Trouble Shooting, Problem Possible Cause Solution

Trouble Shooting

Problem	Possible Cause	Solution
Spark will not light	Defective piezo ignitor.	• Check connections to ignitor.
the pilot after		• If ignitor connections are good but no spark,
repeatedly pressing		replace ignitor.
the spark ignitor
the spark ignitor	Broken spark electrode.	• Check for broken ceramic insulation.
		• Replace electrode if broken.
	Low battery or bad	• Replace the electronic module.
	electronic module.	• Replace the battery in module.
	Misaligned spark	• If spark is not arcing from electrode to pilot - adjust
	electrode.	by loosening the screws on the pilot base. Adjust
		away from burner and retighten.

Pilot will not remain	Problem with	• Check for proper connection of the thermocouple to
lit	thermocouple circuit.	the rear of the valve. If loose, fully tighten lightly.
		• Check pilot for full flame impingement around
		thermocouple. If flame is too small, check gas
		pressure, adjust pilot rate screw, check pilot head for
		damage or blockage.
		• Check thermocouple voltage at rear of valve.
		It must be greater than 7 mV. If low, replace
		thermocouple.
	Air in gas line (pilot	• Bleed line.
	dies while knob is	• Check gas line pressure.
	depressed).	• Contact dealer.
Burners will not	Problem with	• Check gas line pressure .
remain lit	thermopile circuit.	• Check for flame impingement on thermopile. If low,
		see “Pilot will not remain lit”.
		• Check thermopile for minimum of 200 mV when
		burner is switched on.
		• Check wiring to thermostat for breaks.
Flame lifting	Leak in vent pipe.	• Check for leaks in vent connections.

	Improper vent	• Check vent configuration with manual.
	configuration.

	Terminal may be	• Check to see if terminal is on correctly.
	recirculating flue gases.	• May need to install high wind termination cap.
		• Contact dealer.

	Improperly set vent	• See venting section for proper restrictor setting.
	restrictor plate.
Glass fogs up	Normal Condition: after the appliance warms up the glass will clear.
	Due to additives in gas, glass may get hazy during operation Clean as
	needed.
Blue Flames	Normal during start up: flames will yellow as the fireplace heats up.

Flames are burning	Flame impingement	• Check log positioning.
“dirty” or sooting		• Check vent restrictor for proper setting.
		• Increase primary air by opening venturi shutter.
		• See also “Burners will not remain lit.”

C-10914 specifications

Enviro C-10914 is a cutting-edge eco-friendly product designed to meet the demands of modern environmental sustainability. With a mission to combat pollution and reduce waste, Enviro C-10914 combines advanced technologies and innovative features to create a robust solution for various applications ranging from industrial processes to home usage.

One of the standout features of Enviro C-10914 is its bio-based composition. Made primarily from renewable resources, this product significantly lowers the carbon footprint compared to traditional counterparts. By utilizing biodegradable materials, it ensures that its lifecycle is more sustainable, addressing the pressing issue of plastic waste in the environment.

Incorporating nanotechnology, Enviro C-10914 enhances its performance through improved durability and resilience. This technology not only increases the longevity of the product but also reduces the need for frequent replacements, promoting a more sustainable consumption model. The nanoscale modifications result in superior resistance to chemicals, UV light, and extreme weather conditions, making it suitable for a variety of applications.

Another key characteristic of Enviro C-10914 is its versatility. It is designed for use in diverse sectors, including agriculture, construction, and consumer goods. In the agricultural sector, for instance, it can be utilized in soil amendments, promoting better crop yield while being safe for both plants and animals. In construction, it serves as an eco-friendly alternative for insulation and waterproofing materials.

The product also features an innovative packaging solution that is user-friendly and minimizes material waste. The design allows for easy handling and application, ensuring that users can maximize its benefits without unnecessary burden.

Additionally, Enviro C-10914 is backed by rigorous testing and certifications that validate its environmental claims. Third-party evaluations confirm its biodegradability and overall effectiveness, providing consumers with confidence in their choices.

In summary, Enviro C-10914 exemplifies the future of sustainable products. With its bio-based materials, nanotechnology enhancements, and versatile applications, it stands at the forefront of eco-innovation, addressing the challenges of pollution and resource depletion in an effective, user-friendly manner. This makes it an essential choice for individuals and businesses alike who are committed to making environmentally responsible decisions.