Bradford-White Corp Powered Direct Vent Series instruction manual Venting System Condensation

Page 12

Venting continued-

Venting System Condensation

Condensate formation does not occur in all installations of power vented heaters, but should be protected against on installations where condensation can form in the venting system.

Formation of condensation in the venting system of Power Vented water heaters is dependent upon installation conditions including, but not limited to:

ambient temperature and humidity of installation location;

ambient temperature and humidity of venting space;

vent distance and slope; and product usage.

In order to effectively control condensate from adversely affecting the mechanical components of the water heater several methods may be employed:

1.For horizontal installations the vent pipe can be installed with a downward slope (not less than 1/8" nor greater than ½” per foot maximum) and away from the blower motor.

2.In order to prevent condensate from draining back into the blower (vertical or horizontal runs), a fitting and drain hose is available as a condensate trap kit (see Table 1 for service part numbers). The all rubber fitting with drain outlet mounts directly to the blower motor outlet and is secured with two hose clamps (one to the blower motor outlet and the other to the vent connector). The plastic tubing is provided to drain any accumulated condensate away from the water heater and to a suitable drain. The kit comes complete with instructions for proper installation of the fitting.

Table 1

Model

Service Part

2” (5.1 cm) Blower Outlet (exhaust)

239-42742-00

3” (7.6 cm) Blower Outlet (exhaust)

239-42743-00

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Powered Direct Vent Series GAS-FIRED Water Heater For Your SafetyCongratulations Table of Contents General Information Installation Locating The Water HeaterIf YOU Smell GAS Installation Locating The Water Heater Installation Minimum Clearances Exceptions For Installations in Canada Venting Vent Assembly Illustration Venting System Condensation Venting To calculate total equivalent feet Venting Vent Connector Lengths Through the Wall Venting Through the Wall Venting with LOW Ground Clearance LOW Ground Clearance Installations Reduce 10.1 cm to 7.6 cmElbows with 1 90 Elbow 90 ft 27.5 m Through the Roof Venting Vertical Venting Page High Altitude Lengths Certain IT is Filled with Water Water Connections Water Connections Match or Open Flame for Testing Electrical Connections Electrical Connections Figure General Operation To Fill the Water HeaterLighting and Shutdown Instructions Thermostat Adjustment Burner Flame Check Maintenance Maintenance Maintenance Parts List Drawing Part Name and DescriptionDiptube Nipple Blower Parts Drawing Page Vent Pipe Preparation and Joining Vent Pipe Preparation and joining

Powered Direct Vent Series specifications

Bradford-White Corp is a leader in the manufacturing of innovative water heating and storage solutions, and its Powered Direct Vent Series exemplifies this commitment to quality, efficiency, and cutting-edge technology. These units are designed to provide reliable, consistent hot water while ensuring safety and efficiency in a variety of applications.

One of the standout features of the Powered Direct Vent Series is its forced draft system. This technology allows for the efficient removal of combustion gases, creating a safer environment indoors while allowing for flexible venting options. The powered venting system enables installations in locations where traditional venting may be impractical, such as lower-level basements or confined spaces. Homeowners can now enjoy the benefits of a high-efficiency water heater without the constraints imposed by venting through walls or roofs.

Efficiency is at the forefront of the Powered Direct Vent Series, boasting an Energy Factor (EF) that meets or exceeds industry standards. These units utilize a combination of advanced insulation and heat exchange technology to reduce standby heat loss. This means that less energy is wasted, leading to lower utility bills and a reduced carbon footprint. The series also features options designed for a range of fuel types, including natural gas and propane, catering to the diverse needs of different households.

Durability is another key characteristic of the Bradford-White Powered Direct Vent Series. Each unit is constructed with high-quality materials, including a robust tank with a glass-lined interior to resist corrosion. This ensures longevity and reliable performance over the lifespan of the system. Additionally, the units are equipped with advanced safety features, such as a high-temperature limit switch and a flame arrestor, which provide peace of mind for homeowners.

The user-friendly controls and diagnostics on these models make them easy to monitor and maintain. With built-in LED indicators and self-diagnostics, homeowners and service technicians can quickly assess the unit's performance and troubleshoot any issues that may arise. This ensures that hot water is always available when needed, enhancing overall convenience.

In summary, the Bradford-White Powered Direct Vent Series combines advanced technology, high efficiency, and durable construction to deliver exceptional water heating solutions. With features tailored for safety and convenience, these units are an excellent choice for any home seeking a reliable and energy-efficient hot water solution.
Top Page Image Contents