CFM UVC36, UVC43, UVS43 Electrical Connection, Hard DIrect Wire Hook-Up, EB1 Receptacle Hook-Up

Page 8

Majestic Fireplaces® UVC / UVS Vent-Free Heaters

Always check for gas leaks with a mild soap and water solution. Do not use an open

flame for leak testing.

The gas control is equipped with a captured screw type pressure test point, therefore it is not necessary to pro- vide a 1/8" test point up stream of the control.

When using copper or flex connector use only approved fittings. Always provide a union so the gas line can be easily disconnected for burner or fan servicing.

See gas specification for pressure details and ratings. NOTE: If flex connector is used, it must be kept inside of the heater. (Fig. 7)

1/2" Gas Supply

1/2" x 3/8" Shut Off Valve

3/8" Nipple

3/8" Union

3/8"

Nipple

FP297

Fig. 7 Typical gas supply installation.

Electrical Connection

When installed, the heater must be electri- cally connected and grounded in accor- dance with local codes or, in the absence of local codes:

U.S. Installations: Follow local codes and the National Electrical Code, ANSI/NFPA No. 70.

NOTE: 110/120 electric power is required to operate blower (fan).

Be sure to leave sufficient excess wire in case minor adjustments are required.

Any electrical re-wiring of this fan must be done by a qualified electrician.

Whether wiring directly to the fan junction box or into the EB1 (electrical receptacle box, P/N ZA1200) first ensure cable is secured using box connector.

Turn off all power before hook-up.

Hard (DIrect) Wire Hook-Up:

First connect ground wire to ground stud located on the base of either box. Black wire from supply should connect to the variable speed switch. Alternate speed switch wire connects to temperature sensor. Alternate lead from sensor connects to fan. Alternate fan con-

nects back to white supply wire. (Fig. 8)

 

Fan

 

Temperature

 

Sensor

Speed

Control

Black

 

White

 

Ground

 

FP394

Fig. 8

Wiring diagram.

EB1 (Receptacle) Hook-Up

1.Remove 2" knockout. Slide the electrical box back plate into the back and bottom lances (clips) while fit- ting the box connector into the knockout. Fasten into place with fastening screws provided. (Fig. 9)

2.Connect the black positive wire to brass screw (polarized side) of the receptacle. The white wire is connected to the chrome screw. The ground wire is connected to the green ground screw of the recep- tacle. Fit the receptacle into the electrical box.

3.Screw the cover plate provided to the electrical box.

INSIDE

Electrical Box

 

 

Fastening Screws

 

Gas Inlet Hole

FRONTOFUNIT

OUTSIDE

Gas Inlet Hole

 

OF

UNIT

FRONT

 

 

FP298

 

 

Fig. 8 Junction box (EB-1) hook-up.

Remote Wall Switch

CAUTION: Do not wire millivolt remote wall switch for gas heater to a 120v power sup- ply. For lighting instructions, see Page 12.

1.Thread wire through the electrical knockout located on either side of unit. Do not cut wire or insu- lation on metal edges. Ensure that wire is protected. Run the other end to a conveniently located wall

receptacle box.

8

20000135

Page 7 Page 9
Image 8
Page 7 Page 9
Contents UVC43 Table Of Contents Installation & Operating Instructions This appliance is intended for supplemental heatingUVC/UVS36 Vent Free Room Heater Safety Devices DescriptionClearance to Combustibles ApplianceMantels Hearth ExtensionPlanning Mounting the HeaterGas Specifications Gas Inlet and Manifold PressuresHigh Elevations Gas Supply PressuresHard DIrect Wire Hook-Up Remote Wall SwitchElectrical Connection EB1 Receptacle Hook-UpAlternate Switch Location Slide the Heater in PlaceLevel and Secure the Heater FinishingLog Installation Window Frame Assembly Removal Glass CleaningOperating Instructions Glass InformationEmber Material Placement Flame AdjustmentFlame Characteristics Lava RockLighting And Operating Instructions To Turn Off Gas To HeaterTroubleshooting Nova SITMaintenance Cleaning the Standing Pilot Control SystemCleaning Catalytic Filters UVC Only Burner and Burner CompartmentUVC/UVS 36/43 Vent Free Heaters DescriptionUVC/UVS 36/43 Vent Free Heaters Optional Accessories Remote ControlsFan Kit Ceramic Refractory PanelsDecorative Frame Trims Decorative Bay WindowEB-1 Electrical Box Outside Air TerminationLimited Lifetime Warranty CFM Specialty Home Products

UVC43, UVC36, UVS36, UVS43 specifications

CFM International has made significant advancements in the field of avionics with its cutting-edge line of aircraft engines, including the CFM UVS43, UVS36, UVC36, and UVC43 models. These engines are designed to enhance performance, reliability, and efficiency, catering to a broad spectrum of aviation needs.

The CFM UVS43 is engineered for high-performance applications, offering exceptional thrust and fuel efficiency. Its advanced materials and aerodynamic design allow for reduced weight and increased durability. The UVS43 employs state-of-the-art technologies, including a full-authority digital engine control (FADEC) system which optimizes engine performance by intelligently adjusting parameters in real-time.

Similarly, the UVS36 model is known for its versatility and adaptability in various aviation platforms. The engine incorporates a unique dual-spool design that provides improved efficiency at different altitudes and speeds. The UVS36 is equipped with advanced noise reduction technologies, ensuring compliance with stringent environmental regulations without compromising on performance.

The CFM UVC36 is another standout in the CFM engine lineup, designed specifically for regional aircraft. It features a compact design that allows for easy integration into smaller airframes while providing reliable thrust and performance. The UVC36 employs innovative cooling technologies that enhance engine longevity and reduce maintenance intervals, making it an attractive option for operators concerned with operational costs.

On the other hand, the UVC43 is tailored for larger aircraft, offering increased power output and efficiency. This model utilizes advanced composite materials, allowing for a lighter engine that still delivers exceptional performance. The UVC43 is also notable for its improved fuel consumption rates compared to previous models, thanks to its advanced turbine and combustion chamber design.

All four engine models share a commitment to sustainability, featuring reduced emissions and noise levels while enhancing operational efficiency. The integration of cutting-edge computer modeling and simulation techniques during the design phase has contributed to optimized performance across all models. With their combination of innovation, flexibility, and reliability, the CFM UVS43, UVS36, UVC36, and UVC43 engines represent the future of aviation powerplants, meeting the demanding requirements of modern air transport while ensuring a reduced environmental footprint. As aviation continues to evolve, CFM remains at the forefront, driving advancements that shape the industry.
Top Page Image Contents