Harbor Freight Tools 68328 manual Pre-Start Checks, Operation, Checking and Filling Fuel

Page 10

Operation

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before

set up or use of this product.

Pre-Start Checks

Inspect Pump and engine, looking for damaged, loose, and/ or missing parts before set up and starting. If any problems are found, do not use equipment until fixed properly.

Prime the Pump

Checking and Filling Engine Oil

CAUTION! Your Warranty is VOID if the engine’s crankcase is not properly filled with oil before each use. Before each use, check the oil level. Do not run the engine with low or no engine oil. Running the engine with no or low engine oil WILL permanently damage the engine.

1.Make sure the engine is stopped and is level.

2.Close the Fuel Valve.

3.Clean the top of the Dipstick and the area around it. Remove the Dipstick by threading it counterclockwise, and wipe it off with a clean lint free rag.

Before starting the engine, fill the Pump with water. To do this:

Full level

Full level

1.Unthread the Priming Water Filler Cap by turning it counterclockwise.

Priming Water

Filler Cap

2.Fill the unit with clean water up to the top of the opening. Replace the Priming Water Filler Cap and tighten securely.

IMPORTANT! Always check for water in the Pump Housing before each use. Never attempt to run the Water Pump without the Pump Housing FULL of water. Running the Water Pump without water for an extended period of time will damage the Water Pump and void the Warranty.

4.Reinsert the Dipstick without threading it in and remove it to check the oil level. The oil level should be up to the full level as shown above.

5.If the oil level is at or below the low mark add the appropriate type of oil until the oil level is at the proper level. SAE 10W‑30 oil is recommended for general use. (The SAE Viscosity Grade chart on page 12 in the Service section shows other viscosities to use in different average temperatures.)

6.Thread the dipstick back in clockwise.

CAUTION! Do not run the engine with too little oil. The engine will be permanently damaged.

Checking and Filling Fuel

WARNING! To prevent serious injury from fire:

Fill the fuel tank in a well-ventilated area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it to cool before adding fuel. Do not smoke.

1.Clean the Fuel Cap and the area around it.

2.Unscrew and remove the Fuel Cap.

3.If needed, fill the Fuel Tank to the top of the Fuel Level marker on the fuel filter with 87 octane or higher unleaded gasoline.

Note: Do not use gasoline containing more than 10% ethanol (E10). Do not use E85 ethanol.

Note: Do not use gasoline that has been stored in a metal fuel container or a dirty fuel container. It can cause particles to enter the carburetor, affecting engine performance and/or causing damage.

4.Then replace the Fuel Cap.

5.Wipe up any spilled fuel and allow excess to evaporate before starting engine. To prevent FIRE, do not start the engine while the smell of fuel hangs in the air.

Page 8

For Pump technical questions, please call 1-800-444-3353.

Item 68328

 

For Engine technical questions, please call 1-800-520-0882.

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 2Gasoline Powered Clear Water Pump Using an engine indoors can Kill YOUSpecifications PumpSafety Warnings Symbol DefinitionsSet up Precautions Symbol Property or StatementEngine Precautions Operating Precautions Carbon Monoxide Hazard Using an engine indoors can KillService Precautions RefuelingControls Set up Connecting HosesDischarge Port Locating the Water Pump Operation ConcernsPrime the Pump Checking and Filling Engine Oil Pre-Start ChecksOperation Checking and Filling FuelTurn the Engine Switch on Starting the EngineStopping the Engine Break-in PeriodMaintenance and Service Maintenance ProceduresCleaning, Maintenance, and Lubrication Schedule Hr. of useCleaning Air Filter Element MaintenanceEngine Oil Change Recommended Spark Plug Spark Plug Maintenance CapBrand Storage Pump Troubleshooting Problem Possible Causes Likely SolutionsDo not use gasoline with more than Engine TroubleshootingProblem Possible Causes Probable Solutions 10% ethanol E15, E20, E85, etcUse Engine will not start Compression Related sectionParts List Including Item 68124 99cc engine Part Description QtyFor Engine For Pump Technical questions, please Parts Diagram Including Item 68124 99cc engineCall 1-800-444-3353. call Manufacturer’s Warranty Coverage Emission Control System WarrantyUnited States Emission Control Defects Warranty Statement WarrantiesCoverage Exclusions Service and MaintenanceConsequential Damages Coverage Warranted PartsMission Oaks Blvd. PO Box 6009 Camarillo, CA

68328 specifications

Harbor Freight Tools has established itself as a reliable source for high-quality yet affordable tools and equipment, appealing to both casual DIY enthusiasts and professional tradespeople. One such product that has garnered attention is the Harbor Freight Tools 68328, a compact and efficient tool that embodies the spirit of innovation and practicality.

The Harbor Freight Tools 68328 is primarily known for its portability and ease of use, making it an ideal option for those who require a dependable tool on the go. This model stands out with its robust structural design and lightweight framework, allowing users to handle it effortlessly without compromising on performance. Its size makes it suitable for tight spaces, enabling access to areas that might be challenging for larger tools.

One of the standout features of the Harbor Freight 68328 is its advanced motor technology, which delivers consistent power and torque. This capability ensures that users can tackle a variety of tasks, from basic home repairs to more complex projects, more efficiently. Additionally, the tool is designed with user comfort in mind. The ergonomic handle provides a secure grip, reducing the risk of slippage and fatigue during extended use.

The 68328 also showcases an impressive array of functionalities that cater to different working conditions. With multiple speed settings, users can adjust the tool's performance based on the specific demands of their project. This versatility is especially beneficial when transitioning between different materials or tasks, optimizing efficiency and effectiveness.

Durability is another hallmark of the Harbor Freight 68328. Constructed from high-quality materials, it is built to withstand rigorous use while maintaining its functionality over time. This durability is complemented by a user-friendly maintenance design, which allows for easy servicing and upkeep, ensuring long-term reliability.

Moreover, safety features such as automatic shut-off and overload protection add an extra layer of reassurance for users, allowing them to focus on their work without constant concern for potential hazards.

In summary, the Harbor Freight Tools 68328 is a standout product that combines portability, efficiency, and durability, making it a valuable addition to any toolbox. Its advanced motor technology, versatile features, and thoughtful design principles work in concert to provide users with a reliable and effective tool tailored to meet a wide range of needs. Whether for professional use or home improvement projects, the 68328 serves as a testament to Harbor Freight’s commitment to quality and affordability in the tool industry.
Top Page Image Contents