Desa A, C, B, A, B, C installation manual Product Identification, Other gases

Page 3

SAFETY INFORMATION PRODUCT IDENTIFICATION

3

SAFETY INFORMATION

Continued

1.

This appliance is only for use with the type of gas indicated on

 

the rating plate. This appliance is not convertible for use with

 

other gases.

2.

Do not place propane/LP supply tank(s) inside any structure. Lo-

 

cate propane/LP supply tank(s) outdoors (propane/LP units only).

3.

If you smell gas

 

shut off gas supply

 

do not try to light any appliance

 

do not touch any electrical switch; do not use any phone in

 

 

your building

 

• immediately call your gas supplier from a neighbor’s phone.

 

 

Follow the gas supplier’s instructions

 

• if you cannot reach your gas supplier, call the fire department

4.

This heater shall not be installed in a bedroom or bathroom,

 

unless installed as a vented appliance. See Installing Damper

 

Clamp Accessory for Vented Operation, page 10 (Remote-

 

Ready and Variable Manually-Controlled Models Only).

5.

Before installing in a solid fuel burning fireplace, the chimney

 

flue and firebox must be cleaned of soot, creosote, ashes and

14.Turn heater off and let cool before servicing, installing, or re- pairing. Make sure the selector switch is in the OFF position (Remote-Ready Models Only). Only a qualified service per- son should install, service, or repair heater.

15.Make sure the selector switch is in the OFF position when you are away from home for long periods of time (Remote-Ready Mod- els Only).

16.Remote-Ready heaters do not to be connected to any external electrical source.

17.Operating heater above elevations of 4,500 feet may cause pi- lot outage.

18.To prevent performance problems, do not use propane/LP fuel tank of less than 100 lb. capacity (propane/LP units only).

19.Provide adequate clearances around air openings.

PRODUCT IDENTIFICATION

Crossover Log

Rear Log

loose paint by a qualified chimney cleaner. Creosote will ig-

nite if highly heated. Inspect chimney flue for damage.

If damaged, repair flue damper before operating heater.

6. If fireplace has glass doors, never operate this heater with glass

doors closed. If you operate heater with doors closed, heat

buildup inside fireplace will cause glass to burst. Also if fire-

place opening has vents at the bottom, you must open the vents

Front Log

Rear Burner

Middle

Log

 

before operating heater.

7.

To prevent the creation of soot, follow the instructions in Clean-

 

ing and Maintenance, page 23.

8.

Before using furniture polish, wax, carpet cleaner, or similar

 

products, turn heater off. If heated, the vapors from these prod-

 

ucts may create a white powder residue within burner box or

 

on adjacent walls and furniture.

9.

This heater needs fresh, outside air ventilation to run properly.

 

This heater has an Oxygen Depletion Sensing (ODS) safety

 

shutoff system. The ODS shuts down the heater if enough fresh

 

air is not available. See Air for Combustion and Ventilation,

 

pages 4 through 6. If heater keeps shutting off, see Trouble-

 

shooting, pages 24 through 26.

10.

Do not run heater

 

where flammable liquids or vapors are used or stored

 

under dusty conditions

11.

Do not use this heater to cook food or burn paper or other objects.

12.

Do not use heater if any part has been exposed to or under

 

water. Immediately call a qualified service technician to in-

 

spect the room heater and to replace any part of the control

 

system and any gas control which has been under water.

13.

Do not operate heater if any log is broken. Do not operate

 

heater if a log is chipped (dime-sized or larger).

Piezo Ignitor

Front Burner

 

Control Knob

Base

Assembly

Front Burner

Crossover Log

 

 

Rear Log

Front Log

Rear Burner

 

Piezo

 

Ignitor

 

Remote

Middle Log

Control

 

(Optional)

 

Control

 

Knob

 

Flame Adjustment Knob

Base Assembly

 

Selector Switch (Optional)

Figure 1 - Product Identification

 

For morevisit www..com

104415

Image 3
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsOther gases Product IdentificationUnpacking Optional Remote Control AccessoriesProduct Features Local CodesDetermining FRESH-AIR Flow for Heater Location Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Installation and Clearances for VENT-FREE OperationCheck GAS Type Minimum Noncombustible Material Clearances If Not Using MantelDetermining Minimum Mantel Clearance Determining Minimum Mantel Clearance When Using a HoodMantel Clearances Floor ClearancesArea of Various Standard Round Flues Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Installation Items NeededAttaching Base to Fireplace Floor Remote-Ready Models Only External Regulator With Vent Pointing Down Connecting to GAS SupplyChecking GAS Connections Pressure Testing gas Supply Piping systemPressure Testing Heater Gas Connections Installing LogsProng Log Rear Burner Grate Lighting Instructions Operating HeaterShutting Off Heater Manual Lighting ProcedureTo Turn OFF GAS to Appliance Thermostat Control OperationVariable Control Operation REMOTE-READY Models For Your Safety Read Before LightingControl Knob and Ignitor Button Location Thermostat Control Operation Optional Remote OperationGhrcta Series Operation Ghrc Series OperationInspecting Burners Pilot Flame PatternFront Burner Flame Pattern Cleaning Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleLogs Observed Problem Possible Cause Remedy TroubleshootingRefer to Air for Combustion and Venti Gas leak. See Warning statement Optional Positioning of Thermostat Sensing Bulb For Masonry and FACTORY-BUILT Metal FireplaceThermostat-Controlled Models Only Remote-Ready SpecificationsParts Under Warranty Wiring Diagram Replacement PartsService Hints Technical ServiceVariable Manually Controlled Split OAK Models Illustrated Parts BreakdownVariable MANUALLY-CONTROLLED Split OAK Models Parts ListVS30NTB and VS30PTB THERMOSTAT-CONTROLLED Models REMOTE-READY Variable Control Parts List Accessories Owners Registration Form Postage Required 104415 Warranty Information

A, C, B, A, B, C specifications

Desa A, B, C, A, C, B represent a compelling exploration of village characteristics and technologies that contribute to their unique identities and functionalities. Each desa, or village, embodies distinct features that reflect their cultural heritage, technological advancements, and socio-economic activities.

Desa A is characterized by its commitment to sustainable agriculture. The villagers employ traditional farming techniques enhanced by modern technologies, such as precision farming tools and moisture sensors. This approach not only maximizes yield but also ensures environmental protection. The village integrates permaculture principles, harmonizing crops and livestock systems. Additionally, digital platforms are utilized for market access, allowing farmers to sell their produce directly to consumers, thereby enhancing their income and reducing intermediaries.

Desa B showcases a vibrant artisanal economy. With a rich tradition of crafts, this village is known for its handmade textiles and pottery. The artisans use both age-old techniques and contemporary designs, merging tradition with innovation. Technologies like 3D printing are being introduced to create unique molds for pottery, offering greater precision and creativity. Furthermore, Desa B has developed an online marketplace, enabling local artisans to reach global customers and ensure fair trade practices.

Desa C reflects a community-centric approach, emphasizing social cooperation and mutual support. The villagers employ technologies such as community screens for sharing information and organizing events. Solar energy becomes a centerpiece, providing electricity for communal activities and enhancing the village infrastructure. Additionally, Desa C has initiated a digital literacy program, empowering villagers, especially women, with essential tech skills to participate in the digital economy.

The relationship among these desas enhances cultural exchange and resource sharing. For example, Desa A's farmers can supply organic produce to the artisans of Desa B, enriching their craft with natural dyes. Meanwhile, Desa C's commitment to community collaboration creates a supportive environment for innovation and technology adoption.

In summary, Desa A, B, C, A, C, B illustrate the profound impact of integrating traditional practices with modern technologies. Their unique main features not only promote sustainable development but also foster a sense of community and collaborative growth, demonstrating that innovation can harmoniously coexist with cultural heritage. Such a dynamic ensures resilience and adaptability in an ever-evolving world.