Chamberlain 80ad, 1160, 1150 Installation Step, Determine the Header Bracket Location, Proceed to

Page 12

INSTALLATION STEP 1

Determine the Header Bracket Location

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

WARNING

To prevent possible SERIOUS INJURY or DEATH:

Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall.

Concrete anchors MUST be used if mounting header bracket or 40mm reinforcement board into masonry.

NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, all of which are under EXTREME tension.

ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might not reverse when required.

SECTIONAL DOOR

AND ONE-PIECE DOOR WITH TRACK

1.Close the door and mark the inside vertical centreline of the garage door.

2.Extend the line onto the header wall above the door.

NOTE: You can fasten the header bracket within 300mm of the left or right of the door center only if a torsion spring or centre bearing plate is in the way; or you can attach it to the ceiling (see page 14) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 12mm.)

If you need to install the header bracket on a 40mm reinforcement board (on wall or ceiling), use lag screws (not provided) to securely fasten the 40mm reinforcement board to structural supports as shown here and on page 13. If installing into masonry, use concrete anchors.

3.Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 50mm above the high point. This height will provide travel clearance for the top edge of the door.

Proceed to Step 2, page 14.

 

 

 

Finished

 

Vertical

 

Ceiling

 

40mm

 

 

Centreline

 

 

Reinforcement

Header

 

 

Board

Structural

Wall

 

 

 

 

 

 

Supports

Vertical

Centreline

Ceiling

 

 

Header Wall

 

 

50mm

Track

 

Highest Point

Sectional door

of Travel

 

with curved

 

track

 

Door

 

 

 

Header Wall

Track

 

50mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Highest Point

One-piece

Door

 

 

 

 

 

of Travel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

door with

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

horizontal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

track

 

 

 

 

 

 

 

 

 

 

 

114A2845

12

Image 12
Contents With 433MHz Radio Controls Table of Contents IntroductionTesting Your Door Preparing your garage doorTools needed Sectional DoorSectional Door Installations PlanningOpener ARM Mounting Location OFF Centre Installation of Opener ONE-PIECE Door InstallationsOne-Piece Door with Track One-Piece Door without Track Carton Inventory Installation Hardware InventoryAssembly Step Install the ChainAssemble the Rail Insert Chain into Rail & Assemble Header SleeveFasten Rail to Opener & Install Chain Attach Trolley to RailAttach Chain Spreader Set Chain TensionInstall Chain Noise Reduction Pads optional Important Installation Instructions InstallationInstallation Step Determine the Header Bracket LocationSectional Door ONE-PIECE Door with Track Proceed to ,ONE-PIECE Door Without Track ExampleOne-piece door without track jamb hardware One-piece door without track pivot hardwareInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Position the OpenerSectional Door or ONE-PIECE Door with Track Hang the Opener Install the door control Remote Control Wall Mount optionalWiring Instructions for Accessories Install the LightKEY Switch Model Safety Infrared Reversing Sensor ModelConnect Electric Power Attach the Emergency Release Rope and HandleInstall the Safety Infrared Reversing Sensors Optional Important Information about Safety Reversing SensorsFacing the door from inside the garage Metal, insulated or light weight factory reinforced doors Fasten the Door BracketSectional Doors Wood DoorsONE-PIECE Doors Not ProvidedConnect Door Arm to Trolley Sectional Doors onlyAdjustment Procedures for One-Piece Doors ALL ONE-PIECE DoorsAssemble the Door Arm Connect the door arm to the trolleyAdjustment Step Limit AdjustmentAdjust the Force Test the Safety Reverse System Test the Safety Infrared Reversing Sensors if installedAdjust Important Safety CheckUsing Your Garage Door Opener When the opener is activatedOperation Activate your opener with any of the followingTo Open the Door Manually Care of Your OpenerOnce a Month Twice a YearTroubleshooting Opener doesnt operate from either door control or remoteTo Code a Hand-held Remote Control Transmitter ProgrammingTo Erase All Codes From Opener Receiver Memory Multi-Function RemotesWarranty

1155, 1156, 1140, 1150, 80ad specifications

The Chamberlain 1160JG, 1160, 1146, 120AD, and 1145 garage door openers are some of the most reliable and feature-rich options available in today’s market. These models are renowned for their robust performance, user-friendly interface, and advanced technology, making them a top choice for homeowners seeking convenience and security.

The Chamberlain 1160JG and 1160 models stand out with their powerful DC motor, which ensures a smooth and quiet operation. They are designed for faster opening speeds, allowing users to enter and exit the garage quickly. One of the prominent features of these models is the built-in myQ technology, which enables remote access and control via smartphone applications. Users can monitor their garage door status, receive alerts, and operate the door from virtually anywhere, enhancing convenience and peace of mind.

The Chamberlain 1146 model combines strength and reliability, equipped with a durable chain drive system. This model offers exceptional lifting power, making it suitable for heavy garage doors. The 1146 also includes a battery backup system, ensuring functionality even during power outages. Its safety features, including infrared sensors, help prevent accidents by detecting obstructions in the door's path.

The Chamberlain 120AD model is particularly appreciated for its easy installation process. This model features a belt drive system, which provides quieter operation compared to chain-driven alternatives. This makes the 120AD an excellent choice for homes with living spaces adjacent to the garage. It also includes built-in Wi-Fi, enabling smart home integration and remote access through the myQ app.

The Chamberlain 1145 model is a compact yet powerful option that maintains high reliability. It offers a strong chain drive system and a variety of safety features, including rolling code technology that enhances security by changing the access code after every use. The 1145 is ideal for families looking for a cost-effective yet dependable solution.

Overall, the Chamberlain 1160JG, 1160, 1146, 120AD, and 1145 garage door openers not only bring convenience through advanced technology but also prioritize safety, making them an excellent investment for any homeowner. Their blend of performance, durability, and smart technology ensures that users benefit from a hassle-free garage door experience.