Desa SVYD18NRA, SVYD18PRA Installing GAS LOG Into Stove, Connecting to GAS Supply

Page 11

INSTALLATION

Continued

CAUTION: Do not remove the data plates attached to the heater base assembly. The data plates contain important war- ranty and safety information.

WARNING:Failuretoposition thepartsinaccordancewiththese diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

INSTALLING GAS LOG INTO STOVE

1.Remove log from carton.

2.Remove all protective packaging applied to log for shipment.

3.Check log for any shipping damage. If dam- aged (pieces larger than the size of a dime), promptly inform dealer where you bought heater.

4.Set one-piece log on heater base as shown in Figure 12. Make sure middle section at bot- tom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base. IMPORTANT: Make sure log does not cover any burner ports and does not touch the stove cavity (see Figure 13).

5.Fasten back panel to stove with four (4) M6 x 1bolts and washers.

6.Place freestanding stove in desired position in room. Be sure to maintain clearances to combustibles as outlined on page 8.

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs according to the log installation instruc- tions in this manual. Flames con- tacting logs will create soot.

One-Piece

Log Set

Middle

Section at

Bottom of

Log Set

Heater Base

Burner

 

"U" Shaped

Cutout in Chassis

Figure 12 - Installing One-Piece Stove

Log Set

Burner Porting Areas (double slotted rectangular openings)

One-Piece

Log Set

Safety Pilot Location

Figure 13 - Top View of One-Piece Log

Set on Gas Log Heater

CONNECTING TO GAS SUPPLY

WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING:Aqualifiedservice person must connect heater to gassupply.Followalllocalcodes.

CAUTION: Never connect propane/LP heater directly to the propane/LP supply. This heater requires an external regulator (not supplied). Install the exter- nal regulator between the heater and propane/LP supply.

113084-01C

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Victor Hearth OxfordTable of Contents Safety Information Product Identification AIR for Combustion Ventilation Product FeaturesLocal Codes Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationUnusually Tight Construction Confined and Unconfined SpaceVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Minimum Wall and Ceiling Clearances see , InstallationCheck GAS Type Clearances to CombustiblesLift off corrugated box enclosing stove body crating Stove Cavity AssemblyBolt Stop Connecting to GAS Supply Installing GAS LOG Into StoveSide View Installation Items NeededTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures In Excess Of 1/2 Psig 3.5 kPa Lighting Instructions For Your Safety Read Before LightingOperating Heater Shutting Off Heater Ignitor Button Flame Adjustment KnobTo Turn OFF GAS To Appliance ON/OFF Series Model Ghrcb Manual Lighting ProcedureManual Mode Optional HAND-HELD Remote OperationMain Burner Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceObserved Problem Possible Cause Remedy TroubleshootingReplace burner orifice Gas leak. See Warning Observed Problem Possible Cause RemedyModels SVYD18PRA and SVYD18NRA Illustrated Parts BreakdownParts List Oxford Stove Body Victor Hearth Stove KEY Part Number Description QTY Service Hints SpecificationsReplacement Parts Wiring DiagramAccessories Limited Warranty Warranty InformationKeep this Warranty
Top Page Image Contents