Enviro FPI, FS, BIH SLIDER/DAMPER Installation /OPERATION Instructions, Operation, On LOW, On High

Page 7

SLIDER/DAMPER INSTALLATION /OPERATION INSTRUCTIONS

This is used to regulate the airflow through the pellet stove.

INSTALLATION

1.Remove the slider rod (short rod with knob and nuts) and the two nuts from their package and open the left side panel.

2.Remove the knob and outer nut from the knob. Push the rod through the hole in the slider. Place the lock nut on the rod and tighten, leaving a 1/32’ gap between the slider and one of the nuts.

3.Make sure the slider moves freely. Close the side panel and tighten screws after placing the rod through the panel. Screw the knob onto the slider.

OPERATION

-

-

-

ON LOW

Push all the

way in

On the low heat output settings, push the slider all the way in.

On the high heat output pull the slider out or until a good fire is achieved. A good fire is in between a fire with lazy flames (and black tipped flames) and a forced fire (very quick, shorter flames). A good fire is the most efficient and will have a bright and active flame.

Hot magnetic reading 0.10 – 0.11

ON HIGH

Pull out until

an efficient

flame is

achieved

THE TUBE SCRAPER ROD: Put the stainless steel rod through the hole in the heat exchanger, thread the rod into the scraper plate.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents EF-III BAY Installation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataI. Pellet Standards Pellet Quality is Important Please Read the FollowingAutomatic Safety Features of Your Pellet Stove Turning Your Pellet Stove OFF HOW to Start and Operate Your Pellet ApplianceSpecial Notes On LOW SLIDER/DAMPER Installation /OPERATION InstructionsInstallation OperationBlower Mechanisms Areas for Routine InspectionASH PAN and Door Gaskets Freestanding ASH PANInside Firebox Post Season CLEAN-UPDoor Glass Fresh AIR IntakeElectrical Component Functions Vacuum Switch 11 F 71C Temperature Sensor12 F 60C N/O Temperature Sensor SHUT-DOWN Sensor 13 F 49C N/C Temperature Sensor Ignitor Shut Down SensorVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet Fireplace DimensionsClearance to Combustibles Masonry Fireplace Insert INSTALLATION, Model FPIFireplace Insert Size Standard Assembling the Face Plate for the FPI and BIH ModelsBuilt Built in Heater Clearances to Combustibles Recommended Framing for Built in HeaterClearances to Combustibles Freestanding Freestanding INSTALLATION, Models FSPedestal Installation Model FS Freestanding InstallationInstallation Keyholes Here Horizontal Exhaust Through the Wall Through Wall Installation Freestanding Inside Vertical Installation Freestanding Outside Vertical Installation Outside Fresh AIR Connections Mobile Home InstallationTroubleshooting TroubleshootingDo not Page Potentiometer Readings Wiring Diagram Slider Damper Knob Parts ListEF-065 EF-150 Painted For the do-it-yourself Individual Warranty

BIH, FS, FPI specifications

Enviro FPI, FS, and BIH are innovative technologies that have significantly contributed to the field of environmental protection and sustainability. These systems are designed to address various environmental challenges by utilizing advanced features and methodologies that promote efficiency and effectiveness.

The Enviro FPI (Floating Photovoltaic Installation) is a groundbreaking technology that involves the installation of solar panels on bodies of water. This approach not only generates renewable energy but also minimizes land use, which is critical in densely populated areas. The floating structure reduces water evaporation and helps maintain water quality by limiting algae growth. Additionally, the cooling effect of water can enhance the efficiency of solar panels, resulting in higher energy output.

The Enviro FS (Floating System) expands upon the principles of FPI by integrating multiple environmental functionalities. This system includes features such as water filtration and oxygenation, which are essential for improving aquatic ecosystems. The incorporation of bioremediation technologies allows for the natural degradation of pollutants, making it a multifunctional solution for water bodies facing contamination. The FS system is engineered to blend seamlessly into its environment, ensuring minimal disruption to local wildlife and habitats.

The Enviro BIH (Biodegradable Industrial Hemp) represents a leap forward in sustainable materials. Utilizing industrial hemp, this technology creates biodegradable products that can replace conventional plastics. Hemp is known for its fast growth rate and low environmental impact, making it a viable alternative for various industries. The use of BIH not only helps reduce plastic waste but also supports sustainable agriculture and provides economic opportunities for farmers.

All three technologies embody key characteristics that make them stand out in the field of environmental innovation. They are designed with sustainability at their core, emphasizing the importance of balancing human activity with ecological preservation. The integration of renewable energy generation, pollution remediation, and the use of biodegradable materials showcases a holistic approach to modern environmental challenges.

Furthermore, these technologies are scalable and adaptable, allowing for implementation in various contexts, from urban settings to rural areas. As awareness of environmental issues continues to grow, solutions like Enviro FPI, FS, and BIH play an essential role in promoting a greener and more sustainable future for generations to come. Through their combined efforts, these technologies pave the way toward a more responsible relationship with our planet.
Top Page Image Contents