Genie 3627336241 warranty Genie, Safe-T-Beam System Self-Diagnostic Troubleshooting, BLINKS, Pause

Page 10

MAINTENANCE

AMonthly:

•Door springs and door hardware:

–Oil door roller, bearings, and hinges using silicone lubricant or light oil..

WARNING

Do not operate door automatically or manually if springs are broken.. Contact a Genie Factory Authorized Dealer for service or call Customer Service at 1-800-35-GENIE..

•Balance Door..

–Close door.

–Release Magnetic Carriage Assembly from Rail Assembly by pulling down on Emergency Release Knob..

–Raise door manually 3’- 4’ and verify that door stays at that position.. See Check Step 2 on page 4..

NOTE

When the door is 3’ - 4’ above the ground, the door should stay open.. Slight movement is acceptable.. If the door moves too much, contact a Genie Factory Authorized Dealer for service or call Customer Service at

1-800-35-GENIE.

–Reattach Magnetic Carriage Assembly to Rail Assembly by pulling the Emergency Release Knob toward Power Head..

–Close door..

•Contact Reverse Test.

–Perform Adjustment 2 on page 8..

WARNING

If the door fails to reverse on contact with the board, adjust the Close Force Control as specified in Set Limit Switches and Force Controls on page 7.. If the Opener still fails, contact a Genie Factory Authorized Dealer for service or call Customer Service at 1-800-35-GENIE..

BYearly:

•Wipe off old excess lubricant from Drive Screw.

•Lubricate Drive Screw with Genie Lubricant (GLU-3)

NOTE

Use ONLY Genie Lubricant (GLU-3).. Other lubricants may damage the Opener..

 

 

Garage

GLU-3

Drive Lubricant

Door Part

 

 

ScrewOpenerGLU-3

 

 

No.

Lubricant

FCC AND IC CERTIFIED

All devices comply with Part 15 of the FCC Rules.. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation..

Troubleshooting Guide

Safe-T-Beam® System Self-Diagnostic Troubleshooting

Source (Red LED)

Sensor (Green LED)

Possible Problem

Solution

ON

ON

Normal operation

None required

OFF

OFF

• Power Head not powered

• Check breakers, fuses, plugs

• Wiring from Power Head bad

• Check wiring for obvious shorts

 

 

OFF

ON

• Wiring to Source missing or bad

• Check wiring

• Power has been interrupted

• Remove power and reapply

 

 

2 BLINKS, Pause

 

• Beam not aligned

• Check Source, Sensor alignment

(Repeat)

ON

• Beam obstructed

• Check for obstruction

 

 

• Sensor defective

• Contact Customer Service

2 BLINKS, Pause

OFF

• Wire to Sensor missing or bad

• Check wiring

(Repeat)

• Sensor defective

• Contact Customer Service

 

3 BLINKS, Pause

ON

• Sensor receiving interference

• Determine source of interference

(Repeat)

 

• Contact Customer Service

 

 

4 BLINKS, Pause

ON

• Source not sending pulses

• Contact Customer Service

(Repeat)

• Source defective

• Contact Customer Service

 

 

 

 

 

10

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DC Powered Screw Drive Opener Service From Authorized Dealers Manual 1 Warranty InformationGenie Company Limited Warranty What this warranty does not coverSafety Features Instructions­Tools used in this section Check following items before assembling OpenerMounting Area Check Check Ceiling for Grounded Power SourceMounting Bracket Location Wood for header, ceiling, and/or door braces store Check Recommended toolsCheck emove xisting arage Door Locks Test Opener monthly.. The door Must reverse on contact withDo Not Unplug the Unit simply wait Little effort is required to turn the Force Adjusting KnobsAdjustment 1 Adjusting Limit Switches and Force Controls On pgTransmitter Compliance Statement AccessoriesEach Remote Control must be programmed separately Moving garage door may cause serious injury or deathTo Erase All Remotes from Power Head Memory Install Light Bulbs and LensRemote Control Operation To Replace Remote Control BatteryGenie Safe-T-Beam System Self-Diagnostic TroubleshootingSource Red LED Sensor Green LED Possible Problem Solution BLINKS, PauseCheck door condition.. Note This Opener is equipped with an You See Problem What to Do ReferenceDoor hardware or rollers may result in a ONE-BLINK signal OpenerGeneral Troubleshooting Always Check the Status LED Light Problem What To DoWiring Diagram Opening Cover May Result in Electric ShockQuantity Power Head Assembly Exploded ViewPart Name Hardware Exploded View Ordering Instructions Instructions CommandantLas Instrucciones que Ordenan

3627336241 specifications

Genie 3627336241 is a cutting-edge machine that exemplifies the perfect blend of advanced features, innovative technologies, and remarkable characteristics. Designed primarily for enhancing productivity and efficiency, this equipment is widely regarded in the construction and maintenance sectors.

One of the standout features of the Genie 3627336241 is its exceptional lifting capability. With a maximum working height of approximately 36 feet, it provides operators with the ability to access elevated areas with ease. Its robust platform can accommodate a significant workload, making it ideal for various tasks such as electrical work, painting, and installation of infrastructure.

Safety is paramount when it comes to the Genie 3627336241. Equipped with advanced safety systems, including a secure ground control, tilt-level sensors, and emergency stop features, it ensures that operators can work confidently at heights. The non-slip surface of the platform further adds an extra layer of safety, making it a reliable choice for demanding environments.

The Genie 3627336241 is powered by a highly efficient electric drive system. This technology not only enhances energy efficiency but also minimizes environmental impact, making it a sustainable option for today's eco-conscious businesses. The quiet operation of the machine allows for use in noise-sensitive environments without disturbing surrounding activities.

Mobility is another key characteristic of the Genie 3627336241. The compact design, combined with durable rubber tires, enables smooth maneuverability across various terrains. Whether navigating indoor spaces or uneven outdoor surfaces, it offers stability and ease of movement.

In terms of operator comfort, the Genie 3627336241 features an ergonomic control layout. Controls are designed for intuitive operation, reducing the learning curve for new users while enhancing productivity for experienced operators. The spacious platform also allows for multiple workers to operate simultaneously, increasing overall efficiency on job sites.

Durability is integral to the design philosophy behind the Genie 3627336241. Constructed with high-quality materials, this machine withstands the rigors of everyday use, ensuring longevity and low maintenance costs. The reinforced frame and corrosion-resistant components contribute to its reliability and performance over time.

In conclusion, the Genie 3627336241 stands as a testament to innovation in the equipment industry. With its impressive height capabilities, advanced safety features, eco-friendly operation, and user-centric design, it represents an invaluable asset for professionals seeking to enhance productivity and efficiency in their operations. This machine is engineered to meet the demands of modern workspaces, making it a preferred choice for various applications in construction and maintenance industries.
Top Page Image Contents