Genie 3563435770, 2040L Opener does not Operate, Does from the Remote, With the Wall Control

Page 15

Trouble 7:

THE DOOR STARTS TO CLOSE BUT

 

REVERSES BEFORE FULLY CLOSING

 

AIf the opener light flashes 4 times, the close door force setting may be too low.

BThe door hardware may be binding causing the door force setting to be exceeded. Disengage the carriage and manually check the door movement and balance. Lubricate the door hardware as recommended by the manufacturer.

CThe Safe-T-Beam® has been interrupted while the door is closing (opener light flashes 3 times), or the Safe-T-Beam® is out of alignment.

Trouble 8: OPENER LIGHTS STAY ON

AIt is normal for the lights to stay on for about 5 minutes after being activated.

BIf the lights were turned on using the light button on the wall control, they will stay on until they are turned off using the wall control light button or the door is cycled open or shut.

Trouble 9:

OPENER DOES NOT OPERATE

 

FROM THE WALL CONTROL, BUT

 

 

DOES FROM THE REMOTE

ACheck the wall control wiring at the wall control and opener terminals.

BCheck the wiring between the wall control and the opener. Look for any staples that have cut into the wire’s insulation or wire that has been pinched. If the opener light flashes 2 times when the remote is used, the wall control wires are shorted and the bad section must be replaced.

Trouble 10: OPENER DOES NOT OPERATE FROM THE REMOTE, BUT DOES

WITH THE WALL CONTROL

ABe sure that the remote is programmed into the opener.

BCheck the remote’s battery. The red light should light up when ever the remote button is pressed.

Trouble 11: OPENER CLOSES, BUT DOES NOT OPEN WITH THE REMOTE

AIf the opener lights flash 5 times when the remote is activated, and the door does not open, the vacation switch is on. Turn the vacation switch off

(optional accessory).

Trouble 12: REMOTE CONTROL WILL NOT OPERATE AT A DISTANCE FROM

THE OPENER.

ABe sure that the opener’s antenna (the short white wire on the back of the opener) is extended upward from the opener.

BCheck the remote’s battery.

CRemote control operating distance will vary depending on the amount of interference and metal obstacles in the path of the signal.

Trouble 13: OPENER RUNS BY ITSELF

AExamine all remotes programmed into the opener. Check for items that might be pressing on a remote button. Look for remotes stuffed between seat cushions of the car.

BIf a remote has been lost or stolen, erase the opener’s memory to prevent the missing remote from activating the opener. Reprogram the remaining remotes into the opener.

CCheck the wiring between the wall control and the opener. Look for staples that have cut into the wire’s insulation, or wire that has been pinched by a object. Replace any bad wire.

DExamine the wiring at the opener’s terminals and the wall control terminals. Look for any wires that are close to or touching adjacent terminals.

Trouble 14: OPENER IS NOISY

ALubricate the door hardware as recommended by the garage door manufacturer.

Trouble 15:

THE OPENER WILL NOT OPERATE

`

BECAUSE OF A POWER FAILURE

 

APull the carriage release handle to disengage the opener from the door. The door can be operated manually until power is restored.

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents AC Powered Belt Drive Ever be required With this manual for future reference should serviceForce Guard Control Safe-T-Beam STB Non-Contact Reversing SystemSafe-T-Reverse Contact Reversing System Safe-T-Stop Timed Reversed SystemThickness PRE-INSTALLATION ChecklistCheck Check Garage Door Check following items before assembling OpenerSectional Door Check Check Power HeadCheck Check Door Header Area Mounting AreaCheck Emove Xisting Arage Door Locks Permanent wiring must be installed by a LicensedCheck Check SAFE-T-BEAM Check Recommended ToolsAligning the SAFETY-T-BEAMS Maintenance and AdjustmentsPlace AN Object BEAM’S Path Programming Remote ControlsProgram each additional Remote using step a above Block the Beam While the Bullet Is Moving DownSnap the back of the transmitter on FlashlightErasing all remotes Figure Program receiver again as neededProgramming your car’s HomeLink system Adjusting the Open and Close LimitsAdjust the open limit a Remote does not have adequate rangeLimits Adjusting the Open and CloseAdjusting and Testing the Force Controls Adjust the close limit BWithout reversing Adjusting and Testing the ForceTest the Safety Reverse ControlsDisengaging the Door from the Opener Periodic Maintenance ScheduleTrouble TroubleshootingOpener Opener does not OperateDoes from the Remote With the Wall ControlPower Head System Status Problem Cause RemedyParts Identification

2040L, 3563435770 specifications

The Genie 3563435770,2040L is a versatile, high-performance lift designed to meet the ever-evolving needs of construction, maintenance, and industrial applications. Engineered for efficiency and safety, this model stands out for its impressive specifications and innovative technologies.

One of the key features of the Genie 3563435770,2040L is its robust lifting capability. With a maximum working height of 40 feet, the lift allows operators to reach elevated workspaces with ease. The platform capacity is designed to support multiple workers and their tools, ensuring that tasks can be completed efficiently without compromising safety.

The lift incorporates Genie’s advanced hydraulic system, which provides smooth and responsive elevation. This enhances productivity on the job site while minimizing downtime. The system is also designed for energy efficiency, reducing the overall operational costs associated with lifting tasks.

In terms of mobility, the Genie 3563435770,2040L is equipped with all-terrain tires and a compact design, allowing it to navigate difficult terrains and fit into tight spaces. Operators can easily maneuver the lift on job sites, making it ideal for both indoor and outdoor applications. Additionally, the lift features a 360-degree rotating turntable, providing enhanced flexibility and reaching angles that are often challenging with traditional lifts.

Safety is paramount in the design of the Genie 3563435770,2040L. The model is equipped with numerous safety features, including automatic braking systems, anti-slip surfaces on the platform, and guardrails to ensure secure operation at heights. Emergency descent systems are also integrated, providing peace of mind for operators in case of malfunction.

The Genie 3563435770,2040L incorporates smart technology, such as an onboard diagnostics system that allows operators to monitor performance and conduct maintenance checks easily. This predictive maintenance capability minimizes downtime and prolongs the lifecycle of the equipment.

Furthermore, the lift's user-friendly controls make it accessible for operators of all experience levels. Training programs and operator manuals are readily available to facilitate smooth and safe operation.

In conclusion, the Genie 3563435770,2040L is an exceptional lift that combines power, efficiency, and safety. Its cutting-edge technologies and practical features make it a reliable solution for a wide range of lifting needs in various sectors.
Top Page Image Contents