Crane Merchandising Systems 480 manual Replace a Motor with a Spiral Bearing, Remove a Motor

Page 28

Refreshment Center Operators’ Guide

Tray Set-Up

 

 

Replace a Motor with a Spiral Bearing

Remove A Motor:

1.Disconnect the harness from the motor.

(See "Connect and Disconnect a Motor Harness" on page 24).

2.Remove the spiral. (See "Remove and Install Spirals" on page 25).

3.Remove the spiral coupler. (See "Remove a Spiral Coupler" on page 26).

4.Remove the motor. (See "Remove and Install a Spiral Motor" on page 27).

5.Install A Spiral Bearing:

a. Put the gear into position in this set-up as shown.

SPIRAL

BEARING

BACKWALL

OF TRAY

GEAR

˜

SPIRAL

COUPLER

b. Install the spiral coupler. (See "Install a Gear" on page 28).

December 2004

23

4800006

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page Table of Contents Table of Contents December Iii 4800006 Table of Contents Introduction Exterior ViewInterior View Power Requirements Unpack the MachineControls and Indicators Normal Conditions HeartbeatTurn the Merchandiser on and OFF Moving the Merchandiser Through a Narrow Doorway Remove the Bottom and Top PanelsMove the Merchandiser through the Opening Reassemble the MerchandiserOpen the Rear Outlet Diffuser Position the MerchandiserConfigure Machine for Dual Zone Set machine for two tray configuration version Initial Set-Up Set the machine for three tray configuration version Initial Set-Up Refreshment Center Operators’ Guide Version 2 Duct System See Figure , , on Tray Set-Up Place a Tray in the Loading PositionSet up Trays to Vend Products Set Up a Tray To Vend Wide ProductsRemove a Snack or Candy Tray Rear of Tray Remove a Bottle Tray Remove and Install Column Dividers Operate a Tray Outside of the MachineRemove the motor. See Remove and Install a Spiral Motor on Replace a Motor with a Spiral BearingRemove a Motor See Connect and Disconnect a Motor Harness onDisconnect a Motor Harness Connect and Disconnect a Motor HarnessConnect a Motor Harness Remove and Install Spirals Spiral Retainer Count Color AssemblyTo Install a Spiral Remove a Spiral CouplerTo Remove a Spiral Choose a Clockwise or Counterclockwise SpiralInstall a Spiral Motor Remove and Install a Spiral MotorRemove a Spiral Motor Use a Gear when Install a GearPosition the Gear Install a Spiral Coupler When Used with a MotorWhen Used with a Coupler Bearing Spiral Coupler OrientationSee Install a Tray in the Merchandiser on Move a Tray Up or DownInstall a Tray in the Merchandiser Install and Remove a Product Spacer Install a Product SpacerAdjust a Product Spacer Remove a Product SpacerSpecial Considerations General Tray LoadingAlso, see Spiral Wall Retainer Usage on Spiral Wall Retainer Usage Configure the Merchandiser to vend Lunch Buckets Product Pusher UsageConfigure the Merchandiser for Vending Top Shelf Return the Trays to the Vending Position Install and Set Price Labels Install Price LabelsAdjust the Price Roll Install the Selection ID NumbersSee the figures below for snack and candy tray positions SureVend Health Control Health Control Test the Health ControlFinal Installation Level the MerchandiserInstall the Base Plate Install the Lock Cylinder Install the Optional Cash Box LockSet the Quarter Switch Set Up the Coin MechanismLoad the Coin Mechanism Spiral Indexing Procedure One Spiral, One Motor Operational Readiness CheckSpiral Indexing Procedure Two Spirals, One Or Two Motors Test the Bill ValidatorProgramming Intro DisplaysOther Keys Function KeysOne Last Thing Control Panel Switches Explained Diagnostic Messages onProgramming Flow Charts DiagnosticsMisc Gain Access to the Supervisor Mode Supervisor Mode OnlyEnter a NEW Supervisor Code Enter a Freevend CodeLock or Unlock Mode or Payout Keys Turn Talker Mode on or OFFAssign a Code to View Data Without Opening the Door UsageSelect DEX or Printer Mode SET DEX OptionsPrinter Mode Only Select Printer Baud RateSelect Display Language Select Coin MechanismSetup of a Non-Standard Bill Validator on Select Bill Validator and OptionsProgramming Procedures Refreshment Center Operators’ Guide Initial Setup of a NON-STANDARD Bill ValidatorSelect Monetary Options BalanceFAIL= ExampleSET UP Winner Mode WIN-orAdvanced Options AN ExampleView or SET Machine Configuration NON-PERISHABLE Food onlyEnable or Disable Trays SET UP Basic Surevend Options SET Surevend UP the Surevend ANTI-JACKPOT FeatureCOUPLE/UNCOUPLE Tray Motors Couple NON-ADJACENT MotorsSET Defrost Options Supervisor Mode Only DAYShow the Temperature in Standby Mode Press , then until the display showsView Machine Temperature See Health Control onView Surevend Software Version View Software VersionSET the Date SET the Time of DAYSET Daylight Savings Option SET TIME-OF-DAY Inhibited Vending SET TIME-OF-DAY Free VendingSET TIME-OF-DAY Discount Vending Time Interval EditingDISCT----K Programming Procedures Refreshment Center Operators’ Guide Continue Select a Standby MessageSelect AN OUT-OF-SERVICE Message Select a Freevend MessageEdit Custom Messages END of Message CharacterJZK Entering Your MessagePayout Coins SET PricesSet the Entire Machine to One Price Set All Selections on a Tray to One PriceView Nonresettable Sales and Vend Data View Sales Data Three Different WaysView Card Reader Paid Sales Not shown if total is zeroView Coupon Sales View Total Paid VendsView Amount Coin BOX Clear Paid Sales Data onlyView Amount Validator View Discount Sales by Time Interval View Freevend Sales by Time IntervalView Free Vends DecemberHEALTH 2004OFF01/3014.09MAX.69 View Time DataDate and time of the last vend of that selection View Total Unpaid Sales View Total Unpaid VendsView Number of Test Vends View Machine ID NumberSureemptxxxx View Surevend DataTest Vend Selections and Verify Credit Added Test the MotorsView Motor Status by Tray Suretst Test the Surevend SystemDEX Mode Only Test the DisplayDownload Data to a Pdcd SET Freevend OptionsView Diagnostic Messages Error MessagesBoth Eady Xxnn Screen. See Test the SureVend System onIndex Refreshment Center Operator’s Guide Index Terms and Conditions of Sale

480 specifications

Crane Merchandising Systems 480 is a versatile vending machine that has redefined the way consumers interact with automated retail. This cutting-edge machine brings a multitude of features, technologies, and characteristics that cater to modern consumer needs while promoting operational efficiency.

One of the primary features of the Crane 480 is its flexible product selection. It is designed to accommodate a wide variety of items, from snacks and beverages to healthier options. With adjustable shelving and configurable product slots, operators can easily tailor the machine’s offerings based on consumer preferences, seasonal trends, or specific location requirements. This adaptability makes it an ideal choice for various environments, including offices, schools, and public spaces.

The Crane 480 employs advanced technology for enhanced user experience. A notable feature is its user-friendly touchscreen interface, which allows customers to browse products seamlessly. The high-resolution display presents vibrant images and product information, making it easier for users to make informed choices. The intuitive interface also supports multiple languages, catering to diverse customer bases.

Another significant aspect is the machine's cashless payment technology. The Crane 480 is equipped to handle various payment methods, including contactless cards, mobile wallets, and even cryptocurrency. This flexibility not only accelerates the transaction process but also meets the growing demand for convenience in payment options.

Energy efficiency is a standout characteristic of the Crane 480. It utilizes LED lighting and energy-saving components, minimizing power consumption without compromising performance. This eco-friendly approach not only reduces operational costs for operators but also aligns with the increasing consumer demand for sustainable practices.

In addition to its operational features, the Crane 480 offers robust remote monitoring capabilities. Through integrated telemetry technology, operators can gain real-time insights into machine performance, inventory levels, and sales data. This information allows for better inventory management and timely restocking, ensuring that popular items are always available, ultimately enhancing customer satisfaction.

Durability is another hallmark of the Crane 480. Constructed with high-quality materials, the machine is designed to withstand the rigors of high-traffic environments while requiring minimal maintenance. Its sleek, modern design also ensures that it fits seamlessly into any location, enhancing the aesthetic appeal of the space.

In summary, Crane Merchandising Systems 480 stands out as a leader in the vending machine industry. Its blend of flexibility, advanced technology, energy efficiency, and durability makes it an excellent choice for both operators and consumers alike. The combination of these features ensures that it not only meets but exceeds the expectations of the vending market in today’s fast-paced world.
Top Page Image Contents