Billy Goat VQ1002SP, VQ802SPH specifications Maintenance Schedule

Page 15
1717. 2.1

17MAINTENANCE continued

CHAIN ADJUSTMENTS (see figure 9)

1.Remove guards.

2.Inspect chain and sprockets for wear, lubrication and tension. Replace if badly worn or damaged. CHAIN TENSION AND ALIGNMENT (see figure 9)

3.Install new chain, locating keeper clip of chain connecting link on inboard side of chain.

4.Reinstall bearings onto axle and assemble bearing mounting screws. Leave screws only partially tightened.

5.Push bearings outward against each rear wheel, fully spreading wheels to both ends of axle.

6.With bearings pressed fully outward against wheels, keeping axle square with engine base, align and tension chain as shown below and slightly tighten front bearing screws first. Then slightly tighten rear bearings. (Note: Tightening front bearing screws first, helps keep chain tight.)

7.Recheck chain alignment, tension and axle squareness. If ok, fully tighten front and then rear bearing screws. Repeat adjust- ment steps if necessary.

8.Check chain tension and roll wheels to be sure there are no excessively tight areas in the chain. Readjust if necessary. A slightly loose chain is better than an over tightened one.

9. Reinstall chain guard and differential guard.

10. Reinstall spark plug wire.

Maintenance Schedule

Follow these hourly maintenance intervals.

More frequent service is required for extremely dusty conditions.

Maintenance Operation

Every

Every 5 hrs

Every 25

Every 50

Use

or (Daily)

hours

hours

 

Engine (See Engine

Manual)

Check for excessive vibration

Clean Debris Bag

Check bag strap tightness

Inspect for loose parts

Inspect for damaged parts

Check tire pressure (p. 15)

Oil control pivot points

Lubricate Drive Chain

Check belt adjustment (p.15)

Grease wheel zerks

Belt Adjustment: As V-belt wears, adjustments may be required. Adjust by tightening or by loosening clutch cable nut as required. When replacing the belt, the impeller must be removed. See instructions on page 14. See parts list for impeller bolt torque specifications. See figure 10 & 11 for proper belt tension adjustment. If cable cannot be adjusted to provide proper belt tension then belt must be replaced. DO NOT OVER ADJUST.

Chain Lubrication: With machine not running, oil chain using general S.A.E. 30 weight oil every 25 hours or as

needed. Chain oiling hole is located in rear axle cover. Note: Be sure that entire length of chain is properly oiled. Oiling only a few positions in the chain rotation will not properly oil the chain.

 

 

 

 

 

0.06 (1.5mm)

 

 

 

 

 

 

 

0.125 (3.3mm)

PULLEY

TRANSMISSION

IDLER PULLEY BELT

WIRE

 

IDLER PULLEY

PULLEY

IN DRIVE

BELT

 

IN NEUTRAL

TURNS

 

 

 

 

POSITION

GUIDES

 

POSITION

FREELY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.06 (1.5mm)

 

 

 

0.125 (3.3mm)

 

ENGAGED DRIVE POSITON: WIRE BELT

 

NEUTRAL POSITION

GUIDES SHOULD CLEAR BELT BY 0.06" - 0.125"

 

 

(1.5mm - 3.3mm)

Fig. 10

 

Fig. 11

 

 

 

 

 

Part No. 830542

 

Page 15 of 16

Form No. F021302G

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Ride on Chariot KIT VQ802SPH, VQ1002SPVacuum Hose KIT Hose Coupler KITTable of Contents Sound VibrationStarting Position ThrottleControl StopCheck Debris Bag 830170A Boxing ChecklistElbow Assembly Check Deflector Assembly138 118 Deflector NotchPUT OIL in Engine Before Starting Self Propelled only before starting unitVacuuming Operation Vacuum Nozzle Height Adjustment IsClearing a Clogged Nozzle Debris BAGDrive Gear Selection @ 3400 RPM PropulsionFor reverse Set Throttle to Idle Throttle ControlVQ802SPH, VQ1002SP Parts DrawingForm No. F021302G Description VQ802SPH QTY Brkt Transmission WA VQ Label Speed Control CUT to Make Switch & Wire Assembly Parts ListStorage Handling & TransportingEngine Disconnect Spark Plug Wire Before Servicing UnitMaintenance Debris BAG SeeMaintenance Schedule MaintenanceSerial Plate TroubleshootingEngine Service and Warranty Warranty Procedure

VQ1002SP, VQ802SPH specifications

The Billy Goat VQ1002SP and VQ802SPH are innovative and powerful solutions in the world of outdoor clean-up and landscaping equipment. Designed primarily for commercial and residential use, these vacuum systems are engineered to handle a variety of debris, ensuring that users can maintain a clean and pristine environment effortlessly.

The VQ1002SP model is powered by a robust 10.0 HP engine, delivering exceptional suction performance. This machine is perfect for larger properties and jobs where heavy-duty clean-up is necessary. Its unique design features a large intake opening, allowing it to collect leaves, grass, and even small debris with ease. Equipped with a 39-gallon debris bag, the VQ1002SP minimizes the frequency of emptying, enabling users to work more efficiently and effectively.

On the other hand, the VQ802SPH model offers slightly smaller dimensions but is packed with powerful capabilities. With an 8.0 HP engine, this model strikes a balance between power and portability. The VQ802SPH is particularly user-friendly, making it an excellent choice for homeowners or professional landscapers who need a more compact solution without sacrificing performance. Its lightweight design and versatile features enhance maneuverability, allowing operators to navigate tight spaces with confidence.

Both models incorporate advanced vacuum technology, including an innovative impeller system that maximizes air volume while minimizing clogs. This ensures consistent performance and reliability even when challenged with dense debris. Furthermore, the use of durable, high-quality materials means that both vacuum systems are built to withstand rigorous use in various weather conditions.

Safety and convenience have been prioritized in the design of the VQ1002SP and VQ802SPH, featuring ergonomic handles for comfortable operation and dependable controls for ease of use. Additionally, both models come with quick-release bag systems, simplifying the process of disposing of collected debris.

In conclusion, the Billy Goat VQ1002SP and VQ802SPH vacuum systems standout in the landscaping equipment market due to their powerful engines, advanced suction technology, and user-friendly design. Whether managing a large commercial property or tending to a modest garden, these vacuum systems provide reliable performance, durability, and versatility to meet a wide range of needs.
Top Page Image Contents