Crane Merchandising Systems 480 manual Sureemptxxxx, View Surevend Data

Page 91

Programming Procedures

Refreshment Center Operators’ Guide

 

 

VIEW SUREVEND™ DATA

Certain SureVend™ data can be viewed if the values are not zero.

1.

Press

, then press

until the display shows

 

. XXXX represents

 

 

 

 

 

Sureemptxxxx

 

the number of times credit was restored or returned because of SureVend™. Press

 

 

to reset this count.

 

 

 

 

2.

Press

. The display shows **

. XXXX represents the total number of

 

SureVend™ corrected vends, viewable by selection. These are vends which normally

 

would not have delivered product if SureVend™ was not in use. Press and hold

 

to reset this count.

 

 

 

 

 

a. Enter a selection letter/number to view the count for that selection.

 

b. Either enter another selection letter/number, or press

to scroll through all

 

selections.

 

 

 

 

 

 

 

NOTE

 

 

 

A high number of corrected vends on a specific selection could indicate that

 

 

the tray is not properly configured for that product.

3.

Press

. The display shows

. XXXX represents the total number of

 

vends, viewable by selection, made.Surewhile SureVend™xxxx

was not in use. Press and hold

 

 

to reset this count.

 

 

 

 

 

a. Enter a selection letter/number to view the count for that selection.

 

b. Either enter another selection letter/number, or press

to scroll through all

 

selections.

wo.Sure

xxxx

 

 

4.

CONTINUE.

 

 

4800006

86

December 2004

Page 90 Page 92
Image 91
Page 90 Page 92
Contents Page Table of Contents Table of Contents December Iii 4800006 Table of Contents Exterior View IntroductionInterior View Unpack the Machine Power RequirementsControls and Indicators Heartbeat Normal ConditionsTurn the Merchandiser on and OFF Remove the Bottom and Top Panels Moving the Merchandiser Through a Narrow DoorwayReassemble the Merchandiser Move the Merchandiser through the OpeningPosition the Merchandiser Open the Rear Outlet DiffuserConfigure Machine for Dual Zone Set machine for two tray configuration version Initial Set-Up Set the machine for three tray configuration version Initial Set-Up Refreshment Center Operators’ Guide Version 2 Duct System See Figure , , on Place a Tray in the Loading Position Tray Set-UpSet Up a Tray To Vend Wide Products Set up Trays to Vend ProductsRemove a Snack or Candy Tray Rear of Tray Remove a Bottle Tray Operate a Tray Outside of the Machine Remove and Install Column DividersSee Connect and Disconnect a Motor Harness on Remove the motor. See Remove and Install a Spiral Motor onReplace a Motor with a Spiral Bearing Remove a MotorDisconnect a Motor Harness Connect and Disconnect a Motor HarnessConnect a Motor Harness Spiral Retainer Count Color Assembly Remove and Install SpiralsChoose a Clockwise or Counterclockwise Spiral To Install a SpiralRemove a Spiral Coupler To Remove a SpiralInstall a Spiral Motor Remove and Install a Spiral MotorRemove a Spiral Motor Use a Gear when Install a GearPosition the Gear Spiral Coupler Orientation Install a Spiral CouplerWhen Used with a Motor When Used with a Coupler BearingMove a Tray Up or Down See Install a Tray in the Merchandiser onInstall a Tray in the Merchandiser Remove a Product Spacer Install and Remove a Product SpacerInstall a Product Spacer Adjust a Product SpacerSpecial Considerations General Tray LoadingAlso, see Spiral Wall Retainer Usage on Spiral Wall Retainer Usage Product Pusher Usage Configure the Merchandiser to vend Lunch BucketsConfigure the Merchandiser for Vending Top Shelf Return the Trays to the Vending Position Install Price Labels Install and Set Price LabelsInstall the Selection ID Numbers Adjust the Price RollSee the figures below for snack and candy tray positions SureVend Health Control Test the Health Control Health ControlLevel the Merchandiser Final InstallationInstall the Base Plate Install the Optional Cash Box Lock Install the Lock CylinderSet the Quarter Switch Set Up the Coin MechanismLoad the Coin Mechanism Operational Readiness Check Spiral Indexing Procedure One Spiral, One MotorTest the Bill Validator Spiral Indexing Procedure Two Spirals, One Or Two MotorsDisplays Programming IntroOther Keys Function KeysOne Last Thing Diagnostic Messages on Control Panel Switches ExplainedDiagnostics Programming Flow ChartsMisc Enter a Freevend Code Gain Access to the Supervisor ModeSupervisor Mode Only Enter a NEW Supervisor CodeUsage Lock or Unlock Mode or Payout KeysTurn Talker Mode on or OFF Assign a Code to View Data Without Opening the DoorSET DEX Options Select DEX or Printer ModeSelect Coin Mechanism Printer Mode OnlySelect Printer Baud Rate Select Display LanguageSelect Bill Validator and Options Setup of a Non-Standard Bill Validator onInitial Setup of a NON-STANDARD Bill Validator Programming Procedures Refreshment Center Operators’ GuideBalance Select Monetary OptionsExample FAIL=AN Example SET UP Winner ModeWIN-or Advanced OptionsNON-PERISHABLE Food only View or SET Machine ConfigurationEnable or Disable Trays SET Surevend UP the Surevend ANTI-JACKPOT Feature SET UP Basic Surevend OptionsCouple NON-ADJACENT Motors COUPLE/UNCOUPLE Tray MotorsDAY SET Defrost Options Supervisor Mode OnlyPress , then until the display shows Show the Temperature in Standby ModeView Software Version View Machine TemperatureSee Health Control on View Surevend Software VersionSET the Date SET the Time of DAYSET Daylight Savings Option Time Interval Editing SET TIME-OF-DAY Inhibited VendingSET TIME-OF-DAY Free Vending SET TIME-OF-DAY Discount VendingDISCT----K Continue Select a Standby Message Programming Procedures Refreshment Center Operators’ GuideSelect a Freevend Message Select AN OUT-OF-SERVICE MessageEND of Message Character Edit Custom MessagesEntering Your Message JZKSet All Selections on a Tray to One Price Payout CoinsSET Prices Set the Entire Machine to One PriceNot shown if total is zero View Nonresettable Sales and Vend DataView Sales Data Three Different Ways View Card Reader Paid SalesView Total Paid Vends View Coupon SalesView Amount Coin BOX Clear Paid Sales Data onlyView Amount Validator View Discount Sales by Time Interval View Freevend Sales by Time IntervalView Free Vends View Time Data DecemberHEALTH 2004OFF01/3014.09MAX.69Date and time of the last vend of that selection View Machine ID Number View Total Unpaid SalesView Total Unpaid Vends View Number of Test VendsView Surevend Data SureemptxxxxTest the Motors Test Vend Selections and Verify Credit AddedView Motor Status by Tray Test the Surevend System SuretstSET Freevend Options DEX Mode OnlyTest the Display Download Data to a PdcdError Messages View Diagnostic MessagesBoth Eady Screen. See Test the SureVend System on XxnnIndex Refreshment Center Operator’s Guide Index Terms and Conditions of Sale

480 specifications

Crane Merchandising Systems 480 is a versatile vending machine that has redefined the way consumers interact with automated retail. This cutting-edge machine brings a multitude of features, technologies, and characteristics that cater to modern consumer needs while promoting operational efficiency.

One of the primary features of the Crane 480 is its flexible product selection. It is designed to accommodate a wide variety of items, from snacks and beverages to healthier options. With adjustable shelving and configurable product slots, operators can easily tailor the machine’s offerings based on consumer preferences, seasonal trends, or specific location requirements. This adaptability makes it an ideal choice for various environments, including offices, schools, and public spaces.

The Crane 480 employs advanced technology for enhanced user experience. A notable feature is its user-friendly touchscreen interface, which allows customers to browse products seamlessly. The high-resolution display presents vibrant images and product information, making it easier for users to make informed choices. The intuitive interface also supports multiple languages, catering to diverse customer bases.

Another significant aspect is the machine's cashless payment technology. The Crane 480 is equipped to handle various payment methods, including contactless cards, mobile wallets, and even cryptocurrency. This flexibility not only accelerates the transaction process but also meets the growing demand for convenience in payment options.

Energy efficiency is a standout characteristic of the Crane 480. It utilizes LED lighting and energy-saving components, minimizing power consumption without compromising performance. This eco-friendly approach not only reduces operational costs for operators but also aligns with the increasing consumer demand for sustainable practices.

In addition to its operational features, the Crane 480 offers robust remote monitoring capabilities. Through integrated telemetry technology, operators can gain real-time insights into machine performance, inventory levels, and sales data. This information allows for better inventory management and timely restocking, ensuring that popular items are always available, ultimately enhancing customer satisfaction.

Durability is another hallmark of the Crane 480. Constructed with high-quality materials, the machine is designed to withstand the rigors of high-traffic environments while requiring minimal maintenance. Its sleek, modern design also ensures that it fits seamlessly into any location, enhancing the aesthetic appeal of the space.

In summary, Crane Merchandising Systems 480 stands out as a leader in the vending machine industry. Its blend of flexibility, advanced technology, energy efficiency, and durability makes it an excellent choice for both operators and consumers alike. The combination of these features ensures that it not only meets but exceeds the expectations of the vending market in today’s fast-paced world.
Top Page Image Contents