Avalon Stoves Arbor PS manual Start-Up Sequence, Manual Auger Button, Auger on Light, Fault Light

Page 25

Operation2 5

Start-Up Sequence

This stove utilizes a start-up sequence whenever the mode switch is changed or the heater is started when cold. This is to ensure proper operation through all possible settings and operational states (hot or cold, pellets burning or not burning, etc.). This sequence over-rides all user settings (except the "OFF" position) to set the auger feed rate to medium, the exhaust blower to high, and the igniter on. During this period the lowest “HEAT OUTPUT” light will flash.

"MANUAL AUGER" Button

This button turns the auger on. It is used to “prime” the auger after the hopper has run out of pellets.

"AUGER ON" Light

This light comes on when the auger is turning. This allows the operator to determine when the auger is turning.

"FAULT" Light

This light comes on when an error occurs:

•The stove runs out of pellets

•During initial start-up (for a split second) or for improper electrical frequency

•A start-up sequence that does not result in the heater coming up to temperature

To reset the fault light, turn the mode switch to off and re-start the stove.

DISCONNECT POWER BEFORE SERVICE

H

 

E

REMOTE

A

HIGH

T

AUTO

 

 

MANUAL

OMED

U

TAUGER

P LOW

U

FAULT

T

 

Fault Codes (for qualified service personnel only)

Fault and #2 (LOW) Light Flash = Flow Switch Fault

Fault and # 4 (MID) Light Flash = System Snap Disk Fault (pellets run out & stove goes cold)

Fault and # 6 (HIGH) Light Flash = Safety Snap Disk Fault

Power Outages

If a sustained power outage occurs while in "Manual", the stove will go to a "cool down" mode to vacate smoke once power returns. If the power outage was short, the heater will go to the start-up sequence. If in "Auto", the stove will re-start (if the room is cool).

!Because this stove relies upon a blower to evacuate the smoke, some smoke may enter the home during a power outage. To keep to a minimum, leave the door closed.

© Travis Industries

4070806

1 0 0 - 0 1 1 9 1 _ 0 0 0

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Arbor Introduction Important Information 2IntroductionTravis Industries 0 0 1 1 9 1 0 0Table of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Planning The Installation Installation OptionsStove Placement Before You BeginInstallation Clearances Straight InstallationClearances Corner Maximum Venting Distance Venting the Pellet StovePellet Vent Type Installing the Pellet VentPellet Vent Termination Outside Air used for combustion Mobile Home RequirementsBaffle Installation Alcove Installation RequirementsRestrictor Adjustment Door Seal VerificationRobertshaw Thermostat InstallationInstallation Example Direct Through-the-wall Installation Installation Example Interior Vertical Installation Installation Example Class a Chimney Retrofit Installation Example Masonry Fireplace Hearth Stove Vertical Cap Cover Plate non-combustible Storm Collar Vent Flex Section Installation Example Freestanding Masonry Chimney0Operation Safety NoticeLocation of Controls Starting the Heater for the First TimeLoading Pellets Operation2Two Modes of Operation To Adjust the Heat Manual Mode2Operation To StartTo Adjust Room Temperature or Start the Stove Auto Mode4Operation Adjusting the Fan SpeedPower Outages Fault LightStart-Up Sequence Manual Auger Button6Operation Using a Pellet/Corn Mix with This HeaterDaily Maintenance whenever using the stove Maintenance2Inspect the Burn Make Sure Pellets are Not Piling UpCleaning the Firepot 8MaintenanceCheck Firepot for Clinkers Door Opening Bi-Weekly Maintenance or every 10 bags of pellets 0MaintenanceClean the Hopper Clean the Heat Exchange TubesClean the Baffles Maintenance3Sweep Ash Into Ashpan 2MaintenanceCheck Ashpan, Dispose if necessary Clean the GlassYearly Maintenance or every two tons 4MaintenanceClean the Vertical Exhaust Duct Maintenance3 Clean the Exhaust Blower 6MaintenanceClean the Vent Clean the Convection BlowerAdjusting the Door Hinge and Latch Check for Air Leaks Around the Door, Glass, and AshpanDoor Replacement Parts Replacement PartsReplacement Parts Convection Fan Normal Operating SoundsSafety Label Years 1 & 2 Coverage Parts & Labor Limited 7 Year Warranty2Index

Arbor PS specifications

The Avalon Stoves Arbor PS stands out in the world of home heating solutions, combining advanced technology with exceptional design. This innovative wood stove is engineered to provide unmatched efficiency and style, making it a popular choice for homeowners looking to enhance both their comfort and aesthetic appeal.

One of the standout features of the Arbor PS is its powerful heating capacity. Designed to heat spaces of up to 2,000 square feet, it boasts impressive efficiency ratings that ensure optimal heat distribution, transforming cold living areas into warm, inviting spaces. Its ability to burn wood cleanly and efficiently means that homeowners can enjoy warmth without compromising air quality.

A key characteristic of the Arbor PS is its unique hybrid fuel technology. This technology allows for longer burn times and less frequent refueling, making it an incredibly convenient option. With a burn time of up to 12 hours, users can set their wood stove in the evening and wake up to residual warmth without the hassle of overnight maintenance.

The stove features an attractive, modern design, appealing to a wide range of decorating styles. Its sleek cast iron construction not only provides a rustic charm but also enhances durability, ensuring years of reliable performance. The large fire viewing window is another highlight, allowing users to appreciate the beauty of the flames while enjoying the heat it provides.

Safety is also a top priority with the Arbor PS. The stove is equipped with advanced safety features, including an airtight construction that minimizes the risk of air leaks and an adjustable air control for precise temperature regulation. Additionally, the stove’s high-efficiency design significantly reduces emissions, making it an eco-friendly option for environmentally conscious homeowners.

Installation is straightforward, thanks to the versatile flue outlet options which accommodate various setups. This flexibility, combined with the Arbor PS’s adaptability to both traditional and contemporary spaces, makes it a remarkable addition to any home.

In summary, the Avalon Stoves Arbor PS is a premier wood stove that excels in efficiency, aesthetics, and safety. It brings together cutting-edge technology and timeless design, making it an ideal choice for those seeking a reliable and stylish heating solution. With its combination of features, the Arbor PS is set to meet the demands of modern living while providing the comfort and charm that only a wood stove can offer.
Top Page Image Contents