Bradford-White Corp Powered Direct Vent Series instruction manual Maintenance

Page 34

MAINTENANCE

WARNING

Water heaters are heat-producing appliances. To avoid damage or injury there must be no materials stored against the water heater or vent-air intake system, and proper care must be taken to avoid unnecessary contact (especially by children) with the water heater and vent-air intake system.

UNDER NO CIRCUMSTANCES MUST FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.

IMPORTANT

The water heater should be inspected at a minimum annually by a qualified service technician for damaged components and/or joints not sealed. DO NOT operate this water heater if any part is found damaged or if any joint is found not sealed.

A qualified service technician should perform the following maintenance at the minimum periodic intervals suggested below. In some installations, the maintenance interval may be more frequent depending on the amount of use and the operating conditions of the water heater. Regular inspection and maintenance of the water heater and vent-air intake system will help to insure safe and reliable operation.

1.Annually check the operation of the thermostat.

2.The flow of combustion and ventilation air MUST NOT be restricted. Clear the combustion air openings of any dirt, dust, or other restrictions.

WAR I G! The ventilation air system may be HOT.

3. At all times keep the water heater area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

4.Bi-annually conduct a visual check of the main and pilot burner flames to determine that they are burning properly. See Burner Flame Check section on page 31. If sooting or other burner anomalies are evident, shut down the water heater by turning off the gas per the instructions listed in this manual or as listed on the water heater.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Powered Direct Vent Series GAS-FIRED Water Heater For Your SafetyCongratulations Table of Contents General Information Installation Locating The Water HeaterIf YOU Smell GAS Installation Locating The Water Heater Installation Minimum Clearances Exceptions For Installations in Canada Venting Vent Assembly Illustration Venting System Condensation Venting To calculate total equivalent feet Venting Vent Connector Lengths Through the Wall Venting Through the Wall Venting with LOW Ground Clearance LOW Ground Clearance Installations Reduce 10.1 cm to 7.6 cmElbows with 1 90 Elbow 90 ft 27.5 m Through the Roof Venting Vertical Venting Page High Altitude Lengths Certain IT is Filled with Water Water Connections Water Connections Match or Open Flame for Testing Electrical Connections Electrical Connections Figure General Operation To Fill the Water HeaterLighting and Shutdown Instructions Thermostat Adjustment Burner Flame Check Maintenance Maintenance Maintenance Parts List Drawing Part Name and DescriptionDiptube Nipple Blower Parts Drawing Page Vent Pipe Preparation and Joining Vent Pipe Preparation and joining

Powered Direct Vent Series specifications

Bradford-White Corp is a leader in the manufacturing of innovative water heating and storage solutions, and its Powered Direct Vent Series exemplifies this commitment to quality, efficiency, and cutting-edge technology. These units are designed to provide reliable, consistent hot water while ensuring safety and efficiency in a variety of applications.

One of the standout features of the Powered Direct Vent Series is its forced draft system. This technology allows for the efficient removal of combustion gases, creating a safer environment indoors while allowing for flexible venting options. The powered venting system enables installations in locations where traditional venting may be impractical, such as lower-level basements or confined spaces. Homeowners can now enjoy the benefits of a high-efficiency water heater without the constraints imposed by venting through walls or roofs.

Efficiency is at the forefront of the Powered Direct Vent Series, boasting an Energy Factor (EF) that meets or exceeds industry standards. These units utilize a combination of advanced insulation and heat exchange technology to reduce standby heat loss. This means that less energy is wasted, leading to lower utility bills and a reduced carbon footprint. The series also features options designed for a range of fuel types, including natural gas and propane, catering to the diverse needs of different households.

Durability is another key characteristic of the Bradford-White Powered Direct Vent Series. Each unit is constructed with high-quality materials, including a robust tank with a glass-lined interior to resist corrosion. This ensures longevity and reliable performance over the lifespan of the system. Additionally, the units are equipped with advanced safety features, such as a high-temperature limit switch and a flame arrestor, which provide peace of mind for homeowners.

The user-friendly controls and diagnostics on these models make them easy to monitor and maintain. With built-in LED indicators and self-diagnostics, homeowners and service technicians can quickly assess the unit's performance and troubleshoot any issues that may arise. This ensures that hot water is always available when needed, enhancing overall convenience.

In summary, the Bradford-White Powered Direct Vent Series combines advanced technology, high efficiency, and durable construction to deliver exceptional water heating solutions. With features tailored for safety and convenience, these units are an excellent choice for any home seeking a reliable and energy-efficient hot water solution.
Top Page Image Contents