Genie 3627336241 warranty Mounting Area, Check Check Ceiling for Grounded Power Source

Page 5

NOTE

For all types and styles of doors:

If the ceiling in your garage is so low that there is not at least a 3” space above the Header Bracket mounting point, contact a Genie Factory Authorized Dealer.

If a door spring is in the way, place the Header Bracket above the spring.. Do Not move the door spring..

WARNING:

Door springs are under extremely high tension and should be handled ONLY by a trained professional..

CCheck wall for a stud or a solid header at your mark: (If checking a finished wall, a stud finder may be helpful)..

If location is above Header, a 2” x 6” board must be screwed to studs beside your mark with at least two Lag Screws and Flat Washers (not provided)..

Transfer your mark to new mounting board..

Check Step 5: Check Power Head

Mounting Area

Check ceiling or space above where Opener Power Head will be mounted (Figure 5): There must be a 120 Volt grounded outlet or wiring box within 3 feet of Power Head..

Grounded outlet

10’ (7’-6” door)

11’ (8’ door)

Door Center Line

Figure 5 Check Power Head location

AThe measurements above are taken from the garage door centerline toward the rear of the garage..

BFind location of ceiling joist or truss above where Opener Power Head will be and estimate type and quantity of materials needed for your installation (Figure 6A & B)..

MOUNTING EXAMPLES

Standard Straps Extra wood required Perforated Angle Iron

Figure 6A

OPEN CEILINGS Straps and angle iron may attach directly to joists or trusses..

Perforated Straps

FINISHED CEILINGS

Locate ceiling joists or trusses using a stud finder or similar device.

Attach angle iron(not included) to joists or trusses through finish material using Lag Screws..

Figure 6B Mounting methods for open beam or finished ceilings

Check Step 6: Check Ceiling for Grounded Power Source

ACheck that there is a 15 Amp 120 Volt grounded electrical outlet or grounded permanent wiring box (per building code) within 3’ of Opener Power Head: Figure 5

If not, an outlet or wiring box must be installed.. Contact a licensed electrician for installation..

If building codes require permanent wiring, Power Head must be partially disassembled to install appropriate wiring in place of Power Cord.. (See Assembly and Installation Poster..)

NOTE

Permanent wiring must be installed by a Licensed Electrician.. Not all Genie Factory Authorized Dealers

are Licensed Electrician’s.. Contact someone who is a Licensed Electrician..

WARNING:

Do Not use an extension cord! Extension cords can cause dangerous overheating conditions..

Do Not use portable generator! This product is designed to operate using standard house current.. Do Not use alternate power supplies,

Check Step 7: Check Safe-T-Beam®

Mounting Bracket Location

Check for wood garage frame, jamb, or masonry at mounting location (6” above floor) with attachment tabs facing away from garage door (Figure 7)..

AIf you cannot mount Safe-T-Beam® Mounting Bracket to wood frame:

Concrete screws and concrete anchors (not included) must be used to mount Brackets on masonry with attachment tabs facing away from garage door..

Source

 

 

Sensor

 

 

Safe-T-Beam®

Top of

Mounting Bracket

Bracket

 

 

Figure 7

Mounting

6” above

floor

 

Safe-T-Beam®

 

 

 

Components

 

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

5

Image 5
Contents DC Powered Screw Drive Opener Genie Company Limited Warranty Manual 1 Warranty InformationService From Authorized Dealers What this warranty does not coverInstructions­ Safety FeaturesCheck following items before assembling Opener Tools used in this sectionMounting Bracket Location Check Check Ceiling for Grounded Power SourceMounting Area Check emove xisting arage Door Locks Check Recommended toolsWood for header, ceiling, and/or door braces store Test Opener monthly.. The door Must reverse on contact withAdjustment 1 Adjusting Limit Switches and Force Controls Little effort is required to turn the Force Adjusting KnobsDo Not Unplug the Unit simply wait On pgEach Remote Control must be programmed separately AccessoriesTransmitter Compliance Statement Moving garage door may cause serious injury or deathRemote Control Operation Install Light Bulbs and LensTo Erase All Remotes from Power Head Memory To Replace Remote Control BatterySource Red LED Sensor Green LED Possible Problem Solution Safe-T-Beam System Self-Diagnostic TroubleshootingGenie BLINKS, PauseDoor hardware or rollers may result in a ONE-BLINK signal You See Problem What to Do ReferenceCheck door condition.. Note This Opener is equipped with an OpenerProblem What To Do General Troubleshooting Always Check the Status LED LightOpening Cover May Result in Electric Shock Wiring DiagramPart Name Power Head Assembly Exploded ViewQuantity Hardware Exploded View Las Instrucciones que Ordenan Instructions CommandantOrdering Instructions

3627336241 specifications

Genie 3627336241 is a cutting-edge machine that exemplifies the perfect blend of advanced features, innovative technologies, and remarkable characteristics. Designed primarily for enhancing productivity and efficiency, this equipment is widely regarded in the construction and maintenance sectors.

One of the standout features of the Genie 3627336241 is its exceptional lifting capability. With a maximum working height of approximately 36 feet, it provides operators with the ability to access elevated areas with ease. Its robust platform can accommodate a significant workload, making it ideal for various tasks such as electrical work, painting, and installation of infrastructure.

Safety is paramount when it comes to the Genie 3627336241. Equipped with advanced safety systems, including a secure ground control, tilt-level sensors, and emergency stop features, it ensures that operators can work confidently at heights. The non-slip surface of the platform further adds an extra layer of safety, making it a reliable choice for demanding environments.

The Genie 3627336241 is powered by a highly efficient electric drive system. This technology not only enhances energy efficiency but also minimizes environmental impact, making it a sustainable option for today's eco-conscious businesses. The quiet operation of the machine allows for use in noise-sensitive environments without disturbing surrounding activities.

Mobility is another key characteristic of the Genie 3627336241. The compact design, combined with durable rubber tires, enables smooth maneuverability across various terrains. Whether navigating indoor spaces or uneven outdoor surfaces, it offers stability and ease of movement.

In terms of operator comfort, the Genie 3627336241 features an ergonomic control layout. Controls are designed for intuitive operation, reducing the learning curve for new users while enhancing productivity for experienced operators. The spacious platform also allows for multiple workers to operate simultaneously, increasing overall efficiency on job sites.

Durability is integral to the design philosophy behind the Genie 3627336241. Constructed with high-quality materials, this machine withstands the rigors of everyday use, ensuring longevity and low maintenance costs. The reinforced frame and corrosion-resistant components contribute to its reliability and performance over time.

In conclusion, the Genie 3627336241 stands as a testament to innovation in the equipment industry. With its impressive height capabilities, advanced safety features, eco-friendly operation, and user-centric design, it represents an invaluable asset for professionals seeking to enhance productivity and efficiency in their operations. This machine is engineered to meet the demands of modern workspaces, making it a preferred choice for various applications in construction and maintenance industries.