AquaStar 38B NG, 38B LP specifications Water Connections, Maximum Inlet GAS Flow Pressure Setting

Page 6

WARNING

Note: The burners of an instantaneous “on demand” water heater such as the AquaStar are only on at the time that hot water is actually being used, the venting stack is therefore cold except for the short durations when hot water is being used, it is therefore very important that the venting and air supply be adequate to provide a good positive draft as soon as the burners turn on.

The AquaStar 38B instantaneous water heaters have built- in draft diverters and are designed for indoor installation only. The draft diverter outlet must be connected to a clear, unobstructed vent of the same size, or larger.

In Canada, CAN/CGA-B149 Installation Code for detailed requirements

In U.S.A., ANSI Z223.1 - NFPA 54, national Fuel Gas Code for detailed requirements.

GAS CONNECTIONS and Gas Regulator

Before connecting the gas supply, check the rating plate on the right side of the front cover to be sure that the heater is rated for the same gas to which it will be connected.

In the United States: The installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code ANSI Z223.1/NFPA 54.

In Canada: The Installation should conform with CGA B149 INSTALLATION CODES and /or local installation codes.

NOTE: The Aquastar 38 B is supplied with a gas pressure regulator that must be installed on the heater before attaching the gas supply line. See figure 2. Place the gas regulator between the gas supply connection (wich comes with a manual shutoff valve) and the gas fitting wich is connected to the heater’s gas inlet. There is a pressure test nipple on this gas fitting. The regulator supplied with the heater is preset for the gas shown on the rating plate to the correct pressure. It is an appliance level regulator designed for (low inlet) pressure (less than 1/2 Psig or 15” W.C.) DO NOT connect to an unregulated or high pressure propane line or to a high pressure commercial natural gas line.

PRESSURE REGULATOR

Fig. 2 - Gas Pressure Regulator

The pressure regulator provided with the heater is adjusted to deliver the proper gas pressure (as indicated on the rating plate and in the manual for altitude up to 2000 feet (660 meters) above sea level. On appliances being installed above 2000 ft (660 meters) elevation, the inlet gas pressure should be set at installation to the value shown below.

NOTE: The gas pressures specified below refer to pressures taken at the test pressure nipple on the gas inlet pipe just above the regulator (See Fig 2). These readings should be taken while the heater is operating at full input — i.e. maximum water flow with the temperature dial selector turned all the way clockwise.

MAXIMUM INLET GAS FLOW PRESSURE SETTING

Altitude

Natural Gas

Liquid Propane

 

inches W.C:

inches W.C:

0' - 2.000 ft

5.7"

10.5"

2.000 ft - 4.500 ft

4.6"

8.5"

Above 4.500 ft consult your local gas supplier.

National Fuel Gas Code requires that a sediment trap (drip leg) be installed on gas appliances not so equipped. The drip leg must be accessible and not subject to freezing conditions. Install in accordance with the recommendations of the serving gas supplier.

WARNING: The heater and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 0.5 psig.

The water heater must be isolated from the gas supply piping system by closing the manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 0.5 psig.

The water heater, including the pressure regulator provided with it, must not be operated at gas supply pressures in excess of 0.5 psig. If overpressure has occurred, such as through improper testing of the gas lines or emergency malfunction of the supply system, the gas valve and regulator must be checked for safe operation. Make sure that the regulator vent is protected against blockage. Vent blockage could occur during ice storms.

When your connections are made, check for gas leaks at all joints (not just the ones you made). Apply some soapy water to all gas fittings and gas valve. Soap bubbles are a sign of a leak.

NOTE: Do not apply soap solution to pilot filter screen or pilot orifice area. If you have a leak, shut off the gas. After verifying that required gaskets are in place, tighten appropriate fittings to stop leak. Turn the gas on and check again with a soapy solution. Never test for gas leaks using a match or flame.

WATER CONNECTIONS

Although water piping throughout your structure may be other than copper, we recommend that copper piping be used for at least three feet before and after the heater (follow local codes if more stringent). Keep water inlet pipe

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For Your Safety Table of ContentsWhat to do if YOU Smell GAS Features AquaStar 38B LP and 38B NG SpecificationsUnpacking the Aquastar Heater Open loop potable water and combination space heating system Combustion AIR Requirement Proper Location for Installing Your HeaterGeneral Rules to Follow For Safe Operation Could FreezeMounting Installation ClearancesVenting Altitude Natural Gas Liquid Propane Maximum Inlet GAS Flow Pressure SettingWater Connections Above 4.500 ft consult your local gas supplierFor Your Safety Read Before Lighting the Pilot Operating InstructionsSetting the Water Temperature Lighting InstructionsTo Turn OFF GAS to Appliance Maintenance and Service Characteristic Pilot FlameTrouble Shooting Pilot Lights but Flame Goes OUT When Button is ReleasedBurners do not Ignite When HOT Water is Turned on Water is TOO HOTWater is not HOT Enough HOT Water Temperature Fluctuates Unbalanced pressure in waterlinesInsufficient gas pressure Diagram of AquaStar 38 B Interior Components Diagram and Parts List Interior Components Diagram Parts List 38B LPGInstallation Checklist Controlled Energy Corp

38B LP, 38B NG specifications

The AquaStar 38B LP and AquaStar 38B NG are cutting-edge water heating solutions designed for efficiency and performance, ideal for both residential and commercial applications. These models boast a sleek, compact design, making them suitable for installation in tight spaces while still delivering robust heating capabilities.

One of the key features of the AquaStar 38B LP and 38B NG is their advanced energy efficiency. With an impressive Energy Factor (EF) rating, these units utilize state-of-the-art heat exchange technology to maximize heat transfer and minimize energy consumption. This translates to reduced utility bills and a smaller carbon footprint, making them eco-friendly options in today’s sustainability-focused market.

The AquaStar models are available in two fuel types: LP (liquefied propane) and NG (natural gas). This dual-fuel flexibility allows users to select the ideal option based on availability and cost, ensuring optimal performance tailored to individual needs. The integration of high-quality burners further enhances the efficiency and reliability of these systems, ensuring quick recovery times and consistent hot water availability.

One notable characteristic of the AquaStar 38B units is their ability to provide continuous hot water. This makes them an excellent choice for households with high demand or commercial establishments like restaurants and hotels, where hot water is required throughout the day.

Moreover, the AquaStar 38B models are equipped with innovative safety features to enhance user protection. The built-in temperature control mechanism allows users to set their preferred water temperature, while also incorporating anti-scald technology to prevent overheating.

In terms of maintenance, the AquaStar 38B units stand out with their user-friendly design. Routine maintenance is straightforward, and the models feature easily accessible components for servicing, which contributes to their longevity and reliability.

In conclusion, the AquaStar 38B LP and 38B NG represent a fusion of efficiency, safety, and advanced technology. With their energy-saving capabilities, versatile fuel options, and robust design, these water heaters are a worthwhile investment for anyone seeking reliable and efficient hot water solutions.
Top Page Image Contents