming Scissors fully opening timing adjustment Adjusting the upper thread scissors opening timingGradual opening timing adjustment Adjusting the needle up stop position Adjusting the lower thread clamp timingAdjusting the bobbin presser Changing Functions Using the Memory Switches Memory switch table Initializing all programs Settings which are initializedProgram Initialization Initializing a single programChanging Functions Using the DIP Switches Panel DIP switchesPanel DIP switch table DipswaControl circuit board DIP switches DIP switch inside the control box table Gauge Parts List Needle plateFor flat cutter Work clamp assy, W/F-G Finger guard Gauge Parts List Cutter Error Code Table Like to keep the program which exceeds the area Troubleshooting TroubleshootingCause Needle is incorrectly installed 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone

LH4-B800E, HE-8000, HE-8000 I specifications

Motorola has long been a pioneer in communication technologies, and the introduction of models like the HE-8000 I, HE-8000, and LH4-B800E showcases the company's commitment to quality and innovation in the realm of wireless communication devices. These models offer a blend of advanced features, robust design, and cutting-edge technologies that cater to various user needs.

The Motorola HE-8000 I is characterized by its sleek and ergonomic design, making it comfortable for extended use. It boasts a long battery life, ensuring that users can stay connected for longer periods without the need for frequent recharging. This model is equipped with enhanced audio clarity, utilizing advanced noise-canceling technology to ensure clear communication even in noisy environments. Furthermore, the HE-8000 I features multi-channel capabilities, allowing users to switch between multiple channels effortlessly.

Similar in design and functionality, the HE-8000 model enhances user experience with its intuitive interface. This model supports Bluetooth connectivity, making it compatible with a wide range of devices, including smartphones and tablets. The HE-8000's build quality is reinforced for durability in rugged conditions, making it an ideal choice for professionals who require reliable communication tools in challenging environments.

The LH4-B800E represents the pinnacle of Motorola's commitment to delivering versatile communication solutions. It includes advanced features such as GPS tracking and real-time location sharing, which are essential for teams working in logistics, security, and emergency services. The LH4-B800E also stands out for its superior range, offering extended coverage even in remote areas, ensuring that users remain connected.

All three models incorporate advanced encryption technologies to enhance security and protect sensitive communications. They are built to be water and dust resistant, meeting industry standards for ruggedness, which ensures reliable operation in various weather conditions.

Ultimately, the Motorola HE-8000 I, HE-8000, and LH4-B800E exemplify the brand's commitment to innovation and user-centric design. With a focus on clear communication, extended battery life, and robust connectivity options, these devices are well-suited for a wide array of professional applications, from fieldwork to corporate communication. Whether for individual use or in a team setting, these Motorola models are engineered to empower users with reliable and efficient communication solutions, reflecting the company’s legacy in the telecommunications industry.
Top Page Image Contents