Enviro FS technical manual Assembling the Face Plate for the FPI and BIH Models, Standard, Built

Page 15

ASSEMBLING THE FACE PLATE FOR THE FPI AND BIH MODELS

1.To attach the pedestal, place the unit on its back, making sure not to damage the wiring, then bolt the pedestal onto the unit. Back off the screws on the base, install the pedestal over the screws. Lock in place using the keyholes, tighten the screws.

2.Assemble the three faceplates to the stove by screwing the hinged panels to the stove side panels. Loosen the front hopper lid screws and center the top panel under the hopper lid, tighten screws. Insert each side panel anchor screw through the top panel into the corresponding side panel holes and tighten.

3.Assemble the brass frame using the corner hardware and screws supplied in the face plate packaging. Install corner hardware into the side brass, then push into the top frame. Do not over-tighten or the side brass cannot be removed during servicing.

4.Place the brass frame over the panel assembly.

5.To access the rear of the stove after the panels are assembled remove side brass and remove the anchor screws from the corresponding side. Swing panel open. Installation is the reverse.

 

Sizing of face plates for FPI:

STANDARD:

40” X 30 ¼”

OVERSIZE: 46” X 33”

BUILT IN:

36” X 32 9/16” OVERSIZE: 46 X 34 ¾”

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents EF-III BAY Installation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataI. Pellet Standards Pellet Quality is Important Please Read the FollowingAutomatic Safety Features of Your Pellet Stove HOW to Start and Operate Your Pellet Appliance Turning Your Pellet Stove OFFSpecial Notes On LOW SLIDER/DAMPER Installation /OPERATION InstructionsInstallation OperationBlower Mechanisms Areas for Routine InspectionASH PAN and Door Gaskets Freestanding ASH PANInside Firebox Post Season CLEAN-UPDoor Glass Fresh AIR IntakeElectrical Component Functions Vacuum Switch 11 F 71C Temperature Sensor12 F 60C N/O Temperature Sensor SHUT-DOWN Sensor 13 F 49C N/C Temperature Sensor Ignitor Shut Down SensorVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet Fireplace DimensionsMasonry Fireplace Insert INSTALLATION, Model FPI Clearance to CombustiblesFireplace Insert Size Assembling the Face Plate for the FPI and BIH Models StandardBuilt Built in Heater Clearances to Combustibles Recommended Framing for Built in HeaterClearances to Combustibles Freestanding Freestanding INSTALLATION, Models FSModel FS Freestanding Installation Pedestal InstallationInstallation Keyholes Here Horizontal Exhaust Through the Wall Through Wall Installation Freestanding Inside Vertical Installation Freestanding Outside Vertical Installation Outside Fresh AIR Connections Mobile Home InstallationTroubleshooting TroubleshootingDo not Page Potentiometer Readings Wiring Diagram Slider Damper Knob Parts ListEF-065 EF-150 Painted For the do-it-yourself Individual Warranty

BIH, FS, FPI specifications

Enviro FPI, FS, and BIH are innovative technologies that have significantly contributed to the field of environmental protection and sustainability. These systems are designed to address various environmental challenges by utilizing advanced features and methodologies that promote efficiency and effectiveness.

The Enviro FPI (Floating Photovoltaic Installation) is a groundbreaking technology that involves the installation of solar panels on bodies of water. This approach not only generates renewable energy but also minimizes land use, which is critical in densely populated areas. The floating structure reduces water evaporation and helps maintain water quality by limiting algae growth. Additionally, the cooling effect of water can enhance the efficiency of solar panels, resulting in higher energy output.

The Enviro FS (Floating System) expands upon the principles of FPI by integrating multiple environmental functionalities. This system includes features such as water filtration and oxygenation, which are essential for improving aquatic ecosystems. The incorporation of bioremediation technologies allows for the natural degradation of pollutants, making it a multifunctional solution for water bodies facing contamination. The FS system is engineered to blend seamlessly into its environment, ensuring minimal disruption to local wildlife and habitats.

The Enviro BIH (Biodegradable Industrial Hemp) represents a leap forward in sustainable materials. Utilizing industrial hemp, this technology creates biodegradable products that can replace conventional plastics. Hemp is known for its fast growth rate and low environmental impact, making it a viable alternative for various industries. The use of BIH not only helps reduce plastic waste but also supports sustainable agriculture and provides economic opportunities for farmers.

All three technologies embody key characteristics that make them stand out in the field of environmental innovation. They are designed with sustainability at their core, emphasizing the importance of balancing human activity with ecological preservation. The integration of renewable energy generation, pollution remediation, and the use of biodegradable materials showcases a holistic approach to modern environmental challenges.

Furthermore, these technologies are scalable and adaptable, allowing for implementation in various contexts, from urban settings to rural areas. As awareness of environmental issues continues to grow, solutions like Enviro FPI, FS, and BIH play an essential role in promoting a greener and more sustainable future for generations to come. Through their combined efforts, these technologies pave the way toward a more responsible relationship with our planet.
Top Page Image Contents