Pella 80GY0102 warranty Securing the Window 6INSTALLATION Clip Method, 7INTERIOR Seal

Page 7

B.Drill 1/8" x 1" deep pilot holes into the rough framing through the clearance holes in the unit frame.

C.Fasten the window to the opening by driving #10 x 3-1/2" corrosion resistant wood screws into each of the pre-drilled clearance holes.

Note: Screws MUST be driven straight or angled slightly toward the exterior to prevent interference with the lock mechanism. Drive the screws until snug but DO NOT over- tighten the screws. DO NOT bend or bow the unit frame.

YDPSSPTJPO

SFTJTUBOUXPPETDSFX

$

#

 

Y

 

DPSSPTJPOSFTJTUBOU

 

XPPETDSFX

 

$

#

%SJMMEJBNFUFSQJMPU

IPMFUISPVHIUIFDMFBSBODF

 

IPMFJOUIFGSBNF

SECURING THE WINDOW -

 

6INSTALLATION CLIP METHOD

 

A. Fasten the window to the opening by driving two #8 x 1-1/4"

"

corrosion resistant screws into the pre-punched holes in the clips.

If clips are bent and fastened to the interior stud/block, install the

 

screws as close to the bend as possible.

 

Note: DO NOT shim above the window. For masonry openings use two 3/16" x 1-1/2" masonry screws per clip. Pre-drill the masonry before attempting to drive the screws in.

7INTERIOR SEAL

Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer’s recommendations for

application. Use of high pressure foams or improper application of the" foam may cause the window frame to bow and hinder operation.

A.Apply insulating foam sealant. From the interior, insert the nozzle of the applicator approximately 1" deep into the space between the window and the rough opening and apply a 1" deep bead of foam. This will allow room for expansion of the foam and will minimize squeeze out. If using foam other than Great Stuff ™ Window and Door Insulating Foam Sealant by the Dow Chemical Company, allow the foam to cure completely (usually 8 to 24 hours) before proceeding to the next step.

Note: DO NOT completely fill the space from the back of the fin to the interior face of the opening.

*OUFSJPS

B. Check window operation (vent units only) by opening and closing the window.

Note: If the window does not operate correctly, check to make sure it is still plumb, level, square and that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife. Adjust the shims, and reapply the insulating foam sealant.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Important Safety Information Cut the water resistive barrier 1C Rough Opening PreparationPreparing the Window Windows using Installation Clips Windows using Frame ScrewsRecheck shim locations and adjust for plumb and square 3SETTING and Fastening the WindowApply flashing tape to diagonal cuts . Cut 5SECURING the Window Frame Screw Installation7INTERIOR Seal Securing the Window 6INSTALLATION Clip MethodFasten the window to the opening by driving two #8 x 1-1/4 #3*$,7&/&&3 53 8SEALING the Window to the Exterior Wall CladdingClosing them Care and Maintenance Important NoticeInterior Finishing Exterior FinishingLock Lever Removal and Insertion Installing Roto Cover and CrankCam hook

80GY0102 specifications

The Pella 80GY0102 is a sophisticated and high-performance sliding patio door that exemplifies both elegance and functionality. Designed for homeowners seeking to enhance their living spaces, this door offers a perfect balance of beauty and energy efficiency, making it an ideal choice for both modern and traditional homes.

One of the most notable features of the Pella 80GY0102 is its exceptional energy efficiency. It utilizes advanced insulation technologies, including double or triple-pane glass options, which significantly reduce heat transfer. This means that the door helps maintain a comfortable indoor temperature, keeping homes warm in winter and cool in summer while helping to reduce energy bills. Additionally, the door is designed with Low-E (low emissivity) glass coatings that reflect infrared heat, further enhancing its energy-saving capabilities.

The frame of the Pella 80GY0102 is constructed from durable fiberglass or wood, which not only contributes to its aesthetic appeal but also ensures longevity and resilience against the elements. The sturdy construction helps in resisting warping, cracking, and rotting, making it a maintenance-free option for homeowners.

In terms of security, the Pella 80GY0102 does not compromise. It features a multi-point locking system that provides added security against intrusions, giving homeowners peace of mind. The lock's design allows for easy operation while ensuring that the door remains securely closed.

Another highlight of this patio door is its smooth sliding mechanism, which makes opening and closing effortless. The door's rollers are designed to glide smoothly, providing convenient access to outdoor spaces while minimizing wear over time. Additionally, homeowners can choose between various colors and finishes to complement their home’s exterior and interior décor.

Customization is a key aspect of the Pella 80GY0102. Homeowners can select from a variety of sizes, grid patterns, and hardware options to create a personalized look that fits their individual style and needs.

Overall, the Pella 80GY0102 stands out as an excellent option for those looking to enhance their home's aesthetics while prioritizing energy efficiency, durability, and security. Its cutting-edge features and customizable options make it a valuable addition to any residential property.
Top Page Image Contents