Desa S39PT installation manual Inspecting Burners

Page 14

VENT-FREE PROPANE/LP PEDESTAL STOVE

OPERATING

HEATER

Continued

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7, pages 13 and 14. This heater has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again.

8.Turn control knob counterclockwise

C-clockwiseto desired heating level. The burners should light. Set control knob to any heat level between HI and LO.

Pilot Burner

Thermocouple

Figure 23 - Pilot

CAUTION: Do not try to adjust heating levels by using the equip- ment shutoff valve.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise Clockwise to the OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise Clockwise to the PILOT position.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to any comfort level between Hi and Lo. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal com- fort setting will vary by household depend- ing upon the amount of space to be heated, the output of the central heating system, etc.

Note: Selecting the Hi setting with the control knob will cause the burners to remain fully on, without modulating down in most cases.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Light- ing Instructions, page 13.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 in column 1.

OPERATING

OPTIONAL BLOWER

ACCESSORY

Light your gas appliance with the blower off. Turn the blower on to deliver heated air at the top louvers. The blower fea- tures a variable control which allows you to select the speed you desire.

If using the GA3650TA Blower Accessory:

In the ON position, the blower will start when the thermostat senses a sufficient increase in firebox temperature (approxi- mately 10 to 20 minutes depending on heat setting). Note: Your gas stove and thermostat blower will not turn on and off at the same time. The stove may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will con- tinue to run. The blower will shut off after the firebox temperature decreases.

Note: It is safe to operate stove with blower turned off. However, the blower helps distribute heated air from the stove.

Note: Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions.

INSPECTING

BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 24 shows a correct pilot flame pat- tern. Figure 25 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touch- ing the thermocouple. This will cause the thermocouple to cool. When the thermo- couple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 25

•turn heater off (see To Turn Off Gas to Appliance)

•see Troubleshooting, pages 16 through 18

Pilot Burner

Thermocouple

Figure 24 - Correct Pilot Flame Pattern

Pilot Burner

Thermocouple

Figure 25 - Incorrect Pilot Flame Pattern

Continued

For more information, visit www.desatech.com

14

107435

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASSafety Information VENT-FREE PROPANE/LP Pedestal StoveProduct Identification Local Codes Product FeaturesSafety Pilot UnpackingUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Clearances to Combustibles InstallationCheck GAS Type Minimum Wall and Ceiling Clearances see FigureConnecting to GAS Supply Installation Items NeededChecking GAS Connections Pressure Testing Heater Gas ConnectionsPressure Testing Gas Supply Piping System Installing Logs Installing Optional Blower Accessory GA3750Installing Optional Blower Accessory GA3650TA Knob HousingRemoving Cover Plate Lighting Instructions For Your Safety Read Before LightingOperating Heater Inspecting Burners Cleaning and Maintenance Troubleshooting Observed Problem Possible Cause RemedyNance, Top Technical Service SpecificationsService Hints Parts CentralsIllustrated Parts Breakdown S39PTParts List KEY Part Number Description QTY2611 KEY Description QTY Replacement Parts Accessories107435 Warranty Information International

S39PT specifications

Desa S39PT is an innovative solution that stands at the forefront of modern technology and sustainable development. Designed as a multi-functional platform, this advanced system integrates various features aimed at enhancing productivity and efficiency across various sectors, particularly in agricultural and industrial applications.

One of the main characteristics of Desa S39PT is its state-of-the-art automation capabilities. By utilizing artificial intelligence and machine learning algorithms, the platform can analyze vast amounts of data in real-time. This allows users to make informed decisions based on predictive analytics, optimizing processes and reducing waste. Whether for crop management or resource allocation in manufacturing, these technologies enable significant improvements in operational efficiency.

Another noteworthy feature of Desa S39PT is its commitment to sustainability. The platform is equipped with renewable energy technologies, including solar and wind integration, making it a preferred choice for those looking to minimize their carbon footprint. This commitment to green energy not only supports eco-friendly practices but also results in cost savings in the long run.

Desa S39PT also boasts a user-friendly interface, allowing even those with limited technological know-how to navigate the system effortlessly. The platform provides comprehensive training and support resources, ensuring that all users can maximize its potential. Furthermore, its modular design allows for customization according to specific user needs, making it adaptable to various environments and industries.

Connectivity is another vital aspect of Desa S39PT. With robust IoT capabilities, the system enables seamless communication between devices and systems. This interconnectedness facilitates the gathering of data from multiple sources, providing a holistic view of operations and enabling further optimization.

Security is paramount in the design of Desa S39PT. The platform incorporates advanced cybersecurity measures to protect sensitive data, ensuring that users can operate in a trustworthy environment.

In conclusion, Desa S39PT represents a significant advancement in technology, combining automation, sustainability, ease of use, connectivity, and security. This platform is ideal for entities seeking to enhance their operational efficiency while adhering to environmentally responsible practices, marking a progressive step towards a more sustainable future. As industries continue to evolve, solutions like Desa S39PT will play a critical role in meeting the challenges of tomorrow.
Top Page Image Contents