Nilfisk-Advance America 56315042(755), 56315044(855) English / B-15, WET Scrubbing, WET Vacuuming

Page 37

ENGLISH / B-15

WET SCRUBBING

WARNING!

Be sure you understand the operator controls and their functions. While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills. Clean only while ascending (driving up) the ramp.

1Follow the instructions in the Preparing The Machine For Use section of this manual.

2Turn the Master Key Switch (A) ON (I). This will display the control panel indicator lights, reference the Battery Indicator and Hour Meter on the Display (D or J).

3To transport the machine to the work area, push the Drive Paddle (34) forward to go forward or pull the Drive Paddle (34) backward to move the machine in reverse. Vary the pressure on the Drive Paddle (34) to obtain the desired speed.

NOTE: Speed Control Knob (35) is used to control the maximum speed in either forward or reverse.

4Press and hold the Solution Switch (B) for 5 seconds to pre-wet the floor. NOTE: This must be done prior to pressing the Scrub ON Switch (I).

5Press the Scrub ON Switch (I) once for Regular Scrub or twice for Heavy Scrub mode. Hold this switch for 5 seconds for Extreme Scrub mode. Both the solution system and detergent (EDS models) system have 3 flow rate presets that coincide with the 3 scrub modes (see Control Panel). NOTE: There is a solution flow rate over ride function if you wish to increase solution flow without increasing scrub pressure. Hold the Solution Switch (B) for 3 seconds (solution indicator will start flashing) and then let go. You then have 3 seconds to set a different flow rate by simply pressing the Solution Switch (B) repeatedly until the Solution Flow Rate Indicator (D1) shows the rate you desire (Regular, Heavy or Extreme / see Control Panel). Any subsequent scrub pressure adjustments will reset the solution flow rate to default.

NOTE: The solution, vacuum and detergent (EDS models) systems are automatically activated when the Scrub ON Switch (I) is pressed. No further action is required other than lowering the squeegee (17). Any individual system can be turned OFF or back ON by simply pressing its switch at any time during scrubbing. If you have installed the Extended Scrub Kit, it will not be automatically activated. You must press the Recycle Switch (G) to activate this system. The recycle system will not turn ON until the water level in the recovery tank reaches a certain level.

6Lower the squeegee with the Squeegee Raise / Lower Lever (17).

7When the Drive Paddle (34) is in the neutral position, the scrub, vacuum, solution and detergent (EDS models) systems are activated but not running. Grip the Operator Control Handle (2) and push the Drive Paddle (34) forward to start the scrub, vacuum, solution and detergent (EDS models), and to move the machine forward. For best results, move the machine at a slow walking speed. Press the Solution Switch (B) once to turn OFF while making sharp turns. Pull the Drive Paddle (34) backward to move the machine in reverse. The brushes will run while moving the machine in reverse, but solution and chemical will not be dispensed.

CAUTION!

To avoid damaging the floor, keep the machine moving while the brushes are turning.

8For extremely dirty floors, a one-pass scrubbing operation may not be satisfactory and a “double-scrub” operation may be required. This operation is the same as a one-pass scrubbing except on the first pass the squeegee is in the up position. This allows the cleaning solution to remain on the floor to work longer. The final pass is made over the same area, with the squeegee lowered to pick up the accumulated solution.

9The recovery tank has an automatic shut-off switch that turns ALL systems OFF except the drive system when the recovery tank is full. When this switch is activated, the recovery tank must be emptied. The machine will not pick up water or scrub with the switch activated.

NOTE: All other indicators vanish and a “Recovery Tank FULL” Indicator (D7) turns on in the Display Panel when the switch is activated on “EDS” models. The Hour Meter (J2) momentarily flashes each letter of the word FULL over and over on “Standard” models.

10When the operator wants to stop scrubbing or the recovery tank is full, press the Scrub OFF Switch (H) once. This will automatically stop the scrub brushes and solution flow and the scrub deck will raise UP. NOTE: The vacuum will stop after a 10 second delay. This is to allow any remaining water to be picked up without turning the vacuum back on.

11Raise the squeegee and drive the machine to a designated wastewater “DISPOSAL SITE” and empty the recovery tank. To empty, pull the Recovery Tank

Drain Hose (27) from its hanger and open the cap (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled flow of waste water). The Recovery Tank Drain Hose (27) can be squeezed to regulate the flow. Refill the solution tank and continue scrubbing.

NOTE: Make sure the Recovery Tank Cover (5) and the Recovery Tank Drain Hose (27) cap is properly seated or the machine will not pick-up water correctly. When the batteries require recharging the Battery LOW Indicator (D8) will come on (EDS models) or the Battery Indicator (J1) will flash red (Standard models) and the vacuum motor will shut off after 30 seconds. Transport the machine to a service area and recharge the batteries according to the instructions in the Battery section of this manual.

WET VACUUMING

Fit the machine with optional attachments for wet vacuuming.

1Disconnect the Recovery Hose (19) from the Squeegee (13).

2Attach suitable wet pick-up tools to the hose (Available from Nilfisk).

3Turn the Master Key Switch (A) ON.

4Press the Wand Switch (E) once to turn ON the vacuum motor.

SERVICE NOTE: Refer to the service manual for detailed functional descriptions of all controls and optional programmability.

FORM NO. - 56041684 - BA 755, BA 855 - B-15

Image 37
Contents BA 755, BA İçİndekİler TürkçeGİrİş Türkçe / A-3Parçalar VE Servİs KünyeTehlİke Makİnenİzİ Taniyin Türkçe / A-5Türkçe Kontrol Panelİ EDS Türkçe / A-7Kontrol PANELİ- Standart Aküler Türkçe / A-9Şekil Aküler servise alındığındaFirçalarin Monte Edİlmesİ Dİsk Sİstemİ 10 / TürkçeFirçalarin Montaji Sİlİndİrİk Sİstem Solüsyon Tankinin Doldurulmasi 12 / TürkçeToplayicinin Montaji EDS Deterjan Sİstemİnİn Hazirlanmasi VE Kullanimi Türkçe / A-13Kimyasal Değiştirirken Arındırma İşlemi Haftalık Arındırma14 / Türkçe Islak Ovma Türkçe / A-15Islak Vakumlama 16 / Türkçe Kullanim Sonrasi Türkçe / A-17Bakim Programi Vakum Motorunun BakimiSulu Akülerİn Şarj Edİlmesİ 18 / TürkçeAKÜ SU Sevİyesİnİn Kontrol Edİlmesİ JEL Vrla Akülerİn Şarj EdİlmesİToplayicinin Bakimi Türkçe / A-19Toplayicinin Ayarlanmasi Toplayıcı Açsının Ayarlanması…Gerİ Kazanim Tanki Anahtarlarinin Bakimi 20 / TürkçeDİsk Ünİtesİ Etek Yükseklİğİnİn Ayarlanmasi Türkçe / A-21Şekil Önden Görünüm Disk Ünitesi Etek Yüksekliğinin Ayarlamak için…22 / Türkçe Model BA 755C BA 855 EDS Türkçe / A-23Model BA 755 EDS English Table of ContentsEnglish / B-3 Parts and ServiceIntroduction NameplateSymbols Know Your Machine English / B-5English Control Panel EDS English / B-7Control Panel Standard Tank Full IndicatorEnglish / B-9 When Servicing BatteriesBatteries 10 / English Installing the Brushes Disc SystemEnglish / B-11 Install the Brushes Cylindrical SystemSqueegee Installation Filling the Solution Tank12 / English Detergent EDS System Preparation and USE English / B-1314 / English WET Scrubbing English / B-15WET Vacuuming 16 / English English / B-17 Maintenance ScheduleAfter USE Servicing the Vacuum Motor18 / English Checking the Battery Water LevelCharging WET Batteries Charging GEL Vrla BatteriesEnglish / B-19 Adjusting the SqueegeeServicing the Squeegee 20 / English Servicing the Recovery Tank SwitchesEnglish / B-21 Adjusting the Disk Deck Skirt HeightFront View Front22 / English Form NO. 56041684 BA 755, BA 855 B-23 English / B-23Page Nilfisk-Advance Incorporated Pas

56315047(855 EDS), 56315043(755C), 56315042(755), 56315045(755 EDS), 56315044(855) specifications

Nilfisk-Advance America is renowned for its high-quality cleaning solutions, and among its impressive lineup, the models 56315046 (755C EDS), 56315044 (855), 56315045 (755 EDS), 56315042 (755), and 56315043 (755C) stand out for their performance and innovation. These machines are designed to meet the needs of various industrial cleaning applications, combining advanced technology with user-centric features.

The 56315046 (755C EDS) is a compact and highly efficient ride-on scrubber dryer equipped with Nilfisk's Enhanced Floor Cleaning System (EDS). This technology enables an exceptional cleaning performance by optimizing water usage and enhancing chemical application, resulting in cleaner floors with reduced detergent use. Its ergonomic design ensures operator comfort and ease of use, making it ideal for cleaning large areas in warehouses, distribution centers, and retail spaces.

The 56315044 (855) model is a robust, durable floor scrubber that is particularly suited for heavy-duty environments. It features a versatile scrub deck that can tackle different floor surfaces, ensuring thorough cleaning without damaging delicate materials. The machine’s intuitive controls allow for easy operations, even for less experienced staff, thus minimizing training time. Its high-capacity tank ensures extended run times, which boosts productivity in larger facilities.

In contrast, the 56315045 (755 EDS) offers similar EDS technology but in a more compact form factor, making it easier to navigate tighter spaces. This model achieves a powerful clean while maintaining energy efficiency, thanks to its advanced brushless motor that reduces wear and tear while extending the machine's lifecycle. The 56315042 (755) similarly provides a strong cleaning solution but focuses on simplicity and reliability, perfect for day-to-day cleaning tasks in various industrial applications.

Finally, the 56315043 (755C) combines the ergonomic benefits of a ride-on design with the robust features seen in the other models. It incorporates user-friendly controls, allowing operators to adjust settings quickly, optimizing performance based on cleaning requirements. Equipped with superior suction capabilities, it guarantees quick drying times, minimizing slip hazards in busy environments.

Each model in the Nilfisk-Advance America lineup showcases a commitment to quality, efficiency, and user comfort, making them vital assets for any facility aiming to maintain cleanliness and hygiene standards.