Desa Tech CSNPT Checking GAS Connections, Pressure Testing Gas Supply Piping System

Page 9

INSTALLATION

Connecting to Gas Supply (Cont.) Checking Gas Connections

9

INSTALLATION

Continued

WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

We recommend that you install a sediment trap in supply line as shown in Figure 8. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

 

CSA Design-Certified

From External

Equipment Shutoff Valve

With 1/8" NPT Tap*

Regulator (11"

Approved Flexible

W.C.** to 14"

W.C. Pressure)

Gas Hose (if allowed

 

by local codes)

 

 

3" Minimum

Gas

 

 

Regulator

Tee

Pipe

Cap

(Propane/LP)

Joint

Nipple

 

 

Sediment Trap

Figure 8 - Gas Connection

*Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 17.

**Minimum inlet pressure for purpose of input adjustment.

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

CAUTION: Make sure external regulator has been installed between propane/LP supply and propane/ LP heater. See guidelines under Connecting to Gas Supply, page 8.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1.Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping sys- tem. Pressures in excess of 1/2 psig will damage heater regulator.

2.Cap open end of gas pipe where equipment shutoff valve was connected.

3.Pressurize supply piping system by either opening propane/ LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air.

4.Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1.Close equipment shutoff valve (see Figure 9).

2.Pressurize supply piping system by either opening propane/ LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air.

3.Check all joints from gas meter for natural or propane/LP sup- ply to equipment shutoff valve (see Figure 10 or 11, page 10). Apply noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.

4.Correct all leaks at once.

Open

Equipment

Shutoff

Valve

CO losed

POS

Figure 9 - Equipment Shutoff Valve

For morevisit www..com

111487-01A

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS Csbnt Csnpt Cspbnt Cspbpt Cspint CspiptSafety Information Table of ContentsTypical Stove Cabinet Model with Comfort Glow Gas Log Heater Product IdentificationProduct Features Local CodesAIR for Combustion and Ventilation Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation AIR Ventilation Air From Inside BuildingUnpacking InstallationVentilation Air From Outdoors Stove TOPCheck GAS Type Clearances to Combustibles Vent-Free Operation OnlyMinimum Wall and Ceiling Clearances see Figure Installation Items Needed Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Heater Gas Connections Installing ROD and ScreenFor Your Safety Read Before Lighting Installing LOG SETOperating Heater Lighting InstructionsInspecting Burners Manual Lighting ProcedureThermostat Control Operation To Turn OFF GAS To ApplianceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceMain Burner LogsObserved Problem Possible Cause TroubleshootingMaintenance, Observed Problem Possible Cause RemedyTop Service Hints SpecificationsTechnical Service AccessoriesModels SL30PT and SL30NT Illustrated Parts BreakdownKEY Part Number SL30PT SL30NT Description QTY Parts ListStove Body Models CSB SERIES, Cspb Series Cspi Series KEY Part Number Description QTY FBD Parts CentralsOwners Registration Form Postage Required 111487-01A Warranty Information

CSNPT specifications

Desa Tech CSNPT is an innovative technology platform that brings together cutting-edge features and capabilities to enhance performance in diverse industries. Designed for adaptability and efficiency, CSNPT stands for Customer Service Network Platform Technology, which serves as a vital tool for businesses looking to improve their customer support systems.

One of the main features of Desa Tech CSNPT is its advanced analytics capabilities. The platform integrates data visualization tools that allow organizations to gain insights into customer interactions and service performance. This information can be utilized to optimize workflows, improve response times, and enhance overall customer satisfaction. By leveraging historical data and real-time metrics, businesses can make informed decisions aimed at driving operational efficiency.

Another key characteristic of the CSNPT platform is its modular architecture. This flexibility enables companies to customize their customer service solutions according to specific needs. Organizations can easily add or modify components to create a tailored experience that aligns with their unique requirements. Whether it involves integrating new communication channels, implementing AI-powered chatbots, or automating routine tasks, businesses can scale their operations without significant overhead.

The use of artificial intelligence and machine learning is a standout feature of the Desa Tech CSNPT. These technologies enhance the platform's efficiency by automating repetitive processes and providing intelligent recommendations to support staff. For instance, AI-driven chatbots can handle customer inquiries 24/7, freeing up human agents to address more complex issues. This not only improves response times but also allows businesses to serve a larger volume of customers simultaneously.

Security is another fundamental aspect of CSNPT. Given the sensitive nature of customer data, the platform employs robust security measures, including end-to-end encryption and multi-factor authentication. By prioritizing data protection, businesses can build trust with their customers while ensuring compliance with regulations.

Overall, Desa Tech CSNPT offers a comprehensive solution that merges advanced technologies with customizable features. By empowering organizations to enhance their customer service operations, the platform paves the way for improved customer experiences and operational success. Its flexibility, analytical prowess, AI integration, and strong security make it a preferred choice for businesses seeking to innovate in customer engagement.
Top Page Image Contents