Genie 2040L, 3563435770 Check Check SAFE-T-BEAM, Permanent wiring must be installed by a Licensed

Page 6

Check Step 6: CHECK CEILING FOR GROUNDED POWER SOURCE

ACheck that there is a 15 Amp 120 Volt grounded electrical outlet or grounded permanent wiring box (per building code) within 3' of Opener Power Head:

•If not, an outlet or wiring box must be installed. Contact a licensed electrician for installation.

•If building codes require permanent wiring, Power Head must be partially disassembled to install appropriate wiring in place of Power Cord. See Assembly and Information Poster.

NOTE

Permanent wiring must be installed by a Licensed

Electrician. Not all Genie Factory Authorized Dealers are Licensed Electrician's. Contact someone who is a Licensed Electrician.

WARNING

Do Not use an extension cord! Extension cords can cause dangerous overheating conditions.

Do Not use portable generator! This product is designed to operate using standard house current. Do Not use alternate power supplies,

Check Step 7: CHECK SAFE-T-BEAM®

MOUNTING BRACKET LOCATION

Check for wood garage frame, jamb, or masonry at mounting location (6" above floor) with attachment tabs facing away from garage door (Figure 7).

AIf you cannot mount Safe-T-Beam® Mounting Bracket to wood frame:

•Concrete screws and concrete anchors (not included) must be used to mount Brackets on masonry with attachment tabs facing away from garage door.

Source

Sensor

Safe-T-Beam®

Mounting Bracket

Top of

Bracket 6"

above

floor

Figure 7 Mounting Safe-T-Beam® Components

Check Step 8: RECOMMENDED TOOLS

ATools (Figure 8):

BAdditional tools to make installation easier:

•Slotted and phillips screw-driver bits

•Stud finder

•Sheet-metal cutting snips

D R E G

Check Step 9: EMOVE XISTING ARAGE DOOR LOCKS

Check that the garage door locks, rope, and T-Handles are removed from the garage door before starting the installation.

AIf your garage does not have a separate entry door, it is highly recommended to install a Genie Emergency Release Kit (GER-2). Emergency Release Kit lets you open the garage door from outside if there is a power failure. (Please see Accessories Order Form on page 23.)

Before going further, get any items and tools needed for

❐Garage door frame reinforcement brackets, screws, bracing or reinforcement kits (dealer)

❐Lag Screws (1-1/4") for a wood door less than 2" thick (store)

❐Electrical outlet and/or wiring (supplied by a licensed electrician)

❐Sufficient angle iron or strapping for hanging Power Head (store)

❐100 Watt light bulb (Rough service bulbs recommended)(store)

❐GER-2 Emergency Release Kit for entry during power failure (store)

❐Wood for header, ceiling, and/or door bracing reinforcement (if needed)

❐Masonry fasteners for Safe-T-Beam® Bracket installation, (if needed)

❐Masonry drill bit (if needed)

❐Extension Kit (for 8’ Garage Doors)your installation

Go to Assembly and Installation Poster for full Installation Instructions.

Figure 8 Recommended Tools

6

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Page 5 Page 7
Image 6
Page 5 Page 7
Contents AC Powered Belt Drive With this manual for future reference should service Ever be requiredSafe-T-Stop Timed Reversed System Safe-T-Beam STB Non-Contact Reversing SystemSafe-T-Reverse Contact Reversing System Force Guard ControlCheck following items before assembling Opener PRE-INSTALLATION ChecklistCheck Check Garage Door ThicknessMounting Area Check Check Power HeadCheck Check Door Header Area Sectional DoorCheck Recommended Tools Permanent wiring must be installed by a LicensedCheck Check SAFE-T-BEAM Check Emove Xisting Arage Door LocksMaintenance and Adjustments Aligning the SAFETY-T-BEAMSBlock the Beam While the Bullet Is Moving Down Programming Remote ControlsProgram each additional Remote using step a above Place AN Object BEAM’S PathProgram receiver again as needed FlashlightErasing all remotes Figure Snap the back of the transmitter onRemote does not have adequate range Adjusting the Open and Close LimitsAdjust the open limit a Programming your car’s HomeLink systemAdjust the close limit B Adjusting the Open and CloseAdjusting and Testing the Force Controls LimitsControls Adjusting and Testing the ForceTest the Safety Reverse Without reversingPeriodic Maintenance Schedule Disengaging the Door from the OpenerTroubleshooting TroubleWith the Wall Control Opener does not OperateDoes from the Remote OpenerPower Head System Status Problem Cause RemedyParts Identification

2040L, 3563435770 specifications

The Genie 3563435770,2040L is a versatile, high-performance lift designed to meet the ever-evolving needs of construction, maintenance, and industrial applications. Engineered for efficiency and safety, this model stands out for its impressive specifications and innovative technologies.

One of the key features of the Genie 3563435770,2040L is its robust lifting capability. With a maximum working height of 40 feet, the lift allows operators to reach elevated workspaces with ease. The platform capacity is designed to support multiple workers and their tools, ensuring that tasks can be completed efficiently without compromising safety.

The lift incorporates Genie’s advanced hydraulic system, which provides smooth and responsive elevation. This enhances productivity on the job site while minimizing downtime. The system is also designed for energy efficiency, reducing the overall operational costs associated with lifting tasks.

In terms of mobility, the Genie 3563435770,2040L is equipped with all-terrain tires and a compact design, allowing it to navigate difficult terrains and fit into tight spaces. Operators can easily maneuver the lift on job sites, making it ideal for both indoor and outdoor applications. Additionally, the lift features a 360-degree rotating turntable, providing enhanced flexibility and reaching angles that are often challenging with traditional lifts.

Safety is paramount in the design of the Genie 3563435770,2040L. The model is equipped with numerous safety features, including automatic braking systems, anti-slip surfaces on the platform, and guardrails to ensure secure operation at heights. Emergency descent systems are also integrated, providing peace of mind for operators in case of malfunction.

The Genie 3563435770,2040L incorporates smart technology, such as an onboard diagnostics system that allows operators to monitor performance and conduct maintenance checks easily. This predictive maintenance capability minimizes downtime and prolongs the lifecycle of the equipment.

Furthermore, the lift's user-friendly controls make it accessible for operators of all experience levels. Training programs and operator manuals are readily available to facilitate smooth and safe operation.

In conclusion, the Genie 3563435770,2040L is an exceptional lift that combines power, efficiency, and safety. Its cutting-edge technologies and practical features make it a reliable solution for a wide range of lifting needs in various sectors.
Top Page Image Contents