Rheem Commercial Power Direct Vent Water heater For Your Safety Read Before Operating

Page 15
THERMOST AT

Operation

Before operating this water heater, be sure to read and follow the instructions on the label pictured below and all other labels on the water heater, as well as the warnings printed in this manual. Failure to do so can result in unsafe operation of the water heater resulting in prop- erty damage, bodily injury, or death. Should you have any problems reading or following the instructions in this manual, STOP, and get help from a qualified person.

1. LIGHTING PROCEDURE - Lighting procedures are outlined on the label pictured below. This label is also located on the water heater near the thermostat.

NOTICE: The Gas Valve supplied with this water heater may vary from the one pictured on the label below, but the Lighting Instructions are the same for all types of valves supplied with this model water heater.

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructionsexactly, a fire or explosion may result causing propertydamage, personal injury or loss of life.

A.This appliance is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot by hand.

B.BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your handto turnthe gas controlknob. Never use tools. If the knobwill not turnby hand, don'ttry to repair it, call a qualified service technician. Force or attemptedrepair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified ser - vice technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

OPERATING INSTRUCTIONS

1.STOP! READ THE SAFETY INFORMATION ABOVE ON THIS LABEL.

2.REMOVE OUTER COVER. USING A SLOTTED SCREWDRIVER - INSERT INTO SLOT IN CENTER OF DIAL. TURN DIAL COUNTERCLOCKWISE

TO THE LOWEST SETTING .

Honeywell

5.TURN THE "GAS CONTROL KNOB" CLOCK- WISE TO " OFF".

6.WAIT FIVE (5) MINUTES TO CLEAR OUT ANY GAS. IF YOU THEN SMELL GAS, STOP! FOL- LOW "B" IN THE SAFETY INFORMATION ABOVE ON THIS LABEL. IF YOU DON'T SMEL L GAS, GO TO NEXT STEP.

TEMPERATURE

Index ADJUSTMENT

DIAL

Ga s C ock

 

 

NOTE: Thermostat

GAS

VA LV E

shown with cover

Knob

removed .

 

 

3.TURN OFF ALL ELECTRIC POWER TO TH E APPLIANCE.

7.TURN THE "GAS CONTROL KNOB" COUNTER- CLOCKWISE TO "ON".

8.TURN ON ALL ELECTRIC POWER TO THE APPLIANCE.

9.SET THERMOSTAT TO D ESIRED SETTING. INSTAL L OUTER COVER.

4. THIS APPLIANCE

IS EQUIPPED WITH AN 10.

IF THE APPLIANCE WILL NOT OPERATE, FOL-

IGNITION DEVICE

WHICH AUTOMATICALLY

LOW THE INSTRUCTIONS "TO TURN OFF GAS

LIGHTS THE PILOT. DO NOT TRY TO LIGHT THE

TO APPLIANCE" AND CALL YOUR SERVICE

PILOT BY HAND.

 

TECHNICIAN OR GAS SUPPLIER.

TO TURN OFF GAS TO APPLIANCE

1.

TURN OFF ALL ELECTRIC POWER TO THE

3. TURN THE "GAS CONTROL KNOB" CLOCK-

 

APPLIANCE IF SERVICE IS TO BE PERFORMED.

WISE TO "OFF" .

2.

SET THE THERMOSTA T TO LOWEST SETTING.

 

15

Image 15
Contents USE & Care Manual Read the Safety Information N G E R General Safety PrecautionsSity can also hide or camouflage a gas leak N G E RIntroduction Local Installation RegulationsInstallation Typical Installation Drawing Venting Minimum and Maximum Vent Lengths Building Additional Considerations See FigureHorizontal Vent Terminal Location Cleaner-Primer and Medium Body Solvent Cement For Proper Installation Installation Check ListOperation ForyoursafetyreadbeforeoperatingFor Your Safety Read Before Operating HoneywellWhite-Rodgers Safety PrecautionsEmergency Shutdown MaintenanceVERIFY PROPER OPERATION AFTER SERVICING Power System Sentinel Diagnostic SystemPOWER LED System SentinelTroubleshooting GuideTHERMOSTAT LED IGNITION LED PILOT VALVE LED MAIN VALVE LED ECO LEDInstructions For Placing a Parts Order Replacement Parts120V Wiring and Schematic DiagramsFY PROPER OPERATION AFTER SERVICING How to Obtain Service Assistance

Commercial Power Direct Vent Water heater specifications

The Rheem Commercial Power Direct Vent Water Heater is engineered to meet the demanding needs of commercial applications, providing reliable and efficient hot water for various business environments. With a focus on performance, efficiency, and durability, this water heater stands out in the competitive landscape of commercial water heating solutions.

One of the key features of the Rheem Commercial Power Direct Vent Water Heater is its direct vent capability. This innovative design allows for installation in confined spaces while optimizing exhaust methods. The direct vent system enables the heater to draw air from outside the building for combustion, ensuring safe operation, reducing risk of backdraft, and maintaining indoor air quality.

The water heater is powered by either natural gas or propane, accommodating diverse fuel supply preferences. With a range of storage capacities, it can cater to small and large businesses, from restaurants to industrial facilities. The product’s high recovery rate ensures that it can meet peak hot water demands, making it an ideal solution for facilities with fluctuating hot water usage.

Equipped with advanced technology, the Rheem Commercial Power Direct Vent Water Heater features a state-of-the-art electronic control system that allows for easy temperature adjustments and monitoring. This interface ensures precise temperature control, so businesses can consistently deliver hot water at the required temperatures.

Durability is a hallmark of this water heater, which incorporates premium-grade components and materials. The tank is constructed with a glass-lined steel design that enhances resistance to corrosion, while also supporting longevity. Additionally, it features robust insulation that reduces heat loss, improving energy efficiency and lowering operating costs.

Another notable characteristic is the inclusion of a high-efficiency burner that maximizes fuel utilization, promoting energy savings and reducing emissions. The heater also complies with various energy standards, making it a sustainable choice for environmentally conscious businesses.

Installation and maintenance are streamlined with the Rheem Commercial Power Direct Vent Water Heater. Its compact design and versatile venting options allow for flexible placement. Furthermore, the unit is designed for easier access to critical components, making routine service and maintenance uncomplicated.

Overall, the Rheem Commercial Power Direct Vent Water Heater represents a fusion of efficiency, ease of use, and advanced technology, making it a smart investment for commercial establishments needing reliable hot water solutions. Whether in kitchens, manufacturing plants, or commercial offices, this water heater is engineered to deliver performance and peace of mind.