Bradford-White Corp Powered Direct Vent Series instruction manual Through the Wall Venting

Page 17

Venting continued-

IMPORTANT

All of the Venting connections must be leak checked with a soap and water solution upon initial start up of the water heater. Any leaks must be repaired before continuing operation of the water heater.

NOTE: ABS or CPVC pipes may be substituted for PVC pipe. Do not mix

ABS and PVC pipe in the same installation.

THROUGH THE WALL VENTING:

Cut a 3 1/2 in. (8.9 cm) diameter hole in the wall at the point where the vent connector is going to pass through the wall. Use the proper cement to secure the 90° vent terminal provided with the water heater to the vent connector. The distance between the edge of the 90° vent terminal and the exterior wall (see Figure 5) must be at least 1 in. (2.5 cm). The exhaust and intake terminals must not be less than 16 in. (40.6 cm) apart (see Figure 7). The exhaust terminal must not be mounted below the intake terminal. Use the proper cement and assembly procedures to secure the vent connector joints between the terminal and the blower outlet. Provide support brackets for every 3 feet (.91 m) of horizontal vent.

Figure 5

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents For Your Safety Powered Direct Vent Series GAS-FIRED Water HeaterCongratulations Table of Contents General Information Locating The Water Heater InstallationIf YOU Smell GAS Installation Locating The Water Heater Installation Minimum Clearances Exceptions For Installations in Canada Venting Vent Assembly Illustration Venting System Condensation Venting To calculate total equivalent feet Venting Vent Connector Lengths Through the Wall Venting Through the Wall Venting with LOW Ground Clearance Reduce 10.1 cm to 7.6 cm LOW Ground Clearance InstallationsElbows with 1 90 Elbow 90 ft 27.5 m Through the Roof Venting Vertical Venting Page High Altitude Lengths Certain IT is Filled with Water Water Connections Water Connections Match or Open Flame for Testing Electrical Connections Electrical Connections Figure To Fill the Water Heater General OperationLighting and Shutdown Instructions Thermostat Adjustment Burner Flame Check Maintenance Maintenance Maintenance Part Name and Description Parts List DrawingDiptube Nipple Blower Parts Drawing Page Vent Pipe Preparation and Joining Vent Pipe Preparation and joining

Powered Direct Vent Series specifications

Bradford-White Corp is a leader in the manufacturing of innovative water heating and storage solutions, and its Powered Direct Vent Series exemplifies this commitment to quality, efficiency, and cutting-edge technology. These units are designed to provide reliable, consistent hot water while ensuring safety and efficiency in a variety of applications.

One of the standout features of the Powered Direct Vent Series is its forced draft system. This technology allows for the efficient removal of combustion gases, creating a safer environment indoors while allowing for flexible venting options. The powered venting system enables installations in locations where traditional venting may be impractical, such as lower-level basements or confined spaces. Homeowners can now enjoy the benefits of a high-efficiency water heater without the constraints imposed by venting through walls or roofs.

Efficiency is at the forefront of the Powered Direct Vent Series, boasting an Energy Factor (EF) that meets or exceeds industry standards. These units utilize a combination of advanced insulation and heat exchange technology to reduce standby heat loss. This means that less energy is wasted, leading to lower utility bills and a reduced carbon footprint. The series also features options designed for a range of fuel types, including natural gas and propane, catering to the diverse needs of different households.

Durability is another key characteristic of the Bradford-White Powered Direct Vent Series. Each unit is constructed with high-quality materials, including a robust tank with a glass-lined interior to resist corrosion. This ensures longevity and reliable performance over the lifespan of the system. Additionally, the units are equipped with advanced safety features, such as a high-temperature limit switch and a flame arrestor, which provide peace of mind for homeowners.

The user-friendly controls and diagnostics on these models make them easy to monitor and maintain. With built-in LED indicators and self-diagnostics, homeowners and service technicians can quickly assess the unit's performance and troubleshoot any issues that may arise. This ensures that hot water is always available when needed, enhancing overall convenience.

In summary, the Bradford-White Powered Direct Vent Series combines advanced technology, high efficiency, and durable construction to deliver exceptional water heating solutions. With features tailored for safety and convenience, these units are an excellent choice for any home seeking a reliable and energy-efficient hot water solution.
Top Page Image Contents