Billy Goat VQ802SPH Vacuum Nozzle Height Adjustment Is, Clearing a Clogged Nozzle, Debris BAG

16 OPERATION

INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter. Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.

Self propelled unit is not intended for use with any ground engaging implements [maximum tow bar weight 300 lbs (136 kg)].

Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects.

Note: See parts list for proper impeller bolt torque specifica- tions. (See trouble shooting section on page 16).

Like all mechanical tools, reasonable care must be used when operating machine.

Inspect machine work area and machine before operat- ing. Make sure that all operators of this equipment are trained in general machine use and safety.

FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle.

NOTE: Never bury nozzle into debris.

CLEARING A CLOGGED NOZZLE

& EXHAUST: Turn engine off and wait for impeller to stop completely and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire.

NOZZLE GOBBLER DOOR.

Large debris can be vacuumed without readjusting nozzle height by temporarily opening the remote Nozzle Gobbler Door. For maxi- mum pickup of small debris, the gobbler door must be down, flush with front face of nozzle.

	PUT OIL IN ENGINE BEFORE STARTING.		16.3 DEBRIS BAG
			Debris bags are normal replaceable wear items.
16.1	STARTING		Note: Frequently empty debris to prevent bag overloading with
	ENGINE: See engine manufacturer’s instructions		more weight than you can lift.
			An optional bag and dust cover is available for use where debris will be
	for type and amount of oil and gasoline used.
			vacuumed in dusty conditions (See Optional Accessories shown on
Engine must be level when checking and filling oil and			page 1.)
gasoline.			DO NOT place bag on or near hot surface, such as engine. Run
ENGINE SPEED: Controlled by throttle lever on left side of			engine at 1/2 throttle for first 1/2 hour to condition new bag. Your
handle. Under normal conditions operate at minimum throttle			new bag requires a break-in period to condition the pores of the
to accomplish your current cleaning task. For Honda model,			material against premature blockage. The entire bag surface
the stop switch is located on the switch panel on the engine			serves as a filter, and must be able to breath to have good vacuum
& for SP Honda models only, on remote shift control panel.			performance.
			Be sure engine has come to a complete stop before removing
NOTE: Before starting, check that all switches and fuel
			or emptying bag.
valves are on.
			This vacuum is designed for picking up trash, organic
FUEL VALVE: Move fuel shutoff valve to "ON" position.
			material and other similar debris (see Safety Warnings page 2-4).
CHOKE: Located at lower rear area of carburetor bowl.			However, many vacuums are used where dust is mixed with
Choke engine before starting when engine is cold.			trash. Your unit can intermittently vacuum in dusty areas. Dust
THROTTLE: Move remote throttle control to fast position.			is the greatest cause of lost vacuum performance. However,
			following these rules will help maintain your machine's ability to
Pull starting rope to start engine.
			vacuum in dusty conditions:
IF YOUR UNIT FAILS TO START:
			•Run machine at idle to quarter throttle.
See Troubleshooting on page 16.
			•The debris bag must be cleaned more frequently. A vacuum
			with a clean, pillow soft bag will have good pickup performance.
16.2	VACUUMING OPERATION		One with a dirty, tight bag will have poor pickup performance. If
			dirty, empty debris and vigorously shake bag free of dust.
VACUUM NOZZLE HEIGHT ADJUSTMENT: Is			•Machine or pressure-wash debris bag if normal cleaning does
adjusted by unlocking wing nut (item 32) and turning caster			not fully clean bag. Bag should be thoroughly dry before use.
knob. Turning the knob clockwise increases height. Be sure			Having one or more spare debris bags is a good way to reduce down time
the nozzle height is level (left to right) before tightening caster
			while dirty bags are being cleaned.
wing nuts.
			•DO NOT leave debris in bag while in storage.
Adjust nozzle height according to surface conditions and
debris size; For vacuuming on flat surfaces, set nozzle 1/2"
(12.7 mm) to 5/8" (15.8 mm) above ground; Higher for uneven
terrain and turf. Note: The nozzle side bogie wheels should
be at least 1/8" (3.2mm) above the ground, or maneuver-
ability will be reduced.
Part No. 830542		Page 6 of 16		Form No. F021302G