Genie 1000 Belt, Chain, Corrective Maintenance Change Light Bulbs, Reset OPEN/CLOSE Travel Limit

Page 10

CORRECTIVE MAINTENANCE

CHANGE LIGHT BULBS

WARNING

sUse extreme caution when working from a ladder or step stool.

sWhen replacing light cover, make sure wires are not pinched or near moving parts.

1.Disconnect power to door opener. ss /PEN/Powerhead light cover.

ss2EMove light bulb(s).

ss2EPLAce light bulb(s).

–Do NOT use light bulbs with greater than 100 Watt rating.

ss#LOSE Powerhead light cover.

2.Reconnect power to door opener.

ssTest light operation.

RESET - OPEN/CLOSE TRAVEL LIMIT

Performing all ten (10) Limits/Force setting steps (page 5) erases previous Limits/Force settings.

NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed and Limits are programmed.

DISENGAGING AND ENGAGING CARRIAGE

CHAIN OR BELT - TENSION ADJUSTMENT

WARNING

sObserve all safety warning and precautions!

sDisconnect power from opener and disconnect carriage in rail from bullet before beginning this task.

Visually inspect the chain or belt every 6 months.

NOTE: Tension adjustments should be made with the door in the down position and the carriage released.

sAt the center of the rail the chain or belt should not be resting on the rail. See adjustment illustration on right.

–With the bullet NOT engaged to the carriage, tighten adjustment nut until chain/belt does not, at the center of the rail, rest on rail. Do NOT overtighten.

sIs there rust on chain or frayed edges on belt?

–Contact a trained door system technician for chain/belt replacement.

sAre there kinks or twists in the chain or belt?

–Contact a trained door system technician for chain/belt replacement.

Tighten nut to increase tension on chain or belt

BELT

Belt

DOOR

Adjustment required

Belt

Correctly adjusted

Approx. 1/8"

TO ENGAGE, PULL

TO DISENGAGE, PULL

DOWN AND TOWARD

DOWN AND TOWARD

POWERHEAD. CHECK THE

DOOR. CHECK RED

RED BLOCK IS IN THE UP

BLOCK IN THE DOWN

POSITION. THEN LET GO.

POSITION. THEN LET GO.

REMOTE BATTERY REPLACEMENT

Belt at center of rail

CHAIN

Chain

Replace remote battery with a CR 2032 coin cell battery.

1. Open the remote case using a washer or coin that fits into the slot at the top of the remote

2. Replace battery.

3. Align components and

Adjustment required

Chain

Correctly adjusted

Approx. 1/8"

snap case closed.

Chain at center of rail

9

©2011 The Genie Company

9/2011

Page 9 Page 11
Image 10
Page 9 Page 11
Contents CHAIN/BELT This page Left Blank Safety Information Safety Features Opener FeaturesProgramming Overview Enters into and selects programming menusProgramming Limits Keep people clear of opening while door is movingFCC and IC Certified Default setting of Intellicode 2 must be changedRed = IntelliCode 1 / Green = IntelliCode Be programmed individually following steps belowOpen/Close Button Indicator LightWall Console Overview Independent Light Control ButtonSafe-T-Beam STB System Check Contact Reverse TestSee Door Balance Spring TensionRemote Battery Replacement Corrective Maintenance Change Light BulbsReset OPEN/CLOSE Travel Limit BeltDoors with very stiff weather seals Adjustment Guide Force SettingsAdjustment Guide Speed Settings Doors that start down, Stop and reverse before closingReference Circuit Wiring Diagram Power CordTroubleshooting Guide Operation Ss Program remote to powerhead. SeeFlashing OFFON/PURPLE OFF

1000 specifications

The Genie 1000 is a state-of-the-art aerial work platform designed to provide efficient aerial access solutions for various industrial and construction applications. Renowned for its robust build quality and advanced features, this unit combines functionality with ease of use, making it a favorite among professionals.

One of the standout features of the Genie 1000 is its compact design. With a narrow profile, it can easily navigate tight spaces and doorways, making it ideal for indoor and outdoor work environments. Its lightweight structure allows for easy transport between job sites, while still maintaining the strength and stability required for lifting tasks.

The Genie 1000 is equipped with an impressive maximum working height of 30 feet, allowing operators to reach elevated areas safely. Its platform capacity, which can accommodate up to 500 pounds, ensures that multiple workers and tools can be utilized simultaneously, enhancing productivity on the job. The unit also comes with a slide-out platform extension, granting additional reach when needed.

This aerial work platform employs advanced hydraulic technology, ensuring smooth and precise lifting and lowering operations. The Genie 1000 features a user-friendly control system that includes intuitive joystick controls, facilitating easy maneuverability. Safety is paramount, and this model is outfitted with various safety features, including an emergency stop button, guardrails, and a tilt alarm to prevent potential accidents during operation.

Another notable characteristic is its versatile power options. The Genie 1000 can be equipped with various power sources, including electric and diesel engines, depending on the operational requirements. This flexibility enables users to choose between an environmentally friendly electric model for indoor use and a robust diesel version for outdoor applications.

In terms of maintenance, the Genie 1000 is designed with serviceability in mind. Accessible components and clear maintenance points simplify routine checks and repairs, ensuring longevity and reliability.

Overall, the Genie 1000 stands out in the market for its exceptional performance, safety features, and ease of use. Its combination of compactness and capability makes it a vital tool in many industries, setting a new standard for aerial work platforms. Whether in construction, warehouse operations, or facility maintenance, the Genie 1000 is engineered to meet the demands of today’s workforce effectively.
Top Page Image Contents