Desa A, B, C Variable Control Operation, REMOTE-READY Models For Your Safety Read Before Lighting

Page 18
Ignitor Electrode
C-clockwise

18

OPERATING HEATER (MANUALLY-CONTROLLED MODELS)

Lighting Instructions (Cont.)

Variable Control Operation

To Turn Gas Off To Appliance

Manual Lighting Procedure

OPERATING HEATER (REMOTE-READY MODELS)

For Your Safety Read Before Lighting

OPERATING HEATER

Continued

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information, starting in column 1 of page 17. If you don’t smell gas, go to the next step.

5.Press in control knob and turn counterclockwise to the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 27).

Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.With control knob pressed in, press and release ignitor but- ton. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not light, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, column 2.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7.

8. Push in and turn control knob counterclockwise

to the HI position. Both burners should light. Set control knob to desired setting.

 

 

Thermocouple

Pilot

 

 

 

Burner

Ignitor Button

Control Knob

 

 

Figure 27 - Control Knob and

Figure 28- Pilot

 

Ignitor Button Location

 

 

VARIABLE CONTROL OPERATION

The variable control valve can be set to any heat setting and flame height desired, by simply turning the control knob until that setting is attained. Even the lowest setting provides realistic flames and glowing embers from two burners. Selecting higher settings pro- duces greater heat output. This results in increased heating comfort.

WARNING: Do not operate heater between locked positions.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

1.

Press in and turn control knob clockwise

Clockwise

to the

 

HI position.

 

 

2.

Turn the control knob clockwise Clockwise

to the PILOT

 

position.

 

 

3.

Press in control knob and turn clockwise

Clockwise

to the

 

OFF position.

 

 

Shutting Off Burners Only (pilot stays lit)

1.

Turn the control knob clockwise Clockwise to the HI position.

2.

Press in and turn control knob clockwise Clockwise to the

 

PILOT position.

MANUAL LIGHTING PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, pages 17 and 18.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, column 1.

REMOTE-READY MODELS

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire de- partment.

For..com

104415

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Other gasesLocal Codes Optional Remote Control AccessoriesProduct Features UnpackingDetermining FRESH-AIR Flow for Heater Location Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Installation and Clearances for VENT-FREE OperationCheck GAS Type If Not Using Mantel Minimum Noncombustible Material ClearancesFloor Clearances Determining Minimum Mantel Clearance When Using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Area of Various Standard Round FluesAttaching Base to Fireplace Floor Remote-Ready Models Only Connecting to GAS Supply External Regulator With Vent Pointing DownPressure Testing gas Supply Piping system Checking GAS ConnectionsInstalling Logs Pressure Testing Heater Gas ConnectionsProng Log Rear Burner Grate Operating Heater Lighting InstructionsThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS to Appliance Shutting Off HeaterREMOTE-READY Models For Your Safety Read Before Lighting Variable Control OperationControl Knob and Ignitor Button Location Optional Remote Operation Thermostat Control OperationGhrc Series Operation Ghrcta Series OperationInspecting Burners Pilot Flame PatternFront Burner Flame Pattern Cleaning Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleLogs Troubleshooting Observed Problem Possible Cause RemedyRefer to Air for Combustion and Venti Gas leak. See Warning statement Optional Positioning of Thermostat Sensing Bulb For Masonry and FACTORY-BUILT Metal FireplaceThermostat-Controlled Models Only Specifications Remote-ReadyTechnical Service Wiring Diagram Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Variable Manually Controlled Split OAK ModelsParts List Variable MANUALLY-CONTROLLED Split OAK ModelsVS30NTB and VS30PTB THERMOSTAT-CONTROLLED Models REMOTE-READY Variable Control Parts List Accessories Owners Registration Form Postage Required 104415 Warranty Information

A, C, B, A, B, C specifications

Desa A, B, C, A, C, B represent a compelling exploration of village characteristics and technologies that contribute to their unique identities and functionalities. Each desa, or village, embodies distinct features that reflect their cultural heritage, technological advancements, and socio-economic activities.

Desa A is characterized by its commitment to sustainable agriculture. The villagers employ traditional farming techniques enhanced by modern technologies, such as precision farming tools and moisture sensors. This approach not only maximizes yield but also ensures environmental protection. The village integrates permaculture principles, harmonizing crops and livestock systems. Additionally, digital platforms are utilized for market access, allowing farmers to sell their produce directly to consumers, thereby enhancing their income and reducing intermediaries.

Desa B showcases a vibrant artisanal economy. With a rich tradition of crafts, this village is known for its handmade textiles and pottery. The artisans use both age-old techniques and contemporary designs, merging tradition with innovation. Technologies like 3D printing are being introduced to create unique molds for pottery, offering greater precision and creativity. Furthermore, Desa B has developed an online marketplace, enabling local artisans to reach global customers and ensure fair trade practices.

Desa C reflects a community-centric approach, emphasizing social cooperation and mutual support. The villagers employ technologies such as community screens for sharing information and organizing events. Solar energy becomes a centerpiece, providing electricity for communal activities and enhancing the village infrastructure. Additionally, Desa C has initiated a digital literacy program, empowering villagers, especially women, with essential tech skills to participate in the digital economy.

The relationship among these desas enhances cultural exchange and resource sharing. For example, Desa A's farmers can supply organic produce to the artisans of Desa B, enriching their craft with natural dyes. Meanwhile, Desa C's commitment to community collaboration creates a supportive environment for innovation and technology adoption.

In summary, Desa A, B, C, A, C, B illustrate the profound impact of integrating traditional practices with modern technologies. Their unique main features not only promote sustainable development but also foster a sense of community and collaborative growth, demonstrating that innovation can harmoniously coexist with cultural heritage. Such a dynamic ensures resilience and adaptability in an ever-evolving world.
Top Page Image Contents