Breckwell P24I, P24FS owner manual Vertically with NEW Chimney System Refer to a & 9b

Page 8

8

INSTALLATION

B.VERTICALLY WITH NEW CHIMNEY SYSTEM (Refer to Figure 9a & 9b)

NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions.

OPTION: To achieve a center vertical installation a 45º elbow and a clean-out tee can be used to offset the pipe from the exhaust outlet to the rear center of the stove (see figure 9a). You can also use the P24FS Vertical Install Kit (part # A-VIK) (see figure 9b).

OPTION: Install L-Vent elbow in place of clean-out tee. Locate stove. Drop plumb bob to center of tee outlet, mark point on ceiling. Install ceiling support and L-Vent pipe per L-Vent manufacturer’s instructions.

1.Always maintain 3” clearance from combustible materials. When passing through additional floors or ceilings, always install firestop spacer.

2.After lining up for hole in roof, cut either around or square hole in roof, always 3” larger all the way around pipe. Install upper edge and sides of flashing under roofing materials, nail to the roof along upper edge. Do not nail lower edge. Seal nail heads with non-hardening waterproof mastic.

3.Apply non-hardening, waterproof mastic where the storm collar will meet the vent and flashing. Slide storm collar down until it sits on the flashing. Seal and install cap. Mobile home installations must use a spark arrester.

FIGURE 9a

FIGURE 9b

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Tradition Series P24 Introduction Important InformationSafety Precautions Table of Contents Installation SpecificationsPreparation ClearancesWhen Outside AIR is not Used Combustion AIR SupplyVenting Rear View P24FSA Rear View P24IHorizontally Through Wall refer to Figure Freestanding InstallationEquivalent Vent Length EVL Vertically with NEW Chimney System Refer to a & 9b Vertically Into Existing Chimney System Installation Through Side of Masonry Chimney Vertically Into Existing Masonry FireplaceInsert Installations Assembling the Flashing SETWhen Vent Pipe Extends to Chimney TOP AS a BUILT-IN Fireplace Special Mobile Home Requirements Electrical InstallationInstallation in to a Factory Built Metal Fireplace Operation Proper Fuel PRE-START-UP CheckBuilding a Fire Hotrod Automatic FirestarterBreckwell Maintenance Tool Shutdown ProcedureSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat Millivolt Thermostat is RequiredPlease Read this Maintenance ASH RemovalASH Disposal Freestanding Models ASH Disposal InsertCleaning Vacuum USEBlowers Rear View P24FSChimney Cleaning Recommended Maintenance ScheduleRemoval and Replacement of Broken Door Glass Daily Weekly Annually or per TonMaintenance Possible Causes Troubleshooting GuideStove Shuts OFF and the # 2 Light Flashes Stove Shuts OFF and the # 3 Light Flashes Stove Feeds PELLETS, but will not Ignite Possible Causes Possible RemediesSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide High Limit Switch Keeps Tripping Heat Level Setting P24Smoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Replacement Parts BurnpotLifetime Limited Warranty
Related manuals
Manual 32 pages 37.58 Kb Manual 9 pages 26.02 Kb

P24FS, P24I specifications

The Breckwell P24FS is a highly efficient pellet stove designed to provide both warmth and ambiance to your living space. Renowned for its dependable performance, this appliance combines cutting-edge technology with elegant design, making it a popular choice among homeowners seeking sustainable heating solutions.

One of the standout features of the P24FS is its impressive heating capacity. With the ability to effectively heat up to 2,000 square feet, the stove is equipped with a powerful 40,000 BTU output. This makes it suitable for various living spaces, from cozy cabins to larger family homes. Its large hopper capacity allows for extended burn times, which means less frequent refueling and more convenience for users.

The P24FS is engineered with advanced features such as an automatic ignition system, which simplifies startup and enhances efficiency. This stove also comes with a built-in thermostat, allowing users to maintain a consistent temperature effortlessly. The adjustable feed rate gives homeowners control over the amount of pellet fuel consumed, enhancing both efficiency and comfort.

Breckwell has incorporated a wide array of technologies into the P24FS to ensure optimal performance and safety. The stove features a substantial heat exchange system, which maximizes heat distribution throughout the room, while the integrated air wash system minimizes the buildup of soot on the glass door, ensuring a clear view of the mesmerizing flames.

Another notable characteristic of the P24FS is its aesthetic appeal. With a sleek and contemporary design, it complements a range of interior styles, from rustic to modern. The durable construction, combined with quality materials, ensures longevity and resilience.

In terms of EPA certifications, the Breckwell P24FS meets stringent emission standards, making it an environmentally friendly option for heating. Users appreciate the convenience of using fuel pellets, which are not only renewable but also offer a cleaner burn compared to traditional wood.

Overall, the Breckwell P24FS is a blend of efficiency, style, and user-friendliness. Its array of features, high heating capacity, and commitment to sustainability make it an excellent investment for those looking to enhance their home’s heating system with a reliable pellet stove. Whether it's for functional heating or creating a cozy atmosphere, the P24FS stands out as a top choice among its peers.
Top Page Image Contents