Bradford-White Corp Powered Direct Vent Series instruction manual Certain IT is Filled with Water

Page 24

Water Connections

Note: BEFORE PROCEEDING WITH THE INSTALLATION, CLOSE THE MAIN WATER SUPPLY VALVE.

After shutting off the main water supply, open a faucet to relieve the water line pressure to prevent any water from leaking out of the pipes while making the water connections to the water heater. After the pressure has been relieved, close the faucet. The COLD water inlet and HOT water outlet are identified on the top of the water heater. The fittings at the cold-water inlet and hot water outlet are dielectric waterway fittings with 3/4” (1.9 cm) NPT male thread. Make the proper plumbing connections between the water heater and the plumbing system to the house. Install a shut-off valve in the cold water supply line.

CAUTION

If sweat fittings are to be used DO NOT apply heat to the nipples on top of the water heater. Sweat the tubing to the adapter before fitting the adapter to the water connections. It is imperative that heat is not applied to the nipples containing a plastic liner.

WARNING

FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED 3/4” X 3/4”

TEMPERATURE AND PRESSURE RELIEF VALVE WILL RELEASE THE MANUFACTURER FROM ANY CLAIM, WHICH MIGHT RESULT FROM EXCESSIVE TEMPERATURE AND PRESSURES.

If this water heater is installed in a closed water supply system, such as one having a back-flow preventer in the cold water supply, provisions must be made to control thermal expansion. DO NOT operate this water heater in a closed system without provisions for controlling thermal expansion. Your water supplier or local plumbing inspector should be contacted on how to control this situation

After installation of the water lines, open the main water supply valve and fill the water heater. While the water heater is filling, open several hot water faucets to allow air to escape from the water system. When a steady stream of water flows through the faucets, close them and check all water connections for possible leaks. NEVER OPERATE THE WATER HEATER WITHOUT FIRST BEING

CERTAIN IT IS FILLED WITH WATER.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Powered Direct Vent Series GAS-FIRED Water Heater For Your SafetyCongratulations Table of Contents General Information Installation Locating The Water HeaterIf YOU Smell GAS Installation Locating The Water Heater Installation Minimum Clearances Exceptions For Installations in Canada Venting Vent Assembly Illustration Venting System Condensation Venting To calculate total equivalent feet Venting Vent Connector Lengths Through the Wall Venting Through the Wall Venting with LOW Ground Clearance LOW Ground Clearance Installations Reduce 10.1 cm to 7.6 cmElbows with 1 90 Elbow 90 ft 27.5 m Through the Roof Venting Vertical Venting Page High Altitude Lengths Certain IT is Filled with Water Water Connections Water Connections Match or Open Flame for Testing Electrical Connections Electrical Connections Figure General Operation To Fill the Water HeaterLighting and Shutdown Instructions Thermostat Adjustment Burner Flame Check Maintenance Maintenance Maintenance Parts List Drawing Part Name and DescriptionDiptube Nipple Blower Parts Drawing Page Vent Pipe Preparation and Joining Vent Pipe Preparation and joining

Powered Direct Vent Series specifications

Bradford-White Corp is a leader in the manufacturing of innovative water heating and storage solutions, and its Powered Direct Vent Series exemplifies this commitment to quality, efficiency, and cutting-edge technology. These units are designed to provide reliable, consistent hot water while ensuring safety and efficiency in a variety of applications.

One of the standout features of the Powered Direct Vent Series is its forced draft system. This technology allows for the efficient removal of combustion gases, creating a safer environment indoors while allowing for flexible venting options. The powered venting system enables installations in locations where traditional venting may be impractical, such as lower-level basements or confined spaces. Homeowners can now enjoy the benefits of a high-efficiency water heater without the constraints imposed by venting through walls or roofs.

Efficiency is at the forefront of the Powered Direct Vent Series, boasting an Energy Factor (EF) that meets or exceeds industry standards. These units utilize a combination of advanced insulation and heat exchange technology to reduce standby heat loss. This means that less energy is wasted, leading to lower utility bills and a reduced carbon footprint. The series also features options designed for a range of fuel types, including natural gas and propane, catering to the diverse needs of different households.

Durability is another key characteristic of the Bradford-White Powered Direct Vent Series. Each unit is constructed with high-quality materials, including a robust tank with a glass-lined interior to resist corrosion. This ensures longevity and reliable performance over the lifespan of the system. Additionally, the units are equipped with advanced safety features, such as a high-temperature limit switch and a flame arrestor, which provide peace of mind for homeowners.

The user-friendly controls and diagnostics on these models make them easy to monitor and maintain. With built-in LED indicators and self-diagnostics, homeowners and service technicians can quickly assess the unit's performance and troubleshoot any issues that may arise. This ensures that hot water is always available when needed, enhancing overall convenience.

In summary, the Bradford-White Powered Direct Vent Series combines advanced technology, high efficiency, and durable construction to deliver exceptional water heating solutions. With features tailored for safety and convenience, these units are an excellent choice for any home seeking a reliable and energy-efficient hot water solution.
Top Page Image Contents