Avalon Stoves Arbor PS Before You Begin, Packing List, Installation Options, Stove Placement

Page 7

Installation (For Qualified Installers Only)

7

Before You Begin

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE THIS HEATER. FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.

Check with local building officials for any permits required for installation of this pellet heater and notify your insurance company before proceeding with installation.

Packing List

• Thermostat & Wire

• Scraper Rod Tool • Brush • Spare Fuse • Bottle Brush • Door Tool

• (2) Floor Mounting Brackets

Installation Options

Residential or Mobile Home (see the section "Mobile Home Requirements")

Alcove Compatible (see the section "Alcove Installation")

Horizontal or Vertical Vent

Outside Air Compatible

Vent with L-Vent, L-Vent Fireplace Liner, or Type A Chimney (with adapter)

Planning The Installation

HINT:

Have an authorized Travis Industries dealer install this heater. If you install the heater

 

yourself, have your dealer review your installation plans.

HINT:

Sketch out a detailed plan of the installation including dimensions. Then verify the

 

dimensions with the requirements listed in this manual.

HINT:

When determining the location of the stove, locate the wall studs (for horizontal

 

penetrations) and ceiling trusses (for vertical penetrations). You may wish to adjust the

 

stove position slightly to ensure the vent does not intersect with a framing member.

HINT:

Place the heater outside and load 10 pounds of pellets inside the hopper. Plug the

 

heater in and let it run on HIGH until the pellets run out. This will cure the paint and burn

 

off any oil on the steel, eliminating any smell inside the home.

Stove Placement

Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" of the front of the heater.

If the stove is placed in a location where the ceiling height is less than 7', it must follow the requirements in the section "Alcove Installation Requirements".

HINT:

REDUCING CLEARANCES - Clearances may be reduced by methods specified in NFPA

 

211, listed wall shields, pipe shields, or other means approved by local building or fire

 

officials.

Heater and floor protection must be installed on a level, secure floor.

Floor Protection Requirements

The heater must be installed on a non-combustible floor protector extending the full width and depth of the heater and extending 6" in front (minimum 27-3/4" wide by 31" deep) (minimum .018" thick - 26 gauge) .

Must extend under and 2" to each side and rear of a "Tee" (if used).

© Travis Industries

4070806

1 0 0 - 0 1 1 9 1 _ 0 0 0

Image 7
Contents Arbor 0 0 1 1 9 1 0 0 2IntroductionIntroduction Important Information Travis IndustriesTable of Contents 4Safety Precautions Mobile Home Safety Precautions6Specifications Before You Begin Installation OptionsPlanning The Installation Stove PlacementInstallation Clearances Straight InstallationClearances Corner Maximum Venting Distance Venting the Pellet StovePellet Vent Type Installing the Pellet VentPellet Vent Termination Outside Air used for combustion Mobile Home RequirementsDoor Seal Verification Alcove Installation RequirementsBaffle Installation Restrictor AdjustmentRobertshaw Thermostat InstallationInstallation Example Direct Through-the-wall Installation Installation Example Interior Vertical Installation Installation Example Class a Chimney Retrofit Installation Example Masonry Fireplace Hearth Stove Vertical Cap Cover Plate non-combustible Storm Collar Vent Flex Section Installation Example Freestanding Masonry ChimneyStarting the Heater for the First Time Safety Notice0Operation Location of ControlsLoading Pellets Operation2Two Modes of Operation To Start Manual ModeTo Adjust the Heat 2OperationTo Adjust Room Temperature or Start the Stove Auto Mode4Operation Adjusting the Fan SpeedManual Auger Button Fault LightPower Outages Start-Up Sequence6Operation Using a Pellet/Corn Mix with This HeaterMake Sure Pellets are Not Piling Up Maintenance2Daily Maintenance whenever using the stove Inspect the BurnCleaning the Firepot 8MaintenanceCheck Firepot for Clinkers Door Opening Clean the Heat Exchange Tubes 0MaintenanceBi-Weekly Maintenance or every 10 bags of pellets Clean the HopperClean the Baffles Maintenance3Sweep Ash Into Ashpan 2MaintenanceCheck Ashpan, Dispose if necessary Clean the GlassYearly Maintenance or every two tons 4MaintenanceClean the Vertical Exhaust Duct Maintenance3 Clean the Exhaust Blower 6MaintenanceCheck for Air Leaks Around the Door, Glass, and Ashpan Clean the Convection BlowerClean the Vent Adjusting the Door Hinge and LatchDoor Replacement Parts Replacement PartsReplacement Parts Convection Fan Normal Operating SoundsSafety Label Years 1 & 2 Coverage Parts & Labor Limited 7 Year Warranty2Index

Arbor PS specifications

The Avalon Stoves Arbor PS stands out in the world of home heating solutions, combining advanced technology with exceptional design. This innovative wood stove is engineered to provide unmatched efficiency and style, making it a popular choice for homeowners looking to enhance both their comfort and aesthetic appeal.

One of the standout features of the Arbor PS is its powerful heating capacity. Designed to heat spaces of up to 2,000 square feet, it boasts impressive efficiency ratings that ensure optimal heat distribution, transforming cold living areas into warm, inviting spaces. Its ability to burn wood cleanly and efficiently means that homeowners can enjoy warmth without compromising air quality.

A key characteristic of the Arbor PS is its unique hybrid fuel technology. This technology allows for longer burn times and less frequent refueling, making it an incredibly convenient option. With a burn time of up to 12 hours, users can set their wood stove in the evening and wake up to residual warmth without the hassle of overnight maintenance.

The stove features an attractive, modern design, appealing to a wide range of decorating styles. Its sleek cast iron construction not only provides a rustic charm but also enhances durability, ensuring years of reliable performance. The large fire viewing window is another highlight, allowing users to appreciate the beauty of the flames while enjoying the heat it provides.

Safety is also a top priority with the Arbor PS. The stove is equipped with advanced safety features, including an airtight construction that minimizes the risk of air leaks and an adjustable air control for precise temperature regulation. Additionally, the stove’s high-efficiency design significantly reduces emissions, making it an eco-friendly option for environmentally conscious homeowners.

Installation is straightforward, thanks to the versatile flue outlet options which accommodate various setups. This flexibility, combined with the Arbor PS’s adaptability to both traditional and contemporary spaces, makes it a remarkable addition to any home.

In summary, the Avalon Stoves Arbor PS is a premier wood stove that excels in efficiency, aesthetics, and safety. It brings together cutting-edge technology and timeless design, making it an ideal choice for those seeking a reliable and stylish heating solution. With its combination of features, the Arbor PS is set to meet the demands of modern living while providing the comfort and charm that only a wood stove can offer.