Crane Merchandising Systems 480 manual Controls and Indicators

Page 9

Introduction

Refreshment Center Operators’ Guide

Controls and Indicators

DOOR SWITCH. When the cabinet door is open, this switch turns off the compressor and evaporator fan.

INTERLOCK SWITCH. (230 volt models only) Turns off the glass heater and display lights when the cabinet door is open. Pull the switch out to restore high voltage for maintenance.

LOW VOLTAGE SWITCH. Tells the controller software the main door is open or closed. MESSAGE DISPLAY. This is how the merchandiser communicates with the outside world. Customers can see messages about how much money they have put into the merchandiser. The message display also tells customers when a selection is sold out and when vending is free, inhibited, or discounted. The message display shows you what you are doing when you program the merchandiser, and can show you what is wrong if there is a failure.

FREE VEND KEYSWITCH (OPTIONAL). This allows someone (other than maintenance personnel) to set the merchandiser to free vend without opening the door.

SELECTION KEYPAD. The customer uses this keypad to make selections. Maintenance people may use this keypad during programming.

COIN RETURN BUTTON. Returns any coins paid into the merchandiser prior to a vend.

BILL ACCEPTOR (OPTIONAL). Accepts bills of various denominations, depending upon the type of bill validator, and how the machine is configured.

SERVICE KEYPAD. The service keypad is located at the top of the monetary panel. It gives service personnel the means to program, retrieve data from, and view diagnostic information about, the merchandiser.

4800006

4

December 2004

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Page Table of Contents Table of Contents December Iii 4800006 Table of Contents Exterior View IntroductionInterior View Unpack the Machine Power RequirementsControls and Indicators Heartbeat Normal ConditionsTurn the Merchandiser on and OFF Remove the Bottom and Top Panels Moving the Merchandiser Through a Narrow DoorwayReassemble the Merchandiser Move the Merchandiser through the OpeningPosition the Merchandiser Open the Rear Outlet DiffuserConfigure Machine for Dual Zone Set machine for two tray configuration version Initial Set-Up Set the machine for three tray configuration version Initial Set-Up Refreshment Center Operators’ Guide Version 2 Duct System See Figure , , on Place a Tray in the Loading Position Tray Set-UpSet Up a Tray To Vend Wide Products Set up Trays to Vend ProductsRemove a Snack or Candy Tray Rear of Tray Remove a Bottle Tray Operate a Tray Outside of the Machine Remove and Install Column DividersReplace a Motor with a Spiral Bearing Remove the motor. See Remove and Install a Spiral Motor onRemove a Motor See Connect and Disconnect a Motor Harness onConnect and Disconnect a Motor Harness Disconnect a Motor HarnessConnect a Motor Harness Spiral Retainer Count Color Assembly Remove and Install SpiralsRemove a Spiral Coupler To Install a SpiralTo Remove a Spiral Choose a Clockwise or Counterclockwise SpiralRemove and Install a Spiral Motor Install a Spiral MotorRemove a Spiral Motor Install a Gear Use a Gear whenPosition the Gear When Used with a Motor Install a Spiral CouplerWhen Used with a Coupler Bearing Spiral Coupler OrientationMove a Tray Up or Down See Install a Tray in the Merchandiser onInstall a Tray in the Merchandiser Install a Product Spacer Install and Remove a Product SpacerAdjust a Product Spacer Remove a Product SpacerGeneral Tray Loading Special ConsiderationsAlso, see Spiral Wall Retainer Usage on Spiral Wall Retainer Usage Product Pusher Usage Configure the Merchandiser to vend Lunch BucketsConfigure the Merchandiser for Vending Top Shelf Return the Trays to the Vending Position Install Price Labels Install and Set Price LabelsInstall the Selection ID Numbers Adjust the Price RollSee the figures below for snack and candy tray positions SureVend Health Control Test the Health Control Health ControlLevel the Merchandiser Final InstallationInstall the Base Plate Install the Optional Cash Box Lock Install the Lock CylinderSet Up the Coin Mechanism Set the Quarter SwitchLoad the Coin Mechanism Operational Readiness Check Spiral Indexing Procedure One Spiral, One MotorTest the Bill Validator Spiral Indexing Procedure Two Spirals, One Or Two MotorsDisplays Programming IntroFunction Keys Other KeysOne Last Thing Diagnostic Messages on Control Panel Switches ExplainedDiagnostics Programming Flow ChartsMisc Supervisor Mode Only Gain Access to the Supervisor ModeEnter a NEW Supervisor Code Enter a Freevend CodeTurn Talker Mode on or OFF Lock or Unlock Mode or Payout KeysAssign a Code to View Data Without Opening the Door UsageSET DEX Options Select DEX or Printer ModeSelect Printer Baud Rate Printer Mode OnlySelect Display Language Select Coin MechanismSelect Bill Validator and Options Setup of a Non-Standard Bill Validator onInitial Setup of a NON-STANDARD Bill Validator Programming Procedures Refreshment Center Operators’ GuideBalance Select Monetary OptionsExample FAIL=WIN-or SET UP Winner ModeAdvanced Options AN ExampleNON-PERISHABLE Food only View or SET Machine ConfigurationEnable or Disable Trays SET Surevend UP the Surevend ANTI-JACKPOT Feature SET UP Basic Surevend OptionsCouple NON-ADJACENT Motors COUPLE/UNCOUPLE Tray MotorsDAY SET Defrost Options Supervisor Mode OnlyPress , then until the display shows Show the Temperature in Standby ModeSee Health Control on View Machine TemperatureView Surevend Software Version View Software VersionSET the Time of DAY SET the DateSET Daylight Savings Option SET TIME-OF-DAY Free Vending SET TIME-OF-DAY Inhibited VendingSET TIME-OF-DAY Discount Vending Time Interval EditingDISCT----K Continue Select a Standby Message Programming Procedures Refreshment Center Operators’ GuideSelect a Freevend Message Select AN OUT-OF-SERVICE MessageEND of Message Character Edit Custom MessagesEntering Your Message JZKSET Prices Payout CoinsSet the Entire Machine to One Price Set All Selections on a Tray to One PriceView Sales Data Three Different Ways View Nonresettable Sales and Vend DataView Card Reader Paid Sales Not shown if total is zeroView Total Paid Vends View Coupon SalesClear Paid Sales Data only View Amount Coin BOXView Amount Validator View Freevend Sales by Time Interval View Discount Sales by Time IntervalView Free Vends View Time Data DecemberHEALTH 2004OFF01/3014.09MAX.69Date and time of the last vend of that selection View Total Unpaid Vends View Total Unpaid SalesView Number of Test Vends View Machine ID NumberView Surevend Data SureemptxxxxTest the Motors Test Vend Selections and Verify Credit AddedView Motor Status by Tray Test the Surevend System SuretstTest the Display DEX Mode OnlyDownload Data to a Pdcd SET Freevend OptionsError Messages View Diagnostic MessagesBoth Eady Screen. See Test the SureVend System on XxnnIndex Refreshment Center Operator’s Guide Index Terms and Conditions of Sale

480 specifications

Crane Merchandising Systems 480 is a versatile vending machine that has redefined the way consumers interact with automated retail. This cutting-edge machine brings a multitude of features, technologies, and characteristics that cater to modern consumer needs while promoting operational efficiency.

One of the primary features of the Crane 480 is its flexible product selection. It is designed to accommodate a wide variety of items, from snacks and beverages to healthier options. With adjustable shelving and configurable product slots, operators can easily tailor the machine’s offerings based on consumer preferences, seasonal trends, or specific location requirements. This adaptability makes it an ideal choice for various environments, including offices, schools, and public spaces.

The Crane 480 employs advanced technology for enhanced user experience. A notable feature is its user-friendly touchscreen interface, which allows customers to browse products seamlessly. The high-resolution display presents vibrant images and product information, making it easier for users to make informed choices. The intuitive interface also supports multiple languages, catering to diverse customer bases.

Another significant aspect is the machine's cashless payment technology. The Crane 480 is equipped to handle various payment methods, including contactless cards, mobile wallets, and even cryptocurrency. This flexibility not only accelerates the transaction process but also meets the growing demand for convenience in payment options.

Energy efficiency is a standout characteristic of the Crane 480. It utilizes LED lighting and energy-saving components, minimizing power consumption without compromising performance. This eco-friendly approach not only reduces operational costs for operators but also aligns with the increasing consumer demand for sustainable practices.

In addition to its operational features, the Crane 480 offers robust remote monitoring capabilities. Through integrated telemetry technology, operators can gain real-time insights into machine performance, inventory levels, and sales data. This information allows for better inventory management and timely restocking, ensuring that popular items are always available, ultimately enhancing customer satisfaction.

Durability is another hallmark of the Crane 480. Constructed with high-quality materials, the machine is designed to withstand the rigors of high-traffic environments while requiring minimal maintenance. Its sleek, modern design also ensures that it fits seamlessly into any location, enhancing the aesthetic appeal of the space.

In summary, Crane Merchandising Systems 480 stands out as a leader in the vending machine industry. Its blend of flexibility, advanced technology, energy efficiency, and durability makes it an excellent choice for both operators and consumers alike. The combination of these features ensures that it not only meets but exceeds the expectations of the vending market in today’s fast-paced world.
Top Page Image Contents