Breckwell P4000 owner manual Vertically Into Existing Masonry Fireplace

Page 9

INSTALLATION

9

D.VERTICALLY INTO EXISTING MASONRY FIREPLACE

NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions.

1.Have the masonry chimney inspected by a qualified chimney sweep or installer to determine its structural condition.

2.You will need a pipe length equal to the chimney height from the hearth. If outside combustion air is to be used, you will need a pipe length equal to the chimney height plus 18 inches.

3.Install a blanking plate and the chimney pipe, and if used the outside air pipe, as shown in Figure 9.

4.Attach the L-Vent adapter, a section of pipe and clean out tee, making sure the clean out tee is centered in the chimney flue area.

5.Position the stove, adhering to the clearances in Figures 1 & 2.

6.Measure and build chimney top plate. Cut out holes for chimney pipe, and if used the outside air pipe. Install and seal with non-hardening mastic to prevent water leakage. Install vent cap.

E.INSTALLATION THROUGH SIDE OF MASONRY CHIMNEY

NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions.

1.Position the stove, adhering to the clearances in Figures 1 & 2. Mark the center of the hole where the pipe is to pierce the masonry chimney.

2.It will be necessary to break out the masonry around the location of the pipe center mark. Use a 4-inch diameter hole for 3-inch pipe and 5-inch diameter hole for 4-inch pipe.

3.Measure and build chimney top plate. Cut out holes for chimney pipe, and if used the outside air pipe.

4.Install the tee on the bottom of the vertical pipe system and lower it down the chimney until the center branch of the tee is level with the center of the hole in the masonry, as shown in Figure 10.

5.Install and seal the top plate from step 3 with non- hardening mastic. Slip the storm collar over the pipe, and while holding the pipe at the proper elevation, affix the collar with a minimum of three ¼” stainless steel sheet metal screws. Seal all joints and seams around the collar.

6.Connect the horizontal pipe by pushing it through the hole in the masonry and lining it up with the branch in the tee. Push the pipe into the tee while twisting it to lock it into the tee.

7.If desired, once the horizontal pipe is in place, the space between the pipe and masonry may be filled with high-temperature grout.

8.Install the trim collar. An adjustable pipe length and adapter may be needed to finish the connection to the stove.

FIGURE 9

FIGURE 10

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Vermont Important Information IntroductionSafety Precautions Table of Contents Specifications InstallationPreparation ClearancesWhen Outside AIR is not Used Combustion AIR SupplyVenting P4000 Installation Equivalent Vent Length EVLHorizontally Through Wall refer to Figure Vertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureVertically Into Existing Masonry Fireplace Installation Through Side of Masonry ChimneySpecial Mobile Home Requirements Electrical InstallationOperation PRE-START-UP Check Proper FuelBuilding a Fire Hotrod Automatic FirestarterShutdown Procedure Breckwell Maintenance ToolSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat Millivolt Thermostat is RequiredPlease Read this ASH Removal MaintenanceASH Disposal Vacuum USEBlowers CleaningDaily Weekly Annually or per Ton Chimney CleaningTroubleshooting Guide Stove Shuts OFF and the # 2 Light FlashesPossible Causes Stove Shuts OFF and the # 3 Light Flashes Possible Causes Possible Remedies Stove Feeds PELLETS, but will not IgniteSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide Heat Level Setting P4000 High Limit Switch Keeps TrippingSmoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Burnpot Replacement PartsLifetime Limited Warranty

P4000 specifications

The Breckwell P4000 is a pellet stove that combines efficiency, performance, and stylish design, making it an ideal choice for homeowners seeking an eco-friendly heating solution. With its robust construction and advanced technology, the P4000 stands out in a crowded market of heating appliances.

One of the key features of the Breckwell P4000 is its high heating capacity. Designed to heat spaces up to 2,200 square feet, it has a maximum output of 40,000 BTUs. This makes it suitable for both small and large rooms, providing a comfortable environment even in the coldest months. The stove also includes a large hopper capacity, able to hold up to 60 pounds of pellets, allowing for longer burn times without the need for constant refueling.

The P4000 is equipped with an advanced digital control panel. This user-friendly interface allows homeowners to easily adjust the thermostat and control the flame intensity, ensuring an optimal heating experience. Additionally, it features an automatic igniter for hassle-free start-up, allowing users to ignite their stove with the push of a button.

Efficiency and environmental performance are cornerstones of the Breckwell P4000's design. The stove boasts an impressive efficiency rating of up to 87%, meaning that minimal heat is lost during operation. This efficiency not only leads to lower heating bills but also reduces the environmental impact, as pellet stoves are considered a renewable energy source.

The P4000 also emphasizes safety, featuring a list of safety controls including a heat sensor and an automatic shut-off function. This ensures peace of mind for users, as it reduces the risk of overheating or fire hazards.

Another appealing aspect of the Breckwell P4000 is its aesthetic versatility. The stove comes in various finishes, including traditional black and modern stainless steel, allowing it to seamlessly integrate into various home decors. Its compact design ensures it can fit into tight spaces while still delivering powerful heating performance.

In conclusion, the Breckwell P4000 pellet stove combines modern technology, high efficiency, and attractive design. Its powerful heating capabilities, user-friendly controls, and safety features make it an excellent choice for homeowners looking for a reliable and stylish heating solution. Whether for a cozy living room or an expansive open space, the P4000 is dedicated to providing warmth and comfort during the cold months.
Top Page Image Contents