Harman-Kardon AVR 430 owner manual System Configuration

Page 23

System Configuration

puts and LARGE must be selected for the front speakers (and NONE for the subwoofer, see below).

3.When you have completed your selection for the front channel, press the ¤ Button Eon the remote to move the cursor to CENTER.

4.Press the ‹/› Buttons Eon the remote to select the option that best describes your center speaker, based on the speaker definitions shown below.

When SMALL is selected, low-frequency center channel sounds will be sent to the Fronts, if they are set to LARGE and Sub is turned off (see below). When Sub is on, low frequency center channel sounds will be sent to the subwoofer only.

When LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the sub- woofer output (except when the Pro Logic II Music mode is in use).

NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a problem with your receiver.

When NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a “phantom” center channel mode. Center-channel information will be sent to the left and right front channel outputs and the center channel bass will be sent to the subwoofer output when SUB L/R+LFE is selected in the SUBWOOFER line in this menu (see below). This mode is needed if no Center speaker is used. Note that when the Logic 7 Cinema or Enhanced surround modes are selected a Center speaker must be used, the Logic 7 Music mode works well without a Center too.

5.When you have completed your selection for the center channel, press the ¤ Button Eon the remote to move the cursor to SURROUND.

6.Press the ‹/› Buttons Eon the remote to select the option that best describes the surround speakers in your system based on the speaker definitions shown on page 22.

When SMALL is selected, with all digital sur- round modes low-frequency surround channel sounds will be sent to the Fronts when Sub is turned off or to the subwoofer output when Sub is on. With any analog surround mode the rear bass feed depends on the mode selected and the setting of the Sub and front speakers.

When LARGE is selected, a full-range output will be sent to the surround channel outputs (with all analog and digital surround modes), and, except with Hall and Theater modes, NO surround channel bass will be sent to the subwoofer out- put.

When NONE is selected, surround-sound infor- mation will be split between the front left and front right outputs. For optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used.

When you are using surround back speakers with your system, press the ¤ Button Eon the remote to move the cursor to SURR BACK. This line serves two functions in that it not only configures the setting for the surround back chan- nels when they are present, it also tells the AVR’s processing system to configure the unit for either 5.1 or 6.1/7.1 operation.

Press the ‹/ › Buttons on the remote to select the option that best describes the speakers in use at the left and right back surround positions based on the definitions on this page:

When NONE is selected, the system will adjust so that only 5.1-channel surround processing/ decoding modes are available and the surround back amplifier channels will not be used. When this is the case for your system you may wish to take advantage of the availability of this amplifier channel pair for use in powering a second set of speakers that have their source selected by the AVR’s multiroom control system. See page 38 for more information.

When SMALL is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and low-frequency information below the crossover point (identical with the one for the surround speakers) will be sent to the subwoofer output when the subwoofer is set to ON, or to the Front LEFT/RIGHT when subwoofer is set to OFF.

When LARGE is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and a full-range signal will be sent to the surround back channels, with no low-frequency information sent to the subwoofer output.

7.When you have completed your selection for the surround channels, press the ¤ Button Eon the remote to move the cursor to LFE.

8.Press the ‹/› Buttons Eon the remote to select the option that best describes your system.

The choices available for the subwoofer position will depend on the settings for the other speakers, particularly the front left/right positions.

If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the “on” position.

If the front left/right speakers are set to LARGE, three options are available:

•If no subwoofer is connected to the AVR, press the ‹/› Buttons Eon the remote so that NONE appears in the on-screen menu. When this option is selected, all bass information will be routed to the front left/right “main” speak- ers.

•If a subwoofer is connected to the AVR, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR is being used with a digital source that contains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies. To select that option press the ‹/› Buttons Eon the remote so that SUB (LFE) appears in the on-screen menu.

•If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers, regardless of the type of program source or Surround mode you are listening to, press the ‹/› Buttons Eon the remote so that SUB L/R+LFE appears in the on-screen menu. When this option is selected, a full-range signal will be sent to the front left/right “main” speakers. The subwoofer will receive the front left and right bass frequen- cies under the crossover frequency selected in another setting on this menu, as described below, and also the LFE soundtrack.

9.When all initial speaker “size” settings have been made, you now have the option to take advantage of the AVR’s Quadruple Crossover system, which allows individual crossover settings to be made for each speaker grouping set to "Small". The low-fre- quency crossover point is set by the design of your speakers. It is defined as the frequency which is the lowest possible frequency the speaker is capable of reproducing. Before making any changes to the set- tings for the crossover point we suggest that you find the crossover point for the speakers in each of the four groupings, front left/right, center, surround and surround back by looking at the specifications page of the speaker’s owner’s manual, by getting that information from the manufacturer’s Web site, or by contacting your dealer or the manufacturer’s customer service department. You will need this fig- ure to accurately configure the next group of set- tings.

The factory default setting for all speaker positions is 100Hz. If that setting is acceptable for all channels, then no adjustments are needed and you may skip this section. However, should you wish to change one of the settings, please proceed by pressing the

⁄Button Eso that the cursor moves back up to the top of the list of setting options. Press the ‹/ › Buttons Eso that X-OVERis highlighted and the menu data will change to the screen shown in Figure 5.

SYSTEM CONFIGURATION 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR 430 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesUnpacking Introduction / Safety InformationImportant Safety Information Front Panel Controls For more information Coaxial ÓDigital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet AC Power Cord Jack Connect the AC Unswitched Outlet+ and negative terminals AVR 430 when appropriate upgrades are availableLight Button Main Remote Control FunctionsChannel Direct Inputs the input Main Remote Control FunctionsSelector Main Remote Control Functions Main Remote Control Functions Multi IR input jack Zone II Remote Control FunctionsOutput jacks Installation and ConnectionsAudio Equipment Connections Video Equipment ConnectionsScart A/V Connections Important Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMultiroom IR Link System and Power ConnectionsMain Room Remote Control Extension AC Power ConnectionsSpeaker Selection Speaker PlacementInput Setup System ConfigurationUsing the On-Screen Display System SetupSet Button F Audio SetupComponent Video Inputs may be On the remote Speaker SetupTo bring up the Speaker Setup menu Figure System Configuration Surround Setup Delay Settings Adjustments for Other InputsButton on the remote Night Mode SettingsOutput Level Adjustment Using EzSetMicrophone Sensor at the top An indication that the volume control was set too lowPress the Clear Button Volume until you can hear the test noise clearlyOperation Surround Mode ChartBut no surround speakers No delay availableMix of the in-phase material of the left and right channels No surround channelsChannel/8-Channel Direct Input Basic OperationSource Selection One of the most important features Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsMP3 Audio Playback Digital Audio PlaybackDolby Digital PCM Audio PlaybackSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Audio, while the main feature is availablePuts for Tape Outputs Output Level Adjustment With Source SignalsNight Mode Tape RecordingDim Function Memory BackupSet Button Fto activate the Channel Adjust menu Figure Front-Panel-Display Fade Advanced FeaturesTurn On Volume Level Surround Amplifier Channel AssignmentInstallation Advanced Features / Multiroom OperationSemi-OSD Settings Full-OSD Time Out AdjustmentAt the Multi in line, press the ‹/› buttons Multiroom SetupMultiroom Operation RS-232 ControlBasic Tuner Operation Multiroom Operation / Tuner OperationRDS Display Options RDS TuningTuner Operation RDS OperationAppears Configuring the RemotePreprogrammed Code Entry Fappears Learning CommandsAutomatic Code Entry Changing Devices Programming the RemoteRecording a Macro Macro ProgrammingRead a Macro Punch-Through ConfigurationPower On VID 2/TV VID 3/Cable AVR Logic 7 O Erasing a MacroChannel Punch-Through Volume Punch-ThroughReturning the Volume Control Settings to Default Operation Returning the Channel Control Settings to Default Operation⁄¤ Navigation Buttons Eonce so that EzSet ConfigurationEzset Disable appears in the lower line of the LCD display Transport Punch-ThroughRenaming Individual Keys RenamingRenaming a Device ‹/› Navigation Buttons Eas requiredSee page 34 for more information Resetting the RemoteAt this point you have two options Additional Notes on Configuring and Operating the Remote Press the AVR Selector Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International
Related manuals
Manual 52 pages 53.72 Kb

AVR 430 specifications

The Harman-Kardon AVR 430 is a versatile and powerful audio-video receiver that has made a significant mark in the world of home entertainment. Designed for audiophiles and casual listeners alike, the AVR 430 combines advanced technology with user-friendly features, making it an excellent choice for anyone looking to elevate their home theater experience.

One of the standout features of the AVR 430 is its multi-channel audio processing capability. It supports Dolby Digital and DTS surround sound formats, providing immersive audio that allows users to experience movies, music, and games in a whole new way. This receiver is equipped with 5.1 channel amplification, delivering a robust output of up to 70 watts per channel, ensuring that even the most demanding audio tracks come through with clarity and impact.

In terms of connectivity, the AVR 430 offers a range of input options. It includes multiple HDMI inputs that support high-definition video and audio, making it easy to connect modern devices such as Blu-ray players, gaming consoles, and streaming devices. It also features optical, coaxial, and analog inputs, providing compatibility with a variety of audio sources. Furthermore, the inclusion of a dedicated subwoofer output allows users to enhance their system with a powerful subwoofer for deeper bass response.

The AVR 430 is designed with user convenience in mind. It features an intuitive on-screen display that simplifies setup and navigation through various input sources and audio settings. The remote control is ergonomically designed and includes dedicated buttons for quick access to frequently used functions. One noteworthy technology embedded in this receiver is the proprietary Harman Kardon Logic 7 processing, which creates a wider soundstage and more realistic surround sound from stereo sources.

Additionally, the AVR 430 is built with high-quality components that ensure durability and longevity. Its sleek and stylish design allows it to seamlessly integrate into any home entertainment environment. The receiver is also known for its ability to maintain high audio fidelity, thanks to its high-current amplifier design and advanced digital circuitry.

In summary, the Harman-Kardon AVR 430 is an outstanding audio-video receiver that caters to both audiophiles and casual users. Its combination of powerful amplification, extensive connectivity options, intuitive controls, and high-quality sound processing technologies make it a top choice for anyone looking to upgrade their home theater system. Whether enjoying a blockbuster film or listening to favorite music tracks, the AVR 430 delivers an impressive audio experience that is sure to impress.
Top Page Image Contents