Pella 80GY0102 warranty 3SETTING and Fastening the Window

Page 5

3SETTING AND FASTENING THE WINDOW

"

TWO OR MORE PEOPLE WILL BE

REQUIRED FOR THE FOLLOWING STEPS.

A.Insert the window from the exterior of the building. Place the bottom of the window on the spacers at the bottom

of the opening, then tilt the top into position. Center the window between the sides of the opening to allow clearance for shimming, and insert one roofing nail in the first hole from the corner on each end of the top nailing fin. These are used to hold the window in place while shimming it plumb and square.

B.Plumb and square window. Place shims between the window frame and the rough opening at each installation screw hole.

Adjust the shims as required to plumb and square the window in the opening.

Windows with Installation Clips only: Shim between each installation clip and the rough opening.

Note: DO NOT over shim.

C.Check the interior reveal. Make sure the measurement from the interior face of the

window to the interior face of the wall

is equal at several points around the $ window.

Note: If the dimensions are not equal, check to make sure the fins are folded out to 90° at all points.

#

NN



*/$)&4



 

 



 





 



 

 





 

 

 

 

 

 

 

 



 

 

 

 

 

 

*OUFSJPS

#

D. Check window operation (vent units only). Remove the shipping spacers, unlock the window and open and close it a few times to check for proper operation. Close and lock the window.

Note: If there are any problems with the operation of the window,

&

recheck shim locations and adjust for plumb and square.

E. Fasten the window to opening by driving 2" galvanized roofing nails into each pre-punched hole in the nailing fin.

Note: Make sure the fin corner is lying as flat as possible.

4INTEGRATING THE WINDOW TO THE WATER RESISTIVE BARRIER

Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Important Safety Information Cut the water resistive barrier 1C Rough Opening PreparationPreparing the Window Windows using Installation Clips Windows using Frame ScrewsRecheck shim locations and adjust for plumb and square 3SETTING and Fastening the WindowApply flashing tape to diagonal cuts . Cut 5SECURING the Window Frame Screw InstallationFasten the window to the opening by driving two #8 x 1-1/4 Securing the Window 6INSTALLATION Clip Method7INTERIOR Seal #3*$,7&/&&3 53 8SEALING the Window to the Exterior Wall CladdingInterior Finishing Care and Maintenance Important NoticeExterior Finishing Closing themCam hook Installing Roto Cover and CrankLock Lever Removal and Insertion

80GY0102 specifications

The Pella 80GY0102 is a sophisticated and high-performance sliding patio door that exemplifies both elegance and functionality. Designed for homeowners seeking to enhance their living spaces, this door offers a perfect balance of beauty and energy efficiency, making it an ideal choice for both modern and traditional homes.

One of the most notable features of the Pella 80GY0102 is its exceptional energy efficiency. It utilizes advanced insulation technologies, including double or triple-pane glass options, which significantly reduce heat transfer. This means that the door helps maintain a comfortable indoor temperature, keeping homes warm in winter and cool in summer while helping to reduce energy bills. Additionally, the door is designed with Low-E (low emissivity) glass coatings that reflect infrared heat, further enhancing its energy-saving capabilities.

The frame of the Pella 80GY0102 is constructed from durable fiberglass or wood, which not only contributes to its aesthetic appeal but also ensures longevity and resilience against the elements. The sturdy construction helps in resisting warping, cracking, and rotting, making it a maintenance-free option for homeowners.

In terms of security, the Pella 80GY0102 does not compromise. It features a multi-point locking system that provides added security against intrusions, giving homeowners peace of mind. The lock's design allows for easy operation while ensuring that the door remains securely closed.

Another highlight of this patio door is its smooth sliding mechanism, which makes opening and closing effortless. The door's rollers are designed to glide smoothly, providing convenient access to outdoor spaces while minimizing wear over time. Additionally, homeowners can choose between various colors and finishes to complement their home’s exterior and interior décor.

Customization is a key aspect of the Pella 80GY0102. Homeowners can select from a variety of sizes, grid patterns, and hardware options to create a personalized look that fits their individual style and needs.

Overall, the Pella 80GY0102 stands out as an excellent option for those looking to enhance their home's aesthetics while prioritizing energy efficiency, durability, and security. Its cutting-edge features and customizable options make it a valuable addition to any residential property.
Top Page Image Contents