Motorola LH4-B800E, HE-8000 I instruction manual If the thread breaks during sewing, Emergency stop

Page 72

8. SEWING

Emergency stop

Press the EMERGENCY STOP switch to stop the machine, and then reset the switch. (When panel DIP switch A-3 is ON, an emergency stop occurs when the treadle is depressed backward.)

Thread breakage detection

The machine stops when a thread breakage is detected.

Thread the thread.

Resuming sewing

Press parameter keys (15) and (16) to move to the point to resume sewing.

Re-sewing

(with work clamp still lowered)

While pressing the parameter down key (16), press the RESET key (3).

Return to the sewing start position (work clamp lowered).

Next sewing

(work clamp raised)

Press the RESET key (3).

Return to the sewing start position (work clamp raised).

Depress the treadle. (Machine will start.)

8-1-2. If the thread breaks during sewing

The sewing machine will stop and "E-01" will appear in the parameter display LED (14). Re-thread the thread.

1. To finish sewing in this condition

Next sewing

1)Press the RESET key (3).

(The feed mechanism will return to the sewing start position and the work clamp will rise.)

2)Sewing will start again when the treadle is depressed.

2. To start sewing again from slightly before or after the thread breakage

Resuming sewing

1)Press the parameter UP key (15) to move the zigzag and feed mechanisms to the next sewing position. Press the parameter DOWN key (16) to move the zigzag and feed mechanisms to the previous sewing position. (The "E-01" display will be cleared at this time.)

2)Move to the position to continue sewing from, and then depress the treadle. The rest of the sewing will be carried out.

3.To sew from the sewing start point without raising the work clamp (without shifting the material) Re-sewing

1)While pressing the parameter DOWN key (16), press the RESET key (3).

(The feed mechanism will return to the sewing start position, but the work clamp will not rise.)

2)Depress the treadle to start sewing.

If the emergency stop or thread breakage detector operates during sewing, the needle will move to the right before the sewing machine stops, in order to make threading easier.

HE-8000

65

Image 72
Contents LH4-B800E HE-8000 Safety Instructions Environmental requirements Sewing Moving parts may cause injury Contents Changing Functions Using Safety devices Name of Each PartSpecifications SubclassHE-8000 Standard sewing pattern list Optional Parts Special needle plateLeg parts Standing operation pedalTape guard RulerAuxiliary table Replacement parts set for 70 mm buttonhole length ProgrammerInstallation Power tableVertical positioning Installing the motor Installing the flange nutInstalling the control box Installing the power switch Installing the bed baseInstalling the machine head Installing the head restInstalling the operation panel Connecting the cords Connecting the ground wireConnecting the machine head harness Connecting the motor harness Connect the connectors of the feed motor harnessConnecting the power cord Connecting the standing pedal harness option Installing the transformer Floor installationTable leg installation treadle support plates Installation underneath the work table Connecting the cordsInstalling the V-belt Installing the belt cover plate Adjusting the belt retainerAdjusting the finger protector Installing the treadle Adjusting the treadle pressureAdjusting the treadle return pressure Adjusting the treadle strokeInstalling the spool stand Installing the eye guard Lubrication Lubricating the bed baseRotary hook lubrication adjustment Lubricating the armLubricating the rotary hook Installing the belt cover Operation Part names and functionsTest feed mode indicator Manual mode indicatorProgram mode indicator Select keyHome position return preparation Before starting home position returnOperating the treadle Operating the standing pedal option Two pedals + kick pedalThree pedals Program setting method Program initialization conditionParameter table Setting items Setting range Unit Default Zigzag width 3.0 mm Setting items Setting range Unit Default Front tack pitch except radial 05 1.00 mm Setting items Setting range Unit No. of stitches in X direction for saw-shaped rear Start backtack width 3.0 mm Saw-shaped underlays Saw-shaped underlay bar tack X stitch no Stitches Rear bar tack tension release timing Stitches Changing program details Bar tacking stitches being cut by the knife 13 17 2118Q 2123Q Rear tack vector shape programs TriangleRectangle Saw-shapeUnderlay programs Underlays sewn togetherSaw-shape underlay Rectangle underlayCutter operation Center knife standard Rear knifeCycle program Changing the production counter Changing the lower thread counter setting value Using the program memos Adding patterns created using the BAS-PC/300Program memo contents Adding patterns to a P-ROM→ 1 → 2 → 3 →….. → 90→ P1 → P2 → …… → P9 → 1 → 2 → …… Checking the Sewing Pattern 2136Q Installing the needle Correct USEThreading the upper thread Threading the thread at the sewing start positionAdjusting the bobbin winding amount Winding the lower threadThreading the bobbin case Stitch patternsWhip stitch plain stitch Purl stitch seal stitchThread tension Thread take-up spring tension Thread take-up spring heightReference thread tension Sewing SewingIf the emergency stop switch is pressed during sewing To finish sewing in this conditionIf the thread breaks during sewing Emergency stopThread breakage before sewing is finished To continue sewing from around the location of the breakageWhen resuming sewing in test feed mode or manual mode Lower thread counterMaintenance CleaningCleaning the control box air inlet port Cleaning the eye guardDraining the oil Cleaning the length feed plate Checking the needleStandard Adjustments Needle bar heightNeedle and hook timing adjustment Adjusting the clearance between needle and hook pointAdjusting the work clamp pressure Adjusting the knife installationAdjusting the upper thread trimming Adjusting the upper thread scissors opening timing Gradual opening timing adjustmentScissors fully opening timing adjustment Adjusting the lower thread clamp timing Adjusting the bobbin presserAdjusting the needle up stop position Changing Functions Using the Memory Switches Memory switch table Settings which are initialized Program InitializationInitializing all programs Initializing a single programChanging Functions Using the DIP Switches Panel DIP switchesPanel DIP switch table DipswaControl circuit board DIP switches DIP switch inside the control box table Gauge Parts List Needle plateFor flat cutter Work clamp assy, W/F-G Finger guard Gauge Parts List Cutter Error Code Table Like to keep the program which exceeds the area Troubleshooting TroubleshootingCause Needle is incorrectly installed 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone

LH4-B800E, HE-8000, HE-8000 I specifications

Motorola has long been a pioneer in communication technologies, and the introduction of models like the HE-8000 I, HE-8000, and LH4-B800E showcases the company's commitment to quality and innovation in the realm of wireless communication devices. These models offer a blend of advanced features, robust design, and cutting-edge technologies that cater to various user needs.

The Motorola HE-8000 I is characterized by its sleek and ergonomic design, making it comfortable for extended use. It boasts a long battery life, ensuring that users can stay connected for longer periods without the need for frequent recharging. This model is equipped with enhanced audio clarity, utilizing advanced noise-canceling technology to ensure clear communication even in noisy environments. Furthermore, the HE-8000 I features multi-channel capabilities, allowing users to switch between multiple channels effortlessly.

Similar in design and functionality, the HE-8000 model enhances user experience with its intuitive interface. This model supports Bluetooth connectivity, making it compatible with a wide range of devices, including smartphones and tablets. The HE-8000's build quality is reinforced for durability in rugged conditions, making it an ideal choice for professionals who require reliable communication tools in challenging environments.

The LH4-B800E represents the pinnacle of Motorola's commitment to delivering versatile communication solutions. It includes advanced features such as GPS tracking and real-time location sharing, which are essential for teams working in logistics, security, and emergency services. The LH4-B800E also stands out for its superior range, offering extended coverage even in remote areas, ensuring that users remain connected.

All three models incorporate advanced encryption technologies to enhance security and protect sensitive communications. They are built to be water and dust resistant, meeting industry standards for ruggedness, which ensures reliable operation in various weather conditions.

Ultimately, the Motorola HE-8000 I, HE-8000, and LH4-B800E exemplify the brand's commitment to innovation and user-centric design. With a focus on clear communication, extended battery life, and robust connectivity options, these devices are well-suited for a wide array of professional applications, from fieldwork to corporate communication. Whether for individual use or in a team setting, these Motorola models are engineered to empower users with reliable and efficient communication solutions, reflecting the company’s legacy in the telecommunications industry.