Enviro FS, FPI, BIH technical manual Freestanding Inside Vertical Installation

Page 21

FREESTANDING INSIDE VERTICAL INSTALLATION

1.Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance.

2.Place a non-combustible hearth pad where necessary.

3.Place the unit on the hearth pad and space it in a manner so when the pellet vent is installed vertically, it will be 3” (76 mm) away from a combustible wall.

4.Locate the center of the fresh air intake pipe on the unit. Match that center with the same point on the wall and cut a hole about 1 5/8” (41 mm) in diameter.

5.Install the fresh air intake pipe.

6.Install the tee with clean out.

7.Install the pellet vent upward from there. When you reach the ceiling make sure that the vent goes through the ceiling firestop. Maintain a 3” (76 mm) distance to combustibles and keep attic insulation away from the pipe.

8.Finally, extend the pellet vent to go through the roof flashing.

9.Ensure that the rain cap is approximately 36” (900 mm) above the roof.

Image 21

Contents EF-III BAY Installation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataI. Pellet Standards Pellet Quality is Important Please Read the FollowingAutomatic Safety Features of Your Pellet Stove HOW to Start and Operate Your Pellet Appliance Turning Your Pellet Stove OFFSpecial Notes Installation SLIDER/DAMPER Installation /OPERATION InstructionsOperation On LOWASH PAN and Door Gaskets Areas for Routine InspectionFreestanding ASH PAN Blower MechanismsDoor Glass Post Season CLEAN-UPFresh AIR Intake Inside FireboxElectrical Component Functions 12 F 60C N/O Temperature Sensor SHUT-DOWN Sensor 11 F 71C Temperature Sensor13 F 49C N/C Temperature Sensor Ignitor Shut Down Sensor Vacuum SwitchVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet Fireplace DimensionsMasonry Fireplace Insert INSTALLATION, Model FPI Clearance to CombustiblesFireplace Insert Size Assembling the Face Plate for the FPI and BIH Models StandardBuilt Built in Heater Clearances to Combustibles Recommended Framing for Built in HeaterClearances to Combustibles Freestanding Freestanding INSTALLATION, Models FSModel FS Freestanding Installation Pedestal InstallationInstallation Keyholes Here Horizontal Exhaust Through the Wall Through Wall Installation Freestanding Inside Vertical Installation Freestanding Outside Vertical Installation Outside Fresh AIR Connections Mobile Home InstallationTroubleshooting TroubleshootingDo not Page Potentiometer Readings Wiring Diagram Slider Damper Knob Parts ListEF-065 EF-150 Painted For the do-it-yourself Individual Warranty

BIH, FS, FPI specifications

Enviro FPI, FS, and BIH are innovative technologies that have significantly contributed to the field of environmental protection and sustainability. These systems are designed to address various environmental challenges by utilizing advanced features and methodologies that promote efficiency and effectiveness.

The Enviro FPI (Floating Photovoltaic Installation) is a groundbreaking technology that involves the installation of solar panels on bodies of water. This approach not only generates renewable energy but also minimizes land use, which is critical in densely populated areas. The floating structure reduces water evaporation and helps maintain water quality by limiting algae growth. Additionally, the cooling effect of water can enhance the efficiency of solar panels, resulting in higher energy output.

The Enviro FS (Floating System) expands upon the principles of FPI by integrating multiple environmental functionalities. This system includes features such as water filtration and oxygenation, which are essential for improving aquatic ecosystems. The incorporation of bioremediation technologies allows for the natural degradation of pollutants, making it a multifunctional solution for water bodies facing contamination. The FS system is engineered to blend seamlessly into its environment, ensuring minimal disruption to local wildlife and habitats.

The Enviro BIH (Biodegradable Industrial Hemp) represents a leap forward in sustainable materials. Utilizing industrial hemp, this technology creates biodegradable products that can replace conventional plastics. Hemp is known for its fast growth rate and low environmental impact, making it a viable alternative for various industries. The use of BIH not only helps reduce plastic waste but also supports sustainable agriculture and provides economic opportunities for farmers.

All three technologies embody key characteristics that make them stand out in the field of environmental innovation. They are designed with sustainability at their core, emphasizing the importance of balancing human activity with ecological preservation. The integration of renewable energy generation, pollution remediation, and the use of biodegradable materials showcases a holistic approach to modern environmental challenges.

Furthermore, these technologies are scalable and adaptable, allowing for implementation in various contexts, from urban settings to rural areas. As awareness of environmental issues continues to grow, solutions like Enviro FPI, FS, and BIH play an essential role in promoting a greener and more sustainable future for generations to come. Through their combined efforts, these technologies pave the way toward a more responsible relationship with our planet.