Genie 1000 manual Adjustment Guide Force Settings, Adjustment Guide Speed Settings

ADJUSTMENT GUIDE - FORCE SETTINGS

CAUTION

Door closing force is FACTORY set and requires no adjustment for normal operation.

ssNever adjust the force settings to compensate for damage, including an unbalanced door, binding door track or broken spring.

ssPerform monthly CONTACT REVERSE TEST. See page 7.

Force settings are pre-programmed at the factory and "learned" during the Open/Close Limit settings steps.

For normal use, these settings should not need adjustment with this unit.

However, conditions possibly requiring adjustment are:

1.Doors with very stiff weather seals.

2.Doors that start down, STOP and reverse before closing.

3.Doors that start up, but STOP before they completely open.

FORCE ADJUSTMENT

ACTION LED INDICATION/RESULT

1Press & hold

both up and	RED	BLUE
down buttons
	OFF	OFF FLASHES 3 TIMES
2 seconds or until round	Then the Current UP FORCE
LED turns Red.
	SETTING will display. SEE CHART.

2Press either

	until you reach			USE CHART BELOW.
	desired setting.
3	Press &	PROGRAM		LOCKS IN SETTING.
				Then the Current
					OFF
	Release.			DOWN FORCE
					BLUE
			SET	SETTING will display.	FLASHING

4Press either

until you		USE CHART BELOW.
reach the				BLUE
desired setting.			BLUE
5	PROGRAM	LOCKS IN SETTING.
Press &		Both LEDs TURN
Release.
		BLUE then OFF	BLUE	OFF
	SET	confirms Force	BLUE	OFF
		Settings are reset.
	FORCE SETTINGS DONE
LED indicator colors		OFF Blue Purple		Red
Force Level		Powerhead LEDs
		LONG LED	ROUND LED
		Off		BLUE
		BLUE		Off
		BLUE		BLUE
		Off	PURPLE
		PURPLE		Off
		PURPLE	PURPLE
		Off		RED
		RED		Off
		RED		RED

ADJUSTMENT GUIDE - SPEED SETTINGS

Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit.

However, travel speed for the opener can be adjusted to a slower speed in both the open and close directions, To mimimize wear on heavier sectional doors.

NOTE: One-piece doors are automatically set to the slowest speed during Limits programming and cannot be adjusted.

There are 3 speed settings available for sectional doors. Please note that speed may be affected by door weight and balance, along with condition of door components and tracks.

SPEED ADJUSTMENT

	ACTION					LED INDICATION/RESULT
1	Press & Hold for	PROGRAM
	about 10 seconds
	or until both LEDs			SET				BLUE
	turn Blue.						BLUE
	Then release.
2 Press twice.
								BLUE
							BLUE
3 Press &		PROGRAM
	Release.						FLASHES BLUE 3 TIMES
			SET			OFF
						Then the Current Speed setting
						for OPENING travel will display.
						SEE CHART BELOW.
4 Press either until						NOTE: Depending on the criteria
	you reach the					mentioned above, you may not
	desired setting.					have the option to increase speed.
5	Press &	PROGRAM				LOCKS IN OPENING SETTING.
	Release.							OFF
			SET
						FLASHES
						BLUE 3 TIMES
						Then the Current Speed setting
						for CLOSING travel will display.
						SEE CHART BELOW.
6 Press either until						NOTE: Depending on the criteria
	you reach the					mentioned above, you may not
	desired setting.					have the option to increase speed.
7	Press &	PROGRAM				LOCKS IN CLOSING SETTING.
	Release.							FLASH BLUE
	Both LEDs FLASH		SET			FLASH BLUE
	BLUE to confirm setting.
	FORCE SETTINGS DONE
LED indicator colors					OFF Blue Purple				Red
Speed Level						Powerhead LEDs
						LONG LED		ROUND LED
High						RED			RED
Medium						PURPLE			PURPLE
Low						BLUE			BLUE

9/2011 ©2011 The Genie Company 10