Potentiometer Readings | Enviro BIH, FS, FPI instruction

placing a jumper across the pins. If the auger now cycles very quickly, test the dial-a-fire potentiometer. If the auger did not cycle then replace the timing control module.

-To test the dial-a-fire potentiometer. The potentiometer should have a range of 68K to approximately 850 K (± 10%), if the range is not close then replace the potentiometer.

7.The dial-a-fire has no effect on the fire

-Make sure all connections to the timer control module are secure.

-Perform a resistance test to the dial-a-fire potentiometer, by placing the two test leads from a multimeter into the leads of the potentiometer. The potentiometer should have a range of 68K to approximately 850 K (± 10%).

Potentiometer Readings:

Full counter-clockwise (switched off) = open circuit, overload or Infinite resistance Low fire...................... 800 K to 900 K

High fire..................... 68 K to 82 K

If the range is not close or does not vary then replace the potentiometer.

8.The stove will not shut down

-Check the connections to the 140°F (60°C) temperature sensor, start-up switch and the start-up timer against the wiring diagram.

-Check the 140°F (60°C) temperature sensor by removing one of the brown wires from the sensor. The unit should shut down right away as long as the start button was not pressed within 15 minutes of this test. If the stove shuts down within 15 minutes, replace the 140°F (60°C) sensor. If the stove does not shut down within 15 minutes, test the switch.

-To test the switch, the stove must be cold. Pull the plug, then plug the stove back in. If the fails to start, Replace the switch.

9.The stove keeps going out

-If the stove goes out and leaves fresh un-burned pellets or cigarette-like ashes in the burn pot liner, the fire is going out before the 140°F (60°C) temperature sensor shuts the stove off.

-Check to see that the slider is in the correct position.

-Turn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

-If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove shuts down due to a lack of air, exhaust temperature or power failure.

-Adjust the slider damper.

-Check to see if the stove needs a more complete cleaning.

-Turn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

-Did the power go out?

-If the stove goes out and there are no pellets in the liner, the auger is stopping.

-See “The auger motor will not function normally” and “The exhaust blower will not function normally.”

BIH, FS, FPI specifications

Enviro FPI, FS, and BIH are innovative technologies that have significantly contributed to the field of environmental protection and sustainability. These systems are designed to address various environmental challenges by utilizing advanced features and methodologies that promote efficiency and effectiveness.

The Enviro FPI (Floating Photovoltaic Installation) is a groundbreaking technology that involves the installation of solar panels on bodies of water. This approach not only generates renewable energy but also minimizes land use, which is critical in densely populated areas. The floating structure reduces water evaporation and helps maintain water quality by limiting algae growth. Additionally, the cooling effect of water can enhance the efficiency of solar panels, resulting in higher energy output.

The Enviro FS (Floating System) expands upon the principles of FPI by integrating multiple environmental functionalities. This system includes features such as water filtration and oxygenation, which are essential for improving aquatic ecosystems. The incorporation of bioremediation technologies allows for the natural degradation of pollutants, making it a multifunctional solution for water bodies facing contamination. The FS system is engineered to blend seamlessly into its environment, ensuring minimal disruption to local wildlife and habitats.

The Enviro BIH (Biodegradable Industrial Hemp) represents a leap forward in sustainable materials. Utilizing industrial hemp, this technology creates biodegradable products that can replace conventional plastics. Hemp is known for its fast growth rate and low environmental impact, making it a viable alternative for various industries. The use of BIH not only helps reduce plastic waste but also supports sustainable agriculture and provides economic opportunities for farmers.

All three technologies embody key characteristics that make them stand out in the field of environmental innovation. They are designed with sustainability at their core, emphasizing the importance of balancing human activity with ecological preservation. The integration of renewable energy generation, pollution remediation, and the use of biodegradable materials showcases a holistic approach to modern environmental challenges.

Furthermore, these technologies are scalable and adaptable, allowing for implementation in various contexts, from urban settings to rural areas. As awareness of environmental issues continues to grow, solutions like Enviro FPI, FS, and BIH play an essential role in promoting a greener and more sustainable future for generations to come. Through their combined efforts, these technologies pave the way toward a more responsible relationship with our planet.