Harman-Kardon AVR 430 Main Remote Control Functions, Selector, Channel Direct Inputs the input

Page 11

Main Remote Control Functions

IMPORTANT NOTE: The AVR 430’s remote may be programmed to control up to seven devices, including the AVR. Before using the remote, it is important to remember to press the Input Selector button 4that corresponds to the unit you wish to operate. In addition, the AVR’s remote is shipped from the factory to operate the AVR and most Harman Kardon CD or DVD play- ers and cassette decks. The remote is also capa- ble of operating a wide variety of other products using the control codes that are part of the remote or by learning commands from other remotes. Before using the remote with other products, follow the instructions on pages 42-45 to program the proper codes for the products in your system.

It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Input Selector Button 4. The descriptions shown here primarily detail the functions of the remote when it is used to oper- ate the AVR.

0Power Off Button: Press this button to place the AVR or a selected device unit in the Standby mode. Note that when the AVR is switched off this will turn off the main room functions, but if the Multiroom system is activated, it will continue to function.

1IR Transmitter Window: Point this window towards the AVR when pressing buttons on the remote to make certain that infrared commands are properly received.

2LCD Information Display: This two-line screen displays various information depending on the commands that have been entered into the remote.

3Power On Button: Press this button to turn on the power to a device selected by pressing one of the Input Selectors 4(except Tape).

4Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the AVR

Selector

button 5again to operate the AVR’s functions with the remote.

5AVR Selector: Pressing this button will switch the remote so that it will operate the AVR’s functions. If the AVR is in the Standby mode, it will also turn the AVR on.

6AM/FM Tuner Select: Press this button to select the AVR’s tuner as the listening choice. Pressing this button when the tuner is in use will select between the AM and FM bands.

76-Channel/8 Channel Direct Input: Press this button to select the device connected to the 6-Channel Direct Inputs or the

8-Channel Direct Inputs (the input

available will depend on the selection 5.1 or 6.1/7.1 made in the surround mode setting, see page 24 for more information).

8Test Tone: Press this button to begin the sequence used to calibrate the AVR’s output lev- els. (See page 26 for more information on calibrat- ing the AVR.)

9Sleep Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the AVR will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:

 

 

90

 

80

 

 

 

70

 

 

 

60

 

50

 

 

 

min

 

min

 

 

min

 

 

min

 

 

min

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

40

 

30

 

 

20

 

 

10

 

 

OFF

 

 

 

 

 

 

 

 

 

 

min

 

min

 

 

min

 

 

min

 

 

 

 

 

 

 

 

 

 

 

 

 

Hold the button pressed for two seconds to turn off the Sleep mode setting.

Note that this button is also used to change channels on your TV, VCR and Sat receiver when the appropriate source is selected, using the device Input Selectors 4.

ASurround Mode Selector: Press this but- ton to select any of the HALL, THEATER or VMAx surround modes. Note that depending on the type of input, some modes are not always avail- able. (See page 29 for more information about surround modes.) Note that this button is also used to tune channels on your TV, VCR and Sat receiver when the appropriate source is selected using the device Input Selector 4.

BNight Mode: Press this button to activate the Night mode. This mode is available only with Dolby Digital encoded sources, and it preserves dialog (center channel) intelligibilty at low vol- ume levels (See page 26 for more information).

CChannel Select Button: This button is used to start the process of setting the AVR’s output levels with an external source. Once this button is pressed, use the ⁄/¤ buttons Eto select the channel being adjusted, then press the Set button F, followed by the ⁄/¤ buttons Eagain, to change the level setting. (See page 35 for more information.)

DDim Button: Press this button to activate the Dimmer function, which reduces the bright- ness of the front-panel display, or turns it off entirely. Press the button once to change the dis- play to reduce the brightness by 50%, and press it again within five seconds and the main display will go completely dark. Note that this setting is

temporary; regardless of any changes, the display will always return to full brightness when the AVR is turned on. The blue illumination around the Standby/On Button 1 will always remain at full brightness regardless of the setting to remind you that the AVR is still turned on. The blue accent lighting inside the volume control will also remain at full brightness when the panel is at 50%, but go out when the panel lights are fully dimmed.

ENavigation Button: This single disc-like button is used to change or scroll through items in the on-screen menus or on the front panel or to make configuration settings such as digital inputs or delay timing. When changing a setting, first press the button for the function or setting to be changed (e.g., press the Digital Select Button Gto change a digital input) and then press one of these buttons to scroll through the list of options or to increase or decrease a set- ting. The sections in this manual describing the individual features and functions contain specific information on using these buttons for each application.

FSet Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker con- figuration and channel output level adjustment.

GDigital Select: Press this button to assign

one of the digital inputs *Ó to a source. (See page 33 for more information on using digital inputs.)

HNumeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

ITuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so MANUAL appears in the Main Information Display ˜, pressing the Tuning buttons K) will move the frequency up or down in single-step increments. When the FM band is in use and AUTO appears in the Main Information Display ˜, pressing this button will change to monaural reception making even week stations audible. (See page 40 for more information.)

JDirect Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys Hto select a station (See page 40 for more information on the tuner).

MAIN REMOTE CONTROL FUNCTIONS 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents AVR 430 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesUnpacking Introduction / Safety InformationImportant Safety Information Front Panel Controls For more information Coaxial ÓDigital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet AC Power Cord Jack Connect the AC Unswitched Outlet+ and negative terminals AVR 430 when appropriate upgrades are availableLight Button Main Remote Control FunctionsChannel Direct Inputs the input Main Remote Control FunctionsSelector Main Remote Control Functions Main Remote Control Functions Multi IR input jack Zone II Remote Control FunctionsOutput jacks Installation and ConnectionsAudio Equipment Connections Video Equipment ConnectionsScart A/V Connections Important Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMultiroom IR Link System and Power ConnectionsMain Room Remote Control Extension AC Power ConnectionsSpeaker Selection Speaker PlacementInput Setup System ConfigurationUsing the On-Screen Display System SetupSet Button F Audio SetupComponent Video Inputs may be On the remote Speaker SetupTo bring up the Speaker Setup menu Figure System Configuration Surround Setup Delay Settings Adjustments for Other InputsButton on the remote Night Mode SettingsOutput Level Adjustment Using EzSetMicrophone Sensor at the top An indication that the volume control was set too lowPress the Clear Button Volume until you can hear the test noise clearlyOperation Surround Mode ChartBut no surround speakers No delay availableMix of the in-phase material of the left and right channels No surround channelsChannel/8-Channel Direct Input Basic OperationSource Selection One of the most important features Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsMP3 Audio Playback Digital Audio PlaybackDolby Digital PCM Audio PlaybackSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Audio, while the main feature is availablePuts for Tape Outputs Output Level Adjustment With Source SignalsNight Mode Tape RecordingDim Function Memory BackupSet Button Fto activate the Channel Adjust menu Figure Front-Panel-Display Fade Advanced FeaturesTurn On Volume Level Surround Amplifier Channel AssignmentInstallation Advanced Features / Multiroom OperationSemi-OSD Settings Full-OSD Time Out AdjustmentAt the Multi in line, press the ‹/› buttons Multiroom SetupMultiroom Operation RS-232 ControlBasic Tuner Operation Multiroom Operation / Tuner OperationRDS Display Options RDS TuningTuner Operation RDS OperationAppears Configuring the RemotePreprogrammed Code Entry Fappears Learning CommandsAutomatic Code Entry Changing Devices Programming the RemoteRecording a Macro Macro ProgrammingRead a Macro Punch-Through ConfigurationPower On VID 2/TV VID 3/Cable AVR Logic 7 O Erasing a MacroChannel Punch-Through Volume Punch-ThroughReturning the Volume Control Settings to Default Operation Returning the Channel Control Settings to Default Operation⁄¤ Navigation Buttons Eonce so that EzSet ConfigurationEzset Disable appears in the lower line of the LCD display Transport Punch-ThroughRenaming Individual Keys RenamingRenaming a Device ‹/› Navigation Buttons Eas requiredSee page 34 for more information Resetting the RemoteAt this point you have two options Additional Notes on Configuring and Operating the Remote Press the AVR Selector Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International
Related manuals
Manual 52 pages 53.72 Kb

AVR 430 specifications

The Harman-Kardon AVR 430 is a versatile and powerful audio-video receiver that has made a significant mark in the world of home entertainment. Designed for audiophiles and casual listeners alike, the AVR 430 combines advanced technology with user-friendly features, making it an excellent choice for anyone looking to elevate their home theater experience.

One of the standout features of the AVR 430 is its multi-channel audio processing capability. It supports Dolby Digital and DTS surround sound formats, providing immersive audio that allows users to experience movies, music, and games in a whole new way. This receiver is equipped with 5.1 channel amplification, delivering a robust output of up to 70 watts per channel, ensuring that even the most demanding audio tracks come through with clarity and impact.

In terms of connectivity, the AVR 430 offers a range of input options. It includes multiple HDMI inputs that support high-definition video and audio, making it easy to connect modern devices such as Blu-ray players, gaming consoles, and streaming devices. It also features optical, coaxial, and analog inputs, providing compatibility with a variety of audio sources. Furthermore, the inclusion of a dedicated subwoofer output allows users to enhance their system with a powerful subwoofer for deeper bass response.

The AVR 430 is designed with user convenience in mind. It features an intuitive on-screen display that simplifies setup and navigation through various input sources and audio settings. The remote control is ergonomically designed and includes dedicated buttons for quick access to frequently used functions. One noteworthy technology embedded in this receiver is the proprietary Harman Kardon Logic 7 processing, which creates a wider soundstage and more realistic surround sound from stereo sources.

Additionally, the AVR 430 is built with high-quality components that ensure durability and longevity. Its sleek and stylish design allows it to seamlessly integrate into any home entertainment environment. The receiver is also known for its ability to maintain high audio fidelity, thanks to its high-current amplifier design and advanced digital circuitry.

In summary, the Harman-Kardon AVR 430 is an outstanding audio-video receiver that caters to both audiophiles and casual users. Its combination of powerful amplification, extensive connectivity options, intuitive controls, and high-quality sound processing technologies make it a top choice for anyone looking to upgrade their home theater system. Whether enjoying a blockbuster film or listening to favorite music tracks, the AVR 430 delivers an impressive audio experience that is sure to impress.
Top Page Image Contents