Chamberlain 1145jg, 1160, 80ad, 1150 Programming, To Code a Hand-held Remote Control Transmitter

Page 31

PROGRAMMING

Below are instructions for programming your opener to operate with remote control transmitters.

To Code a Hand-held Remote

Control Transmitter

USING THE “SMART” BUTTON

1. Press and hold the button on the

 

hand-held remote* that you wish

er

 

Lift

 

Mast

to operate your garage door.

 

2.Press and release the “Learn” button on the back panel of the opener.

3.The light bulb will blink when the code has been accepted. If light bulb is not installed, two clicks will be heard.

To Erase All Codes From Opener

Receiver Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “Learn” button on opener until the smart indicator light goes out (approximately 6 seconds). All previous codes are now erased.

Reprogram each remote or keyless entry you wish to use.

*Multi-Function Remotes

If provided with your

garage door opener, the large button is

factory programmed to

operate it. Additional buttons on any multi- function remote or

mini-remote can be programmed to operate other garage door openers.

SPECIFICATIONS

Horsepower

1/2

Rated Pull Force

800N

Stand-by power rating

 

@ 230V

5.5W

 

Motor

Type

Permanent split capacitor

Speed

1500 rpm

Volts

230-240 Volts AC-50Hz Only

Current

2.0 amperes

 

Drive Mechanism

Gears

16:1 worm gear reduction

Drive

Chain with one-piece trolley on

 

steel C-rail.

Length of Travel

Adjustable to 2.29m (7-1/2 feet)

Travel Rate

127mm (5") per second

Lamp

On when door starts, off 2-1/2

 

minutes after stop.

Door Linkage

Adjustable door arm. Pull cord

 

trolley release.

 

Safety

Personal

Push button and stop. Push button

 

and automatic reversal in down

 

direction. Push button and automatic

 

stop in up direction.

Electronic

Independent up and down force

 

adjustment screws.

Electrical

Motor overload protector and low

 

voltage push button wiring.

Limit Device

Circuit actuated by limit nut.

Limit Adjustment

Screwdriver adjustment on side panel.

Start Circuit

Low voltage push button circuit.

 

Dimensions

Length (Overall)

3.1m (122-1/2")

Headroom Required

5cm (2")

Hanging Weight

14.5 kg (32 lb)

 

Receiver

Operating Frequency

433.92MHz

Computer Codes

8

Code Switch Code

1

Keypad Code

1

114A2845

31

Image 31
Contents With 433MHz Radio Controls Introduction Table of ContentsSectional Door Testing Your DoorPreparing your garage door Tools neededPlanning Sectional Door InstallationsOpener ARM Mounting Location ONE-PIECE Door Installations OFF Centre Installation of OpenerOne-Piece Door with Track One-Piece Door without Track Carton Inventory Hardware Inventory InstallationInsert Chain into Rail & Assemble Header Sleeve Assembly StepInstall the Chain Assemble the RailSet Chain Tension Fasten Rail to Opener & Install ChainAttach Trolley to Rail Attach Chain SpreaderInstall Chain Noise Reduction Pads optional Installation Important Installation InstructionsProceed to , Installation StepDetermine the Header Bracket Location Sectional Door ONE-PIECE Door with TrackOne-piece door without track pivot hardware ONE-PIECE Door Without TrackExample One-piece door without track jamb hardwareWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Position the Opener Attach the Rail to the Header BracketSectional Door or ONE-PIECE Door with Track Hang the Opener Remote Control Wall Mount optional Install the door controlSafety Infrared Reversing Sensor Model Wiring Instructions for AccessoriesInstall the Light KEY Switch ModelAttach the Emergency Release Rope and Handle Connect Electric PowerImportant Information about Safety Reversing Sensors Install the Safety Infrared Reversing Sensors OptionalFacing the door from inside the garage Wood Doors Metal, insulated or light weight factory reinforced doorsFasten the Door Bracket Sectional DoorsNot Provided ONE-PIECE DoorsSectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment Procedures for One-Piece DoorsALL ONE-PIECE Doors Assemble the Door ArmLimit Adjustment Adjustment StepAdjust the Force Important Safety Check Test the Safety Reverse SystemTest the Safety Infrared Reversing Sensors if installed AdjustActivate your opener with any of the following Using Your Garage Door OpenerWhen the opener is activated OperationTwice a Year To Open the Door ManuallyCare of Your Opener Once a MonthOpener doesnt operate from either door control or remote TroubleshootingMulti-Function Remotes To Code a Hand-held Remote Control TransmitterProgramming To Erase All Codes From Opener Receiver MemoryWarranty

1155, 1156, 1140, 1150, 80ad specifications

The Chamberlain 1160JG, 1160, 1146, 120AD, and 1145 garage door openers are some of the most reliable and feature-rich options available in today’s market. These models are renowned for their robust performance, user-friendly interface, and advanced technology, making them a top choice for homeowners seeking convenience and security.

The Chamberlain 1160JG and 1160 models stand out with their powerful DC motor, which ensures a smooth and quiet operation. They are designed for faster opening speeds, allowing users to enter and exit the garage quickly. One of the prominent features of these models is the built-in myQ technology, which enables remote access and control via smartphone applications. Users can monitor their garage door status, receive alerts, and operate the door from virtually anywhere, enhancing convenience and peace of mind.

The Chamberlain 1146 model combines strength and reliability, equipped with a durable chain drive system. This model offers exceptional lifting power, making it suitable for heavy garage doors. The 1146 also includes a battery backup system, ensuring functionality even during power outages. Its safety features, including infrared sensors, help prevent accidents by detecting obstructions in the door's path.

The Chamberlain 120AD model is particularly appreciated for its easy installation process. This model features a belt drive system, which provides quieter operation compared to chain-driven alternatives. This makes the 120AD an excellent choice for homes with living spaces adjacent to the garage. It also includes built-in Wi-Fi, enabling smart home integration and remote access through the myQ app.

The Chamberlain 1145 model is a compact yet powerful option that maintains high reliability. It offers a strong chain drive system and a variety of safety features, including rolling code technology that enhances security by changing the access code after every use. The 1145 is ideal for families looking for a cost-effective yet dependable solution.

Overall, the Chamberlain 1160JG, 1160, 1146, 120AD, and 1145 garage door openers not only bring convenience through advanced technology but also prioritize safety, making them an excellent investment for any homeowner. Their blend of performance, durability, and smart technology ensures that users benefit from a hassle-free garage door experience.