Desa A, C, B To Turn OFF GAS to Appliance, Thermostat Control Operation, Shutting Off Heater

Page 17

OPERATING HEATER (THERMOSTAT-CONTROLLED MODELS)

To Turn Gas Off To Appliance

Thermostat Control Operation

Manual Lighting Procedure

OPERATING HEATER (MANUALLY-CONTROLLED MODELS)

For Your Safety Read Before Lighting

Lighting Instructions

17

OPERATING HEATER

Continued

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise to the OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise to the PILOT position.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to any comfort level between HI and LO. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

Note: Selecting the HI setting with the control knob will cause the burner to remain fully on, without modulating down in most cases.

MANUAL LIGHTING PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 16.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, page 16.

MANUALLY-CONTROLLED MODELS

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire de- partment.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service techni- cian or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

WARNING:

•If fireplace has glass doors, never operate this heater with glass doors closed. If you operate heater with doors closed, heat buildup inside fire- place will cause glass to burst. Also if fireplace opening has vents at the bottom, you must open the vents before operating heater.

•You must operate this heater with a fireplace screen in place. Make sure fireplace screen is closed before running heater.

NOTICE: During initial operation of new heater, burn- ing logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.

Note: Home owners generally prefer to operate their heater with the chimney damper closed. This will put all the heat into the room. However, there may be times you will desire the full flames of the High heat setting but will find the heat output excessive. You can open the chimney damper (if you have one) fully or partially to release some of the heat.

WARNING: Damper handle will be hot if heater has been running.

1.STOP! Read the safety information starting in column 1.

2.Make sure equipment shutoff valve is fully open.

3.Press in and turn control knob clockwise to the OFF position.

For morevisit www..com

104415

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsOther gases Product IdentificationProduct Features Optional Remote Control AccessoriesLocal Codes UnpackingDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationInstallation and Clearances for VENT-FREE Operation Minimum Noncombustible Material Clearances If Not Using MantelMantel Clearances Determining Minimum Mantel Clearance When Using a HoodFloor Clearances Determining Minimum Mantel ClearanceInstalling Heater Base Assembly Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Area of Various Standard Round FluesAttaching Base to Fireplace Floor Remote-Ready Models Only External Regulator With Vent Pointing Down Connecting to GAS SupplyChecking GAS Connections Pressure Testing gas Supply Piping systemPressure Testing Heater Gas Connections Installing LogsProng Log Rear Burner Grate Lighting Instructions Operating HeaterTo Turn OFF GAS to Appliance Manual Lighting ProcedureThermostat Control Operation Shutting Off HeaterVariable Control Operation REMOTE-READY Models For Your Safety Read Before LightingControl Knob and Ignitor Button Location Thermostat Control Operation Optional Remote OperationGhrcta Series Operation Ghrc Series OperationFront Burner Flame Pattern Inspecting BurnersPilot Flame Pattern Logs Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Observed Problem Possible Cause Remedy TroubleshootingRefer to Air for Combustion and Venti Gas leak. See Warning statement Thermostat-Controlled Models Only Optional Positioning of Thermostat Sensing BulbFor Masonry and FACTORY-BUILT Metal Fireplace Remote-Ready SpecificationsService Hints Wiring Diagram Replacement PartsTechnical Service Parts Under WarrantyVariable Manually Controlled Split OAK Models Illustrated Parts BreakdownVariable MANUALLY-CONTROLLED Split OAK Models Parts ListVS30NTB and VS30PTB THERMOSTAT-CONTROLLED Models REMOTE-READY Variable Control Parts List Accessories Owners Registration Form Postage Required 104415 Warranty Information

A, C, B, A, B, C specifications

Desa A, B, C, A, C, B represent a compelling exploration of village characteristics and technologies that contribute to their unique identities and functionalities. Each desa, or village, embodies distinct features that reflect their cultural heritage, technological advancements, and socio-economic activities.

Desa A is characterized by its commitment to sustainable agriculture. The villagers employ traditional farming techniques enhanced by modern technologies, such as precision farming tools and moisture sensors. This approach not only maximizes yield but also ensures environmental protection. The village integrates permaculture principles, harmonizing crops and livestock systems. Additionally, digital platforms are utilized for market access, allowing farmers to sell their produce directly to consumers, thereby enhancing their income and reducing intermediaries.

Desa B showcases a vibrant artisanal economy. With a rich tradition of crafts, this village is known for its handmade textiles and pottery. The artisans use both age-old techniques and contemporary designs, merging tradition with innovation. Technologies like 3D printing are being introduced to create unique molds for pottery, offering greater precision and creativity. Furthermore, Desa B has developed an online marketplace, enabling local artisans to reach global customers and ensure fair trade practices.

Desa C reflects a community-centric approach, emphasizing social cooperation and mutual support. The villagers employ technologies such as community screens for sharing information and organizing events. Solar energy becomes a centerpiece, providing electricity for communal activities and enhancing the village infrastructure. Additionally, Desa C has initiated a digital literacy program, empowering villagers, especially women, with essential tech skills to participate in the digital economy.

The relationship among these desas enhances cultural exchange and resource sharing. For example, Desa A's farmers can supply organic produce to the artisans of Desa B, enriching their craft with natural dyes. Meanwhile, Desa C's commitment to community collaboration creates a supportive environment for innovation and technology adoption.

In summary, Desa A, B, C, A, C, B illustrate the profound impact of integrating traditional practices with modern technologies. Their unique main features not only promote sustainable development but also foster a sense of community and collaborative growth, demonstrating that innovation can harmoniously coexist with cultural heritage. Such a dynamic ensures resilience and adaptability in an ever-evolving world.
Top Page Image Contents