Breckwell P4000 Stove Feeds PELLETS, but will not Ignite, Possible Causes Possible Remedies

Page 21

TROUBLESHOOTING GUIDE

21

STOVE FEEDS PELLETS, BUT WILL NOT IGNITE

Possible Causes:

Possible Remedies:

 

 

 

1.

Air damper open too far for ignition.

Push the air damper in closer to the side of the stove for startup. In

 

 

some situations it may be necessary to have the damper completely

 

 

closed for ignition to take place. After there is a flame, the damper

 

 

can then be adjusted for the desired feed setting.

 

 

 

2.

Blockage in igniter tube or inlet for igniter tube.

Find the igniter housing on the backside of the firewall. The air

 

 

intake hole is a small hole located on bottom side of the housing.

 

 

Make sure it is clear. Also, look from the front of the stove to make

 

 

sure there is not any debris around the igniter element inside of the

 

 

igniter housing.

 

 

 

3.

The burnpot is not pushed completely to the rear of the firebox.

Make sure that the air intake collar on the burnpot is touching the

 

 

rear wall of the firebox.

 

 

 

4.

Bad igniter element.

Put power directly to the igniter element. Watch the tip of the igniter

 

 

from the front of the stove. After about 2 minutes the tip should

 

 

glow. If it does not, the element is bad.

 

 

 

5.

The control board is not sending power to the igniter.

Check the voltage going to the igniter during startup. It should be a

 

 

full current. If the voltage is lower than full current, check the wiring.

 

 

If the wiring checks out good, the board is bad.

 

 

 

 

SMOKE SMELL COMING BACK INTO THE HOME

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

There is a leak in the vent pipe system.

 

 

 

Inspect all vent pipe connections. Make sure they are sealed with

 

 

RTV silicone that has a temperature rating on 500 degree F or

 

 

higher. Also, seal joints with UL-181-AP foil tape. Also, make sure

 

 

the square to round adapter piece on the combustion blower has

 

 

been properly sealed with the same RTV.

 

 

 

2.

The gasket on the combustion blower has gone bad.

 

 

 

Inspect both gaskets on the combustion blower to make sure they

 

 

are in good shape.

 

 

 

 

CONVECTION BLOWER SHUTS OFF AND COMES BACK ON

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

The convection blower is overheating and tripping the internal

Try lubricating the convection blower. Put 1-2 drops of SAE 20 oil in

 

temperature shutoff.

each of the two oiling ports. Also, clean any dust off of the windings

 

 

and fan blades. If oiling the blower does not help, the blower may

 

 

be bad.

 

 

 

2.

Circuit board malfunction.

Test the current going to the convection blower. If there is power

 

 

being sent to the blower when it is shut off, then the control board is

 

 

fine. If there is NOT power being sent to the blower when it shuts off

 

 

during operation, then you have a bad control board.

 

 

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Vermont Important Information IntroductionSafety Precautions Table of Contents Specifications InstallationPreparation ClearancesWhen Outside AIR is not Used Combustion AIR SupplyVenting P4000 Installation Equivalent Vent Length EVLHorizontally Through Wall refer to Figure Vertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureVertically Into Existing Masonry Fireplace Installation Through Side of Masonry ChimneySpecial Mobile Home Requirements Electrical InstallationOperation PRE-START-UP Check Proper FuelBuilding a Fire Hotrod Automatic FirestarterShutdown Procedure Breckwell Maintenance ToolSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat Millivolt Thermostat is RequiredPlease Read this ASH Removal MaintenanceASH Disposal Vacuum USEBlowers CleaningDaily Weekly Annually or per Ton Chimney CleaningTroubleshooting Guide Stove Shuts OFF and the # 2 Light FlashesPossible Causes Stove Shuts OFF and the # 3 Light Flashes Possible Causes Possible Remedies Stove Feeds PELLETS, but will not IgniteSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide Heat Level Setting P4000 High Limit Switch Keeps TrippingSmoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Burnpot Replacement PartsLifetime Limited Warranty

P4000 specifications

The Breckwell P4000 is a pellet stove that combines efficiency, performance, and stylish design, making it an ideal choice for homeowners seeking an eco-friendly heating solution. With its robust construction and advanced technology, the P4000 stands out in a crowded market of heating appliances.

One of the key features of the Breckwell P4000 is its high heating capacity. Designed to heat spaces up to 2,200 square feet, it has a maximum output of 40,000 BTUs. This makes it suitable for both small and large rooms, providing a comfortable environment even in the coldest months. The stove also includes a large hopper capacity, able to hold up to 60 pounds of pellets, allowing for longer burn times without the need for constant refueling.

The P4000 is equipped with an advanced digital control panel. This user-friendly interface allows homeowners to easily adjust the thermostat and control the flame intensity, ensuring an optimal heating experience. Additionally, it features an automatic igniter for hassle-free start-up, allowing users to ignite their stove with the push of a button.

Efficiency and environmental performance are cornerstones of the Breckwell P4000's design. The stove boasts an impressive efficiency rating of up to 87%, meaning that minimal heat is lost during operation. This efficiency not only leads to lower heating bills but also reduces the environmental impact, as pellet stoves are considered a renewable energy source.

The P4000 also emphasizes safety, featuring a list of safety controls including a heat sensor and an automatic shut-off function. This ensures peace of mind for users, as it reduces the risk of overheating or fire hazards.

Another appealing aspect of the Breckwell P4000 is its aesthetic versatility. The stove comes in various finishes, including traditional black and modern stainless steel, allowing it to seamlessly integrate into various home decors. Its compact design ensures it can fit into tight spaces while still delivering powerful heating performance.

In conclusion, the Breckwell P4000 pellet stove combines modern technology, high efficiency, and attractive design. Its powerful heating capabilities, user-friendly controls, and safety features make it an excellent choice for homeowners looking for a reliable and stylish heating solution. Whether for a cozy living room or an expansive open space, the P4000 is dedicated to providing warmth and comfort during the cold months.
Top Page Image Contents