Desa S39PT installation manual Connecting to GAS Supply, Installation Items Needed

Page 8

VENT-FREE PROPANE/LP PEDESTAL STOVE

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.

CAUTION: Never connect heater directly to the propane/LP supply. This heater requires an ex- ternal regulator (not supplied). In- stall the external regulator between the heater and propane/LP supply.

Installation Items Needed

Before installing heater, make sure you have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

sealant (resistant to propane/LP gas)

equipment shutoff valve *

The installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 6. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur.

Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 7).

IMPORTANT: Install equipment shutoff valve in an accessible location. The equip- ment shutoff valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

CAUTION: Use pipe joint seal- ant that is resistant to liquid pe- troleum (LP) gas.

We recommend that you install a sediment trap in supply line as shown in Figure 7. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sedi- ment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

• test gauge connection *

sediment trap

tee joint

pipe wrench

* An CSA design-certified equipment

shutoff valve with 1/8" NPT tap is an ac-

ceptable alternative to test gauge connec-

tion. Purchase the optional CSA design-

certified equipment shutoff valve from your

Propane/LP Supply Tank

External

Regulator

Vent

Pointing

Down

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

dealer. See Accessories, page 24.

Back View

Side View

Front of Stove Unit

Gas Regulator

Inlet Connection

Figure 5 - Gas Regulator Location and Gas Line Access Into Stove Cabinet

Figure 6 - External Regulator With Vent

Pointing Down

From External

 

CSA Design-Certified

Regulator (11"

 

Equipment Shutoff Valve

W.C.** to 14"

 

With 1/8" NPT Tap*

W.C. Pressure)

 

Approved

 

 

 

 

 

 

Flexible Gas

 

 

 

Hose (if allowed

 

 

 

by local codes)

 

Tee

 

 

Sediment

Joint

3" Minimum

 

Trap

Pipe

Gas

 

 

Nipple

 

Regulator

 

Cap

 

of Heater

Figure 7 - Gas Connection

*Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 24.

**Minimum inlet pressure for purpose of input adjustment.

For more information, visit www.desatech.com

8

107435

Image 8
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASSafety Information VENT-FREE PROPANE/LP Pedestal StoveProduct Features Safety PilotProduct Identification Local Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Check GAS TypeClearances to Combustibles Minimum Wall and Ceiling Clearances see FigureConnecting to GAS Supply Installation Items NeededChecking GAS Connections Pressure Testing Heater Gas ConnectionsPressure Testing Gas Supply Piping System Installing Logs Installing Optional Blower Accessory GA3750Installing Optional Blower Accessory GA3650TA Knob HousingRemoving Cover Plate Lighting Instructions For Your Safety Read Before LightingOperating Heater Inspecting Burners Cleaning and Maintenance Troubleshooting Observed Problem Possible Cause RemedyNance, Top Specifications Service HintsTechnical Service Parts CentralsIllustrated Parts Breakdown S39PTParts List KEY Part Number Description QTY2611 KEY Description QTY Replacement Parts Accessories107435 Warranty Information International

S39PT specifications

Desa S39PT is an innovative solution that stands at the forefront of modern technology and sustainable development. Designed as a multi-functional platform, this advanced system integrates various features aimed at enhancing productivity and efficiency across various sectors, particularly in agricultural and industrial applications.

One of the main characteristics of Desa S39PT is its state-of-the-art automation capabilities. By utilizing artificial intelligence and machine learning algorithms, the platform can analyze vast amounts of data in real-time. This allows users to make informed decisions based on predictive analytics, optimizing processes and reducing waste. Whether for crop management or resource allocation in manufacturing, these technologies enable significant improvements in operational efficiency.

Another noteworthy feature of Desa S39PT is its commitment to sustainability. The platform is equipped with renewable energy technologies, including solar and wind integration, making it a preferred choice for those looking to minimize their carbon footprint. This commitment to green energy not only supports eco-friendly practices but also results in cost savings in the long run.

Desa S39PT also boasts a user-friendly interface, allowing even those with limited technological know-how to navigate the system effortlessly. The platform provides comprehensive training and support resources, ensuring that all users can maximize its potential. Furthermore, its modular design allows for customization according to specific user needs, making it adaptable to various environments and industries.

Connectivity is another vital aspect of Desa S39PT. With robust IoT capabilities, the system enables seamless communication between devices and systems. This interconnectedness facilitates the gathering of data from multiple sources, providing a holistic view of operations and enabling further optimization.

Security is paramount in the design of Desa S39PT. The platform incorporates advanced cybersecurity measures to protect sensitive data, ensuring that users can operate in a trustworthy environment.

In conclusion, Desa S39PT represents a significant advancement in technology, combining automation, sustainability, ease of use, connectivity, and security. This platform is ideal for entities seeking to enhance their operational efficiency while adhering to environmentally responsible practices, marking a progressive step towards a more sustainable future. As industries continue to evolve, solutions like Desa S39PT will play a critical role in meeting the challenges of tomorrow.