Genie 3627336241 warranty You See Problem What to Do Reference, Opener, Overheated

Page 11

Opener System Self-Diagnostic Troubleshooting

•See Status Light on Figure MA-2, page 9)

You See

Problem

 

What to Do

Reference

1 BLINK,

Motor Drive

• Reset Opener—unplug (or disconnect power), wait 5 seconds, plug

 

 

Pause

Board

 

back in (reapply power), and activate from Wall Console.

 

 

(Repeat)

Interrupt

 

 

 

 

 

Normal

• First Cycle will run at slow speed.

 

 

 

operation

 

 

 

 

 

restored

 

 

 

 

 

 

 

 

 

 

 

If the problem

•

Check door condition.. NOTE: This Opener is equipped with an

See Door

 

recurs

 

automatic garage door balance detection system. An improperly

Safety Guide

 

 

 

balanced door, damaged or worn counter-balance spring, binding

 

 

 

 

 

door hardware or rollers may result in a “ONE-BLINK” signal.

 

 

 

 

• Contact Customer Service for further assistance..

 

 

 

Operation not

•

Check door condition.

1.. See page 4.

 

restored

• Have a Genie Factory Authorized Dealer check:

2.. See door

 

 

 

– Fuse on Motor Drive Board.

Safety Guide

 

 

 

– Ribbon Cable on Motor Drive Board is properly inserted into

 

 

 

 

 

Connector on Controller Board.

 

 

 

 

• Contact Customer service for further service..

 

 

2 BLINKS,

Controller

• Reset Opener — unplug (or disconnect power), wait 5 seconds, plug

 

 

Pause

Board

 

back in (reapply power), and activate from Wall Console.

 

 

(Repeat)

Interrupt

• Have a Genie Factory Authorized Dealer check that Ribbon Cable on

 

 

 

 

 

Motor Board is properly inserted into connector on Controller Board.

 

 

 

 

• Contact Customer Service for further assistance..

 

 

3 BLINKS,

Opener

• Do not unplug or disconnect power from Opener. Wait 10 minutes

 

 

Pause

Overheated

 

for internal clock to provide additional cycles. Cycles are restored

 

 

(Repeat)

or

 

at a rate of 5 cycles per 10 minutes of rest.

 

 

 

Over-cycled

• Contact Customer Service for further assistance.

 

 

4 BLINKS,

Force Settings

•

Check Force Settings.. NOTE: Force Settings are not pre-set at factory.

1.. See page 7.

Pause

Incorrect

•

Check door condition.

2.. See Door

(Repeat)

 

• Contact Customer service for further assistance.

Safety Guide

5BLINKS,

Safe-T-Beam®

• Check Safe-T-Beam® Self-diagnostic System.. NOTE: Safe-T-Beam®

See page 13.

Pause

Malfunction

 

System must be installed and operational to enable door to close.

 

 

 

 

• Contact Customer Service for further assistance..

 

 

6 BLINKS,

Wall Console

• Check Wall Console Wiring for shorts, tight Staples, or pinched Wires.

Assembly and

Pause

does not work

• Check Wiring Connections at Power Head and Wall Console.

Installation

(Repeat)

 

• Contact Customer Service for further assistance.

Poster..

7 BLINKS,

Limit Switches

• Check Limit Switch Wire connections to Terminals on Power Head.

Assembly and

Pause

not working

• Check for shorted or pinched Wires under Limit Switch Brackets.

Installation

(Repeat)

 

• Contact Customer Service for further assistance.

Poster..

8 BLINKS,

Wall Console

• Vacation Locking Switch on Wall Control is in “Lock” mode..

Assembly and

Pause

locked

 

Unlock switch.

Installation

(Repeat)

 

• Contact Customer Service for further assistance.

Poster..

NOTE

• The status LED Indicator Light is located under the Lens Cover. The Green LED light will turn ON, then OFF when power is applied to the Opener.. If LED stays ON, have a Genie Factory Authorized Dealer check the Controller Board, or call Customer Service at 1-800-35-GENIE.

• If Safe-T-Beam® problems exists, the door can be closed electrically by holding the Wall Console Button down until door is fully closed.

• The Remote Controls and Wireless Keypad will not work without a working Safe-T-Beam® System.

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DC Powered Screw Drive Opener What this warranty does not cover Manual 1 Warranty InformationGenie Company Limited Warranty Service From Authorized DealersInstructions­ Safety FeaturesCheck following items before assembling Opener Tools used in this sectionMounting Bracket Location Check Check Ceiling for Grounded Power SourceMounting Area Test Opener monthly.. The door Must reverse on contact with Check Recommended toolsCheck emove xisting arage Door Locks Wood for header, ceiling, and/or door braces storeOn pg Little effort is required to turn the Force Adjusting KnobsAdjustment 1 Adjusting Limit Switches and Force Controls Do Not Unplug the Unit simply waitMoving garage door may cause serious injury or death AccessoriesEach Remote Control must be programmed separately Transmitter Compliance StatementTo Replace Remote Control Battery Install Light Bulbs and LensRemote Control Operation To Erase All Remotes from Power Head MemoryBLINKS, Pause Safe-T-Beam System Self-Diagnostic TroubleshootingSource Red LED Sensor Green LED Possible Problem Solution GenieOpener You See Problem What to Do ReferenceDoor hardware or rollers may result in a ONE-BLINK signal Check door condition.. Note This Opener is equipped with anProblem What To Do General Troubleshooting Always Check the Status LED LightOpening Cover May Result in Electric Shock Wiring DiagramPart Name Power Head Assembly Exploded ViewQuantity Hardware Exploded View Las Instrucciones que Ordenan Instructions CommandantOrdering Instructions

3627336241 specifications

Genie 3627336241 is a cutting-edge machine that exemplifies the perfect blend of advanced features, innovative technologies, and remarkable characteristics. Designed primarily for enhancing productivity and efficiency, this equipment is widely regarded in the construction and maintenance sectors.

One of the standout features of the Genie 3627336241 is its exceptional lifting capability. With a maximum working height of approximately 36 feet, it provides operators with the ability to access elevated areas with ease. Its robust platform can accommodate a significant workload, making it ideal for various tasks such as electrical work, painting, and installation of infrastructure.

Safety is paramount when it comes to the Genie 3627336241. Equipped with advanced safety systems, including a secure ground control, tilt-level sensors, and emergency stop features, it ensures that operators can work confidently at heights. The non-slip surface of the platform further adds an extra layer of safety, making it a reliable choice for demanding environments.

The Genie 3627336241 is powered by a highly efficient electric drive system. This technology not only enhances energy efficiency but also minimizes environmental impact, making it a sustainable option for today's eco-conscious businesses. The quiet operation of the machine allows for use in noise-sensitive environments without disturbing surrounding activities.

Mobility is another key characteristic of the Genie 3627336241. The compact design, combined with durable rubber tires, enables smooth maneuverability across various terrains. Whether navigating indoor spaces or uneven outdoor surfaces, it offers stability and ease of movement.

In terms of operator comfort, the Genie 3627336241 features an ergonomic control layout. Controls are designed for intuitive operation, reducing the learning curve for new users while enhancing productivity for experienced operators. The spacious platform also allows for multiple workers to operate simultaneously, increasing overall efficiency on job sites.

Durability is integral to the design philosophy behind the Genie 3627336241. Constructed with high-quality materials, this machine withstands the rigors of everyday use, ensuring longevity and low maintenance costs. The reinforced frame and corrosion-resistant components contribute to its reliability and performance over time.

In conclusion, the Genie 3627336241 stands as a testament to innovation in the equipment industry. With its impressive height capabilities, advanced safety features, eco-friendly operation, and user-centric design, it represents an invaluable asset for professionals seeking to enhance productivity and efficiency in their operations. This machine is engineered to meet the demands of modern workspaces, making it a preferred choice for various applications in construction and maintenance industries.
Top Page Image Contents