Enviro 1200, 1700 owner manual Roof Clearances

Page 23

Installation

INSTALLATION OF A LISTED, FACTORY BUILT CHIMNEY - FREESTANDING:

This is a generic set of instructions; always follow the chimney manufacturer’s instructions explicitly. Also refer to “RECOMMENDED HEIGHTS FOR FLUE PIPE”.

1.Set floor protector and stove in location in accordance with the “CLEARANCES TO COMBUSTIBLES - 1200

FREESTANDING” or “CLEARANCES TO COMBUSTIBLES - 1700 FREESTANDING”.

2.Mark the position for the ceiling hole by suspending a plumb bob from the ceiling over the exact center of your stove flue and mark a spot on the ceiling to indicate the center of the chimney.

3.Move this location, if necessary, to avoid floor joists, ceiling rafters, electrical wiring and plumbing while still maintaining required clearances. If floor joists or ceiling rafters must be cut they must be made structurally sound again. Install chimney according to chimney manufacturers instructions. A chimney connector cannot pass through an attic or roof space, closet or similar concealed space, or a floor, ceiling, wall or partition of combustible construction. In Canada, if passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365 Installation Code for Solid- Fuel Burning Appliances and Equipment and NFPA 211 Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances.

4.Mark the hole for the outside air kit.

5.Move the stove out of the way.

6.Cut a pilot hole in the ceiling.

7.Cut a hole for the ceiling penetration components and frame in the sides of the hole in both the ceiling and roof. Check, and follow chimney manufacturer’s instructions for all of these steps.

8.Install the support box and chimney through the roof. Install the slip section for the chimney connector.

9.Slip the roof flashing over the chimney and secure to the roof, being careful to keep the pipe centered in the opening. To meet the code, the chimney must extend above the roof penetration at least 3 feet (91.4 cm), and in any area within 10 feet (304.8 cm) of the roof

Figure 22: Roof Clearances.

 

Rain cap/

 

Spark arrestor cap

 

Storm Collar

 

Roof flashing

 

Roof

Insulated chimney

Attic

 

radiation shield

Ceiling

Radiation shield

Ceiling support

 

Minimum air space in

 

accordance with

 

chimney manufacturer.

 

 

Chimney

 

connector

 

Woodstove

Optional

 

fan

 

 

Pedestal

 

Hearthpad

Outside air connection

Floor

through wall or floor

 

Figure 23: Standard Vertical Installation.

23

Image 23
Contents Wood Stove Table of Contents Safety Precautions First Start Operating InstructionsCreosote ITS Formation and Removal Helpful Hints Worth Repeating What type of wood is best to use as firewood? What can cause a poor draft? 1200 Air Flow Path Specifications Capacity Feet3 0.0708 meter3 Approximate heating area † From front of unit to edge of floor protection Maintain These Minimum Clearances to Unshielded Combustibles 1700 Freestanding Clearance to Combustibles 1200 Insert Dimensions 1200 Freestanding Flat Top Dimensions 1700 Freestanding Flat Top Dimensions 1200 Freestanding with Fan Kit Dimensions Bolts to remove InstallationInstalling Heat Shield Recommended Height for Flue Pipe Chimney Through Wall Method a Roof Clearances Shield if required Installation into a masonry chimney Venting Outside AIR Insert Installation into existing fireplace with Hearth Metal TAG this Fireplace has Been Before starting this type of installation 3D of Dimensions needed from Fireplace Insert Install into a Zero-Clearance Fireplace Total Bricks Model 1700 Brick Placement Do not USE Door if Glass is Broken Installation of Ceramic Baffle Back View of Freestanding Unit with Fan Kit Removal of right pod This will keep the trim tight Parts List Parts List Parts Diagram Parts Diagram Pedestals & Legs Parts Diagram Fireplace Insert Limited Five 5 Year Warranty Limited One 1 Year Warranty WarrantyExclusions and Limitations Warranty Installation Data Sheet

1700, 1200 specifications

The Enviro 1200 and 1700 are innovative solutions in the world of air treatment and environmental control. Designed to cater to industrial and commercial needs, these models are pivotal in enhancing air quality and promoting energy efficiency.

One of the main features of the Enviro 1200 is its advanced filtration system. It utilizes a multi-stage filtration process that includes pre-filters, HEPA filters, and activated carbon filters. This combination ensures the capture of particulate matter, volatile organic compounds (VOCs), and other airborne contaminants, providing cleaner and healthier air. The Enviro 1700, while similar in filtration capabilities, boasts a larger capacity, making it suitable for bigger spaces or industrial applications.

Both models incorporate smart sensor technologies that monitor air quality in real-time. These sensors provide data on pollutant levels, allowing for dynamic adjustments to the filtration strength. This not only optimizes performance but also reduces energy consumption, making the Enviro series both eco-friendly and cost-effective. The adaptive response of these systems ensures that users always breathe cleaner air without unnecessary energy expenditure.

Another defining characteristic of the Enviro 1200 and 1700 is their user-friendly interface. These units are designed with digital controls, allowing for easy programming and monitoring. Users can set specific operating schedules and track air quality trends over time. Additionally, both models come equipped with WiFi connectivity, enabling remote control via a smartphone app. This feature allows users to adjust settings or receive alerts about air quality levels from anywhere.

In terms of durability, both the Enviro 1200 and 1700 are constructed with high-quality materials that ensure long-lasting performance. They are designed to operate quietly, reducing the noise levels often associated with air treatment systems. This makes them suitable for a range of environments, from offices and homes to industrial settings.

In summary, the Enviro 1200 and 1700 stand out in the air treatment market due to their state-of-the-art filtration, smart technology integration, and user-centric design. These features, combined with their robust build quality, make them a reliable choice for anyone looking to improve air quality while maintaining energy efficiency.