Enviro C-11112, 50-1266 owner manual Routine Cleaning and Maintenance, Tools Required to Clean Unit

Page 10

Routine Cleaning and Maintenance

The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its optimum and giving you excellent heat value:

2-3 Days / Weekly

Semi-annually or 2 Tons of Fuel

Burn Pot and Liner

Exhaust Vent

Ash Pan

Fresh air Intake Tube

Inside Firebox

Blower Mechanisms

Door Glass

Heat exchanger tubes

Heat exchanger tubes

Behind firebox liners

Ash pan and Door gaskets

All Hinges

Door Latch

Post Season Clean-up

TOOLS REQUIRED TO CLEAN UNIT

 

• Torx T-20 Screwdriver

• Brush

• Soft Cloth

5/16” Wrench or Socket

• Vacuum with fine filter bag

BURN POT AND LINER (2-3 days)

Burn Pot Liner

Ignitor

Air Intake

Tube

Burn Pot

Figure 5: Burn pot assembly.

Cleaning of the burn pot and liner must only be done when stove is cold. To remove the burn pot and burn pot liner, open the door using the door handle provided (located on the right-hand side of the stove). Swing the door open. Lift the liner from the burn pot. Lift the burn pot from the firebox by gently lifting up the front of the burn pot, then sliding the assembly from the air intake tube and the ignitor cartridge.

This is the ‘pot’ where the pellets are burned. Every two to three days (when the unit is cold), remove the burn-pot liner from the stove and inspected it to ensure proper air flow through the liner. Failure to keep the liner clean may cause a build up of fuel past the burn pot liner and up the drop tube. This will cause the auger to jam and may result in pellets burning in the drop tube and hopper. Using a metal scrapper, remove material that has accumulated or is clogging the liner’s holes. Then dispose of the scrapped ashes from the liner and from inside the burn-pot. Place the burn-pot back into the stove, making sure that the pipes are properly inserted into the burn pot. Place the liner back into the burn-pot, making sure that the ignitor hole in the liner is aligned with the ignitor tube. Pushing the liner up against the ignitor tube.

If, after long periods of burning, the fire continually builds up and overflows the burn pot or there is a build up of clinkers, this is an indication that the pellet fuel quality is poor or the stove may need cleaning. Check the stove for ash build up (clean if required) and adjust the slider / damper to produce the proper clean combustion.

DOOR LATCH (2-3 days)

Check the door latch every time the door is opened or closed to ensure proper movement.

DOOR GLASS CLEANING (When needed)

Cleaning of the glass must only be done when stove is cold. Open the door by lifting the handle. The glass can be cleaned by wiping down the outside and inside of the glass with a dry soft cloth.

If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass.

10

Image 10
Contents Empress Table of Contents Introduction Store pellets at least 36 1 m away from the pellet stoveUSE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Specifications Empress DimensionsOperating Instructions Slider / Damper Must be SET AT Time of InstallationSpecial Notes Heat Output Indicator Shows Heat Level Adjustment WhenThermostat / Switch Mode Initial START-UP See aboveDoor Glass Cleaning When needed Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysDo not Place Unburned or RAW Pellet Fuel in ASH PAN Firebox Panel Post Season CLEAN-UPCleaning Surfaces Replacing Door GlassTo the Distributor WarrantyFor the do-it-yourself Individual Installation Data Sheet Name of Owner Address

C-11112, 50-1266 specifications

Enviro 50-1266, also known by its designation C-11112, is a cutting-edge product that stands out in the realm of environmentally friendly solutions. It is designed with a focus on sustainability while delivering high performance in various applications. One of its main features is its biodegradable composition, which significantly reduces environmental impact compared to traditional products. This aspect appeals to both consumers and businesses looking to adopt greener practices.

The product is formulated using advanced technologies that enhance its effectiveness. One of these technologies involves the incorporation of bio-based materials that exhibit exceptional durability and resistance to degradation. This ensures that the product maintains its integrity over time, even in challenging environments, while still being safe for the ecosystem.

Furthermore, Enviro 50-1266 features a unique formulation that allows for versatile usage across different sectors, from agriculture to industrial applications. Whether used as a cleaner, lubricant, or in manufacturing processes, its performance remains consistent and reliable. Additionally, the product is designed to be user-friendly, facilitating easy application without the need for specialized equipment or extensive training.

Another noteworthy characteristic of Enviro 50-1266 is its non-toxic nature, making it suitable for use around children and pets. This feature broadens its appeal, particularly among environmentally conscious consumers and organizations. The product not only meets but often exceeds regulatory standards for safety and environmental compliance, further establishing its credibility in the market.

In terms of customer support, the manufacturers provide comprehensive resources, including detailed guidelines for optimal use and applications. They also offer responsive customer service to address any inquiries or concerns, which enhances the overall user experience.

In summary, Enviro 50-1266, C-11112, is a versatile, sustainable solution that excels in various applications while prioritizing environmental responsibility. Its biodegradable composition, advanced manufacturing technologies, and user-friendly characteristics make it a notable choice for those seeking effective and eco-friendly alternatives. With a commitment to safety and compliance, this product not only meets modern demands but also contributes positively to the preservation of our planet.