Billy Goat VQ1002SP, VQ802SPH Deflector Notch, PUT OIL in Engine Before Starting, 138 118

Page 5

10ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING.

Your Billy Goat is shipped from the factory in one carton, com- pletely assembled except for the debris bag, deflector assy, upper handle assembly, rod nozzle door, elbow assy.

1. UPPER HANDLE (item 41). Assemble securely to lower handle stubs (item 37) and handle brace (item 36), using screws (item 120 & 121), so that screw heads are on inside of handle. Other- wise, premature bag wear could result.

2. NOZZLE DOOR CONTROLS. Assemble ball joints (item 73), jam nuts (item 138), to both ends of rod (item 47). Do not fully tighten jam nuts.

Using screw (item 113), washer (item 143) and lock nut (item 131), connect one end of rod (item 47) to nozzle door mounting. (See Figure 5). Using rod, pull nozzle door open horizontal to ground and hold opposite end of rod next to mounting hole on remote lever (item 48), already assembled onto upper handle. (See Figure 1). If necessary, adjust rod length using threads provided on rod. Adjust rod length to give a minimum of 1.0" (25.4 mm) hand clearance between lever & maximum forward throttle position when door is open. Assemble upper end of rod to lever on handle using same hardware item numbers as shown above. (See figure 1& 2). Tighten jam nuts.

3. EXHAUST ASSY. Place flange gasket (item 35) onto housing of main unit and assemble exhaust elbow to housing using screws (item 117), washers (item 140) and lock nuts (item 132), provided in parts bag. The rear hole mounts deflector (item 118), using screw assembly (already attached to deflector) and lock nut (item 132). Bend opposite end of deflector down until notch in rear of deflector catches onto handle brace (item 36) (see figure 3).

4. DEBRIS BAG (Item 50) (see figure 4).

4.1Unfold and place mouth of bag over exhaust elbow, com- pletely covering the discharge opening with bag neck straps, placing one on each side of elbow flange.

COMPLETELY TIGHTEN BAG NECK STRAPS

4.2Attach rear hanger straps of bag to the hanger loops

located one on each side of the upper handle.

5. CABLES AND WIRES. Attach to the handle using cable clamps (item 44).

6.Secure engine starter rope into starter rope guide (Item 177) using hardware that is preassembled to the lower handle.

7.INSPECT ALL PARTS & MECHANICAL FASTENERS for security and integrity.

8.Note: See debris bag conditioning under operation section on page 6).

SELF PROPELLED ONLY (before starting unit).

9. CONTROL ASSY (item 77).

Before starting engine, check for neutral N by

placing the control into neutral and engaging the bail, the unit has been adjusted at the factory and should free- wheel. If not, adjust as needed by placing the control (item 77) and transmission offset link (item 68) into neutral and adjust nuts on control cable(item 75).

10.Check tire pressure and lubricate all grease and oil points (see 17 MAINTENANCE).

11.Connect spark plug wire.

48

73

138

47

47

138

73

118

Deflector

Notch

36

50

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 6

Part No. 830542

Page 5 of 16

Form No. F021302G

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Vacuum Hose KIT VQ802SPH, VQ1002SPHose Coupler KIT Ride on Chariot KITStarting Table of ContentsSound Vibration Control ThrottleStop PositionElbow Assembly Boxing ChecklistCheck Deflector Assembly Check Debris Bag 830170APUT OIL in Engine Before Starting Deflector NotchSelf Propelled only before starting unit 138 118Clearing a Clogged Nozzle Vacuum Nozzle Height Adjustment IsDebris BAG Vacuuming OperationFor reverse Set Throttle to Idle PropulsionThrottle Control Drive Gear Selection @ 3400 RPMVQ802SPH, VQ1002SP Parts DrawingForm No. F021302G Description VQ802SPH QTY Brkt Transmission WA VQ Label Speed Control CUT to Make Switch & Wire Assembly Parts ListStorage Handling & TransportingMaintenance Disconnect Spark Plug Wire Before Servicing UnitDebris BAG See EngineMaintenance Schedule MaintenanceEngine Service and Warranty TroubleshootingWarranty Procedure Serial Plate

VQ1002SP, VQ802SPH specifications

The Billy Goat VQ1002SP and VQ802SPH are innovative and powerful solutions in the world of outdoor clean-up and landscaping equipment. Designed primarily for commercial and residential use, these vacuum systems are engineered to handle a variety of debris, ensuring that users can maintain a clean and pristine environment effortlessly.

The VQ1002SP model is powered by a robust 10.0 HP engine, delivering exceptional suction performance. This machine is perfect for larger properties and jobs where heavy-duty clean-up is necessary. Its unique design features a large intake opening, allowing it to collect leaves, grass, and even small debris with ease. Equipped with a 39-gallon debris bag, the VQ1002SP minimizes the frequency of emptying, enabling users to work more efficiently and effectively.

On the other hand, the VQ802SPH model offers slightly smaller dimensions but is packed with powerful capabilities. With an 8.0 HP engine, this model strikes a balance between power and portability. The VQ802SPH is particularly user-friendly, making it an excellent choice for homeowners or professional landscapers who need a more compact solution without sacrificing performance. Its lightweight design and versatile features enhance maneuverability, allowing operators to navigate tight spaces with confidence.

Both models incorporate advanced vacuum technology, including an innovative impeller system that maximizes air volume while minimizing clogs. This ensures consistent performance and reliability even when challenged with dense debris. Furthermore, the use of durable, high-quality materials means that both vacuum systems are built to withstand rigorous use in various weather conditions.

Safety and convenience have been prioritized in the design of the VQ1002SP and VQ802SPH, featuring ergonomic handles for comfortable operation and dependable controls for ease of use. Additionally, both models come with quick-release bag systems, simplifying the process of disposing of collected debris.

In conclusion, the Billy Goat VQ1002SP and VQ802SPH vacuum systems standout in the landscaping equipment market due to their powerful engines, advanced suction technology, and user-friendly design. Whether managing a large commercial property or tending to a modest garden, these vacuum systems provide reliable performance, durability, and versatility to meet a wide range of needs.
Top Page Image Contents