Desa Tech CSNPT Inspecting Burners, Thermostat Control Operation, Manual Lighting Procedure

Page 12
C-clockwise

12

OPERATING HEATER

Lighting Instructions (Cont.)

To Turn Off Gas To Appliance

Thermostat Control Operation

Manual Lighting Procedure

INSPECTING BURNERS

OPERATING HEATER

Continued

Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will al- low air to bleed from the gas system.

6.With control knob pressed in, press and release ignitor but- ton. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, column 2.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute for sys- tem to reset before lighting pilot again.

8. Turn control knob counterclockwise to desired heat- ing level. The burners should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to any comfort level between HI and LO. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

Note: Selecting the HI setting with the control knob will cause the burner to remain fully on, without modulating down in most cases.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 11.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 in Lighting Instructions, column 1.

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

Ignitor Button

Control Knob

Figure 16 - Control Knob and Ignitor Button Location

Pilot Burner

Thermocouple

Figure 17 - Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise Clockwise to the OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise Clockwise to the PILOT position.

PILOT FLAME PATTERN

Figure 18 shows a correct pilot flame pattern. Figure 19 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 19

•turn heater off (see To Turn Off Gas to Appliance, column 1)

•see Troubleshooting, pages 14 through 16

Note: The pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color.

Pilot Burner

Pilot Burner

Thermocouple

Thermocouple

 

Figure 18 - Correct Pilot Flame

Figure 19 - Incorrect Pilot Flame

Pattern (Propane/LP Shown)

Pattern (Propane/LP Shown)

For..com

111487-01A

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Csbnt Csnpt Cspbnt Cspbpt Cspint Cspipt What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Typical Stove Cabinet Model with Comfort Glow Gas Log HeaterProduct Features Local CodesAIR for Combustion and Ventilation Determining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingInstallation UnpackingVentilation Air From Outdoors Stove TOPCheck GAS Type Clearances to Combustibles Vent-Free Operation OnlyMinimum Wall and Ceiling Clearances see Figure Connecting to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Checking GAS ConnectionsInstalling ROD and Screen Pressure Testing Heater Gas ConnectionsInstalling LOG SET For Your Safety Read Before LightingOperating Heater Lighting InstructionsManual Lighting Procedure Inspecting BurnersThermostat Control Operation To Turn OFF GAS To ApplianceCleaning Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleMain Burner LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Maintenance,Top Specifications Service HintsTechnical Service AccessoriesIllustrated Parts Breakdown Models SL30PT and SL30NTParts List KEY Part Number SL30PT SL30NT Description QTYStove Body Models CSB SERIES, Cspb Series Cspi Series KEY Part Number Description QTY Parts Centrals FBDOwners Registration Form Postage Required 111487-01A Warranty Information

CSNPT specifications

Desa Tech CSNPT is an innovative technology platform that brings together cutting-edge features and capabilities to enhance performance in diverse industries. Designed for adaptability and efficiency, CSNPT stands for Customer Service Network Platform Technology, which serves as a vital tool for businesses looking to improve their customer support systems.

One of the main features of Desa Tech CSNPT is its advanced analytics capabilities. The platform integrates data visualization tools that allow organizations to gain insights into customer interactions and service performance. This information can be utilized to optimize workflows, improve response times, and enhance overall customer satisfaction. By leveraging historical data and real-time metrics, businesses can make informed decisions aimed at driving operational efficiency.

Another key characteristic of the CSNPT platform is its modular architecture. This flexibility enables companies to customize their customer service solutions according to specific needs. Organizations can easily add or modify components to create a tailored experience that aligns with their unique requirements. Whether it involves integrating new communication channels, implementing AI-powered chatbots, or automating routine tasks, businesses can scale their operations without significant overhead.

The use of artificial intelligence and machine learning is a standout feature of the Desa Tech CSNPT. These technologies enhance the platform's efficiency by automating repetitive processes and providing intelligent recommendations to support staff. For instance, AI-driven chatbots can handle customer inquiries 24/7, freeing up human agents to address more complex issues. This not only improves response times but also allows businesses to serve a larger volume of customers simultaneously.

Security is another fundamental aspect of CSNPT. Given the sensitive nature of customer data, the platform employs robust security measures, including end-to-end encryption and multi-factor authentication. By prioritizing data protection, businesses can build trust with their customers while ensuring compliance with regulations.

Overall, Desa Tech CSNPT offers a comprehensive solution that merges advanced technologies with customizable features. By empowering organizations to enhance their customer service operations, the platform paves the way for improved customer experiences and operational success. Its flexibility, analytical prowess, AI integration, and strong security make it a preferred choice for businesses seeking to innovate in customer engagement.
Top Page Image Contents